Trane TR200 MCB 105 User manual

Rev.2008-12-17130R0476 MI11A102 *MI11A102*
MCB 105 - Relay I/O
Option Module
Operating Instructions
December 2008
TR200
BAS-SVX29A-EN
BAS-SVX29A-EN
Trane has a policy of continous product and product data improvement and reserves the right to
change design and specifications without notice.
www.trane.com
For more information, contact your local Trane
office or e-mail us at [email protected]
Literature Order Number BAS-SVX29A-EN
Date December 2008
Supersedes

Warnings, Cautions and Notices
Note that warnings, cautions and notices appear at appropriate intervals throughout this manual. Warnings are
provide to alert installing contractors to potential hazards that could result in personal injury or death. Cautions
are designed to alert personnel to hazardous situations that could result in personal injury, while notices indicate
a situation that could result in equipment or property-damage-only accidents.
Your personal safety and the proper operation of this machine depend upon the strict observance of these
precautions.
Warnings, Cautions and Notices appear at appropriate sections throughout this literature. Read these carefully.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. It could also
be used to alert against unsafe practices.
NOTICE
Indicates a situation that could result in equipment or property-damage only accidents.
Note
Indicates something important to be noted by the reader.
✮Indicates default setting
TR200 MCB 105 Relay I/O Option Module 1

TR200 MCB 105 Relay I/O Option Module
The MCB 105 option includes 3 pieces of change over contacts and can be fitted into option slot B.
Electrical Data:
Max. terminal load (AC) 240 V AC 2A
Max. terminal load (DC) 24 V DC 1A
Min. terminal load (DC) 5 V 10 mA
Max. switching rate at rated load/min. load 6 min-1/20 sec-1
WARNING
Hazardous voltage with Dual Supply!
• The label MUST be placed on the keypad frame as shown (UL approved).
• The power to the frequency converter must be disconnected.
• The power to the livepart connections on relay terminals must be disconnected.
Failure to follwo recommendations could result in death or serious injury.
• Remove the keypad, the terminal cover and the cradle from the frequency converter.
• Fit the MCB 105 option in slot B.
• Connect the control cables and relieve the cables by the enclosed cable strips.
• Various systems must not be mixed.
• Fit the extended cradle and terminal cover.
• Replace the keypad.
• Connect power to the frequency converter.
• Select the relay functions in par. 5-40 [6-8], par. 5-41 [6-8] and par. 5-42 [6-8].
Array [6] is relay 7, array [7] is relay 8 and array [8] is relay 9.
TR200 MCB 105 Relay I/O Option Module
2TR200 MCB 105 Relay I/O Option Module

Illustration 1. 1: Correct relay wiring
NOTICE
Do not combine liveparts and PELV systems.
Illustration 1. 2: Correct wire inserting.
TR200 MCB 105 Relay I/O Option Module
TR200 MCB 105 Relay I/O Option Module 3

Rev.2008-12-17130R0476 MI11A102 *MI11A102*
MCB 105 - Relay I/O
Option Module
Operating Instructions
December 2008
TR200
BAS-SVX29A-EN
BAS-SVX29A-EN
Trane has a policy of continous product and product data improvement and reserves the right to
change design and specifications without notice.
www.trane.com
For more information, contact your local Trane
office or e-mail us at [email protected]
Literature Order Number BAS-SVX29A-EN
Date December 2008
Supersedes