Transition Networks SISTG1040-242-LRT User manual

TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page1of31
SISTG1040-242-LRT and -282-LRT
Industrial Unmanaged GbE Switches
   
SISTG1040‐242‐LRT  SISTG1040‐282‐LRT
InstallGuide
33735Rev.B

TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page2of31
Trademarks
Alltrademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.
Copyright Notice/Restrictions
Copyright©2018TransitionNetworks.Allrightsreserved.Nopartofthisworkmaybereproducedorusedin
anyformorbyanymeans(graphic,electronicormechanical)withoutwrittenpermissionfromTransition
Networks.PrintedintheU.S.A.
SISTG1040‐242‐LRTand‐282‐LRTIndustrialUnmanagedGbESwitchesInstallGuide33735Rev.B

Contact Information
TransitionNetworks
10900RedCircleDrive
Minnetonka,MN55343USA
tel:+1.952.941.7600|tollfree:1.800.526.9267|fax:952.941.2322
[email protected]|[email protected]|[email protected]
Revision History
Rev.DateDescription
A3/9/18InitialreleaseatCodeversion1.0.
B7/3/18AddClassI,Division2information.

TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page3of31
CautionsandWarnings
Definitions
Cautionsindicatethatthereisthepossibilityofpoorequipmentperformanceorpotentialdamagetothe
equipment.Warningsindicatethatthereisthepossibilityofinjurytoperson.
CautionsandWarningsappearhereandmayappearthroughoutthismanualwhereappropriate.Failuretoread
andunderstandtheinformationidentifiedbythissymbolcouldresultinpoorequipmentperformance,damage
totheequipment,orinjurytopersons.
Cautions
Whileinstallingorservicingthepowermodule,wearagroundingdeviceandobserveallelectrostatic
dischargeprecautions.Failuretoobservethiscautioncouldresultindamageto,orfailureofthepower
module.
Warnings

Warning:Donotconnectthepowermoduletoanexternalpowersourcebeforeinstallingitintothechassis.
Failuretoobservethiswarningcouldresultinanelectricalshock,evendeath.
WARNING:Equipmentgroundingisvitaltoensuresafeoperation.Theinstallermustensurethatthepower
moduleisproperlygroundedduringandafterinstallation.Failuretoobservethiswarningcouldresultinan
electricshock,evendeath.
WARNING:Areadilyaccessible,suitableNationalElectricalCode(NEC)orlocalelectricalcodeapproved
disconnectdeviceandbranch‐circuitprotectormustbepartofthebuilding'sinstalledwiringtoaccommodate
permanentlyconnectedequipment.Failuretoobservethiswarningcouldresultinanelectricshock,evendeath.
WARNING:TurnanyexternalpowersourceOFFandensurethatthepowermoduleisdisconnectedfromthe
externalpowersourcebeforeperforminganymaintenance.Failuretoobservethiswarningcouldresultinan
electricalshock,evendeath.
WARNING:EnsurethatthedisconnectdevicefortheexternalpowersourceisOPEN(turnedOFF)before
disconnectingorconnectingthepowerleadstothepowermodule.Failuretoobservethiswarningcouldresult
inanelectricshock,evendeath.
SeeElectricalSafetyWarningsonpage27forElectricalSafetyWarningstranslatedintomultiplelanguages.

TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page4of31
Contents
1.Introduction.....................................................................................................................................6
Models.......................................................................................................................................................6
Features.....................................................................................................................................................6
Specifications.............................................................................................................................................7
PortConfiguration.................................................................................................................................7
HardwarePerformance.........................................................................................................................7
EnvironmentalRange............................................................................................................................7
Dimensions,Weights,Mounting...........................................................................................................7
VoltageandFrequency..........................................................................................................................7
CertificationsandCompliance...............................................................................................................8
Applications...............................................................................................................................................9
AboutThisManual....................................................................................................................................
9
RelatedManuals........................................................................................................................................9
2.SwitchOverview............................................................................................................................10
PackageContents....................................................................................................................................10
Unpacking................................................................................................................................................10
FrontPanels.............................................................................................................................................11
BackPanelandBottomPanel..................................................................................................................12
RESETButton...........................................................................................................................................12
LEDDescriptions......................................................................................................................................13
PowerLEDs..........................................................................................................................................13
SystemLED..........................................................................................................................................13
3.Installation.....................................................................................................................................15
MountingtheSwitchonaDINRail..........................................................................................................15
MountingtheSwitchonWall(Optional).................................................................................................16
GroundingScrew.....................................................................................................................................17
InstallingSFPModules.............................................................................................................................18
ConnectingtoNetwork/Devices............................................................................................................18
ConnectingtheTerminalBlock................................................................................................................18

TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page5of31
PowerSupplyFeaturesandSpecifications..............................................................................................19
25135IndustrialPowerSupplyOptionalAccessory.......................................................................19
25130IndustrialPowerSupplyOptionalAccessory.......................................................................19
ConnectingtoDCPower..........................................................................................................................19
PowerConnectionProcedure.............................................................................................................20
4.Troubleshooting.............................................................................................................................21
BasicTroubleshooting.............................................................................................................................21
LEDTroubleshooting...............................................................................................................................21
DeviceLabelandPackagingLabel...........................................................................................................22
RecordDeviceandSystemInformation..................................................................................................23
5.RegulatoryandSafetyInformation.................................................................................................24
ComplianceandSafetyStatements.........................................................................................................24
DeclarationofConformity.......................................................................................................................24
CertificateofCompliance........................................................................................................................25
UserInformation.....................................................................................................................................26
CautionsandWarnings............................................................................................................................27
ElectricalSafetyWarnings.......................................................................................................................28
6.Service,Warranty&TechSupport..................................................................................................29
Warranty..................................................................................................................................................29
ContactUs...............................................................................................................................................30



TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page6of31
1.Introduction
TheTransitionNetworksSISTG1040‐2x2‐LRTindustrialunmanagedGbEswitchesareaplug‐and‐playEthernet
switchesofferinganeasywaytomakethetransitiontoGigabitEthernetandincreasethespeedofyournetwork
connections.Theenergyefficient,builttolast,andrigorouslytestedswitchesprovidethereliabilitybusinesses
need,andtheyaresuitableforindustrialEthernetapplications.TheSISTG1040‐2x2‐LRTseriesincludestwo
models,theSISTG1040‐242‐LRTandtheSISTG1040‐282‐LRT.
Models
Thismanualdocumentsthemodelsbelow.Modelsdiffermainlyinportcount,anddifferencesarenoted
whereapplicablethroughoutthismanual.
ModelDescription
SISTG1040‐242‐LRT
UnmanagedfullGigabitEthernethardenedswitchwith(4)10/100/1000Base‐Tportsand
two100/1000dualspeedSFPslots.Hasredundantinputpowerconnectionsforsafe,
reliableoperationintemperaturesof‐40°C‐+75°C.IncludesDINRailKit.
SISTG1040‐282‐LRTUnmanagedfullGigabitEthernethardenedswitchwith(8)10/100/1000Base‐Tportsand
two100/1000dualspeedSFPslots.IncludesDINRailKit.
Options(soldseparately)
25135OptionalIndustrialPowerSupplyOptionalAccessory(soldseparately).
Input:85‐264VDC,120‐370VDC.Output:24VDC,10Watts,‐20°Cto+70°C.
25130OptionalIndustrialPowerSupplyOptionalAccessory(soldseparately).
Input:88‐264VDC,120‐370VDC.Output:48VDC,39.8Watts,‐20°Cto+70°C.
WMBH‐01OptionalWallMountablebrackets.
SFPModulesSeeTransitionNetworksSFPwebpagefordetails.
Features
SlimtypeindustrialEthernetswitch
IEEE802.3azEnergyEfficientEthernetstandardforgreenEthernetapplications.Theswitchdesignhelps
savepowerandreduceTCOinagreenEthernetnetworkenvironment.
Layer2wire‐speedswitchingengine
Ruggedizedmetalclosure
Fan‐lessdesign

TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page7of31
Specifications
Port Configuration
ModelTotalPortsRJ45
(10M/100M/1G)SFP(100M/1G)Console
SISTG1040‐242‐LRT642‐‐
SISTG1040‐282‐LRT1082‐‐
Hardware Performance
ModelForwarding
Capacity(Mpps)
Switching
Capacity(Gbps)
MacTable
(K)
JumboFrames
(Bytes)
SISTG1040‐242‐LRT8.9281249K
SISTG1040‐282‐LRT14.882049K
Environmental Range
OperatingTemperatureStorageTemperatureOperating
HumidityAltitude
FahrenheitCentigradeFahrenheitCentigrade5%to95%
non‐condensing
FeetMeters
‐40to167 ‐40to75 ‐40to185 ‐40to85<10000<3000
Dimensions, Weights, Mounting
Model
Dimensions(WxHxD)Weight
MountingType
MillimetersInchesKilogramsPounds
SISTG1040‐242‐LRT44x135x1301.7x5.3x5.10.360.79DINrail,Wall
SISTG1040‐282‐LRT44x135x1301.7x5.3x5.10.860.39DINrail,Wall
Voltage and Frequency
PrimaryPowerSupply‐DCInputVoltage
DCNominal12/24/48VDCdualinputs
DCOperatingRange9.6to57VDC
DCPower
Consumption
SISTG1040‐242‐LRT:4.4Wattsmax.
SISTG1040‐282‐LRT:5.8Wattsmax.


TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page8of31
Certifications and Compliance
RegulatoryCompliance
EMS
IEC61000‐4‐2ed1.2:2001:ESDTestlevel3:8kVcontact,15kVair
EN61000‐4‐4EFT–DC:2KV(upto4KV)
EN61000‐4‐4EFT–SignalPorts:1KV(upto2KV)
EN61000‐4‐3RadiatedImmunity–Enclosure:10V/m(upto6GHz)
EMI
FCCpart15approvalClassA;CEmarking
CISPR22/EN55022ClassAandCISPR24/EN55024ClassA;VCCIJapan
EN61000‐3‐2Ed.3.0AmendmentA11998AmendmentA21998ClassA
IEC61000‐3‐3Ed2:2008ElectromagneticCompatibility–Limitationofvoltage
fluctuationandflickerinlowvoltagesupplysystemsforequipmentratedupto16A
ClassC"
SafetyCE
StandardsIEEE802.3;IEEE802.3u;IEEE802.3z;IEEE802.3ae;IEEE802.3x;IEEE802.1p;IEEE
802.3az
ProtocolsCSMA/CD
ComplianceULClass1/Div2;EMI:CE,FCCPart15
CompliantEN50121‐4,EN50155,NEMATS‐2,IEC61850‐3,IEEE1613
MTBF
ModelMTBFEnvironment
SISTP1040‐242‐LRT
1,188,425Hrs.GB,GC‐GroundBenign,Controlled.Temp:25.00deg.C.
211,393Hrs.GB,GC‐GroundBenign,Controlled.Temp:75.00deg.C.
SISTP1040‐282‐LRT
1,043,630Hrs.GB,GC‐GroundBenign,Controlled.Temp:25.00deg.C.
184,723Hrs.GB,GC‐GroundBenign,Controlled.Temp:75.00deg.C.

TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page9of31
Applications
ThisSISTG1040‐2x2‐LRTunmanagedfullGigabitEthernethardenedswitchescanbeusedattheedgeofa
hardenednetworktoprovideGigabitEthernetconnectionsinhazardouslocations.Thefiberuplinkportscan
alsobeusedinadaisychainformaximumnetworkreliability.Redundantinputpowerconnectionsensuresafe
reliableoperationattemperaturesof‐40°Cto+75°C.TransitionNetworks’hardenedswitchesarecertifiedto
operatereliablyinharshenvironmentssuchasthosefoundonfactoryfloors,outdoorenclosuresorother
hazardousenvironments.
AboutThisManual
ThismanualdescribeshowtoinstallandtroubleshoottheSISTG1040‐2x2‐LRTswitch,includinghowto:
Installtheswitch.
ChecktheswitchstatusLEDbehavior.
Resettheswitchorrestoretheswitchtofactorydefaults.
Troubleshootswitchinstallation.
RelatedManuals
AprintedQuickStartGuideisshippedwitheachswitch.
ForTransitionNetworksDrivers,Firmware,etc.gototheProductSupportwebpage(logonrequired).
ForManuals,ApplicationNotes,Brochures,DataSheets,Specifications,etc.gototheSupportLibrary(nologon
required).
NotethatthismanualprovideslinkstothirdpartywebsitesforwhichTransitionNetworksisnotresponsible.


TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page10of31
2.SwitchOverview
PackageContents
Verifythatyouhavereceivedtheitemsbelow.Contactyoursalesrepresentativeifanyitemismissing.
Pleasesavethepackagingforpossiblefutureuse.
TheSwitch
TerminalBlock
QuickStartGuide
Mountingkit
IndustrialPowerSupply(OptionalAccessory‐soldseparately)
 

Unpacking
Unpackandverifythecontentsintheirinstalllocation,andcontinuewithoneofthemountingprocedures
(Desktop,DINRail,orWallmounting)inchapter3.

TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page11of31
FrontPanels

SISTG1040‐242‐LRTFrontPanel

SISTG1040‐282‐LRTFrontPanel

TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page12of31
BackPanelandBottomPanel
  
BackPanelBottomPanel

RESETButton
PresstheRESETbuttontoreboottheswitch.ThefrontpanelLEDsflashandtheswitchisreset.




TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page13of31
LEDDescriptions
ThefrontpanelLEDsletyoucheckandmonitorswitchstatus.ThethreetypesoffrontpanelLEDsare:
PowerLEDs(P1,P2)indicateiftheswitchispoweredupcorrectly.
SystemLEDindicatesifthesystemisready.
PortStatusLEDsindicatesthecurrentstatusofeachport.ChecktheseLEDstounderstandtheportstatus.
ThefollowingtablesdescribetheLEDindicatorfunctions.
Power LEDs
LEDColorStateDescription
P1
Power1
Green
OnTheswitchispoweredONcorrectly.
OffTheswitchisnotreceivingpowerfromthefirstpowersource.
P2
Power2
Green
OnTheswitchispoweredoncorrectly.
OffTheswitchisnotreceivingpowerfromthesecondpowersource.

System LED
LEDColorStateDescription
SYS
System
Green
OnTheswitchisready.
OffTheswitchisnotready.


TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page14of31
Port Status LEDs
ThetablebelowdescribesportstatusLEDbehaviors.
LEDColorStateDescription
RJ45Ports
(LeftSide)
GreenOn
Theportisenabledandhasestablishedalinktoaconnecteddevice,
andtheconnectionspeedis1000Mbps.
GreenBlinking
Theportistransmitting/receivingpackets,andtheconnectionspeed
is1000Mbps.
AmberOn
Theportisenabledandhasestablishedalinktoconnecteddevice,
andtheconnectionspeedis10/100Mbps.
AmberBlinking
Theportistransmitting/receivingpackets,andtheconnectionspeed
is10/100Mbps.
‐‐ Off
Theporthasnoactivenetworkcableconnected,orithasnot
establishedalinktoaconnecteddevice.
SFPPorts
GreenOn
Theportisenabledandhasestablishedalinktoaconnecteddevice,
andtheconnectionspeedis1000Mbps.
GreenBlinking
Theportistransmitting/receivingpackets,andtheconnectionspeed
is1000Mbps.
AmberOn
Theportisenabledandhasestablishedalinktoaconnecteddevice,
andtheconnectionspeedis100Mbps.
AmberBlinking
Theportistransmitting/receivingpackets,andtheconnectionspeed
is100Mbps.
‐‐ Off
Theporthasnoactivenetworkcableconnected,orithasnot
establishedalinktoconnecteddevice.
10/100/1000RJ‐45PortLEDs 100/1000SFPPortLEDs

TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page15of31
3.Installation
MountingtheSwitchonaDINRail
1.AttachtheDINRailmountingkittorearpanelofthechassis.Insertscrewsandtightenwithascrewdriverto
securethekit.

2.InserttheupperlipoftheDINrailintotheDIN‐railmountingkit.PresstheswitchtowardstheDINrailuntilit
snapsintoplace.
 
3.MakesurethattheswitchisattachedsecurelytoDINRail.


TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page16of31
MountingtheSwitchonWall(Optional)
UsetheOptionalWallMountablebrackets(WMBH‐01option).
1.Attachthewallmountingplatestorearpanelofthechassis.Insertscrewsandtightenthenwithascrewdriver
tosecuretheplates.


2.Installuser‐suppliedscrewsontheappropriatelocationonthewall.
3.Makesurethattheswitchisattachedsecurelytothewall.

TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page17of31
GroundingScrew
Thefrontpanelgroundingscrew( )isusedforgrounding.Groundingandwire
routinghelplimittheeffectsofnoiseduetoelectromagneticinterference(EMI).
Runthegroundconnectionfromthegroundscrewstothegroundingsurfaceprior
toconnectingdevices.





TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page18of31
InstallingSFPModules
Theswitchprovidestwo100M/1GSFPs.Youcaninstallorremoveamini‐GBICSFPmodulefromaSFPport
withouthavingtopowerofftheswitch.TransitionNetworksoffersafulllineofsmallformfactorpluggable(SFP)
transceivers.SeeourSFPwebpagefordetails.RefertothespecificSFPmanualforcautionsandwarnings.
Note:TheSFPportsshoulduseULListedOptionalTransceiverproduct,Rated3.3Vdc,LaserClass1.
1. InsertthemoduleintotheSFPport(cage).
2. WiththeSFPmodulealignedcorrectly,slidethemoduleintotheSFPslotuntilyouhearaclick.
3. Pressfirmlytoensurethatthemoduleseatsintotheconnector.

4. Insertthefibercableintothetransceiver.
ConnectingtoNetwork/Devices
Theswitchesprovideeightorfour10M/100M/1GRJ45ports.UseCat5eorbetterunshieldedtwistedpair(UTP)
cableterminatedwithanRJ‐45connector.
Usefourtwisted‐pair,Category5eorabovecablingforRJ‐45portconnection.Thecablebetweentheswitch
andthelinkpartner(switch,hub,PC,etc.)mustbelessthan100meters(328ft.)long.
AFibersegmentusingsingle‐modeconnectortypemustuse9/125μmsingle‐modefibercable.
AFibersegmentusingmulti‐modeconnectortypemustuse50or62.5/125μmmulti‐modefibercable.
ConnectingtheTerminalBlock
TheswitchshipswithakeyedTerminalblock(Euroblock).UnpacktheTerminalblock
andinsertitintothereceptacle.Itiskeyedsoitcanonlybeinsertedcorrectly.Youcan
useasmallflat‐bladescrewdrivertoremoveaninsertedTerminalblock.

TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page19of31
PowerSupplyFeaturesandSpecifications
TwoIndustrialPowerSupplyoptionsareavailable(soldseparately).
25135 Industrial Power Supply Optional Accessory
Input:85‐264VDC,120‐370VDC.Output:24VDC,10Watts,‐20°Cto+70°C.
SeetheTransitionNetworkswebpageformoreinformation.
25130 Industrial Power Supply Optional Accessory
Input:88‐264VDC,120‐370VDC.Output:48VDC,39.8Watts,‐20°Cto+70°C.
SeetheTransitionNetworkswebpageformoreinformation.
ConnectingtoDCPower
TheSISTG1040‐2x2‐LRTshipswithnoPowerCord.TheSISTG1040‐2x2‐LRTcanbeorderedwithoptional
accessories(soldseparately)includingIndustrialPowerSupplyPN25130or25135.
Thissectionisforreferenceonlyassiterequirementscanvarygreatly.Forexample,theswitchcanbepowered
fromaDINrailoritcanbepoweredwithaPDU(PowerDistributionUnit).TypicallyaPDUwoulddeliver48volts,
butaPDUcanprovidehighervoltageswherethe25130or25135wouldneedtobeused.SeethePDUmanual
forPDUinstallationandoperation.
Caution:BesurethepowercordisdisconnectedfromACpowerbefore
connectingthepowercordtotheSISTG1040‐2x2‐LRTswitch.
UsetheprocedurebelowtoconnectPowerSupplyDCtotheSwitchandconnect
ACtothewalloutlet.

TransitionNetworks SISTG1040‐2x2‐LRTInstallGuide
33735Rev.Bhttps://www.transition.com Page20of31
Power ConnectionProcedure
Caution:BeforeapplyingpowerfromanACoutlet,insertterminalconnectorsintotheSISTG1040‐2x2‐LRT
switchandverifyallconnections.Plugginginpowerconnectionafterenergizingpowersupply(s)maydamage
theswitch.
1. Payingcloseattentiontothepolaritymarkings,connectthewiresbetweenthe+P1and–P1terminalson
theswitchterminalblockandthe+Vand‐Vterminalsonthepowersupply.Optionally,connectthewires
betweenthe+P2and–P2terminalsontheswitchterminalblockandthe+Vand‐Vterminalsonthepower
supplyifredundantpoweristobeused.
2. UseasmallPhillipsscrewdrivertotightenthewire‐clampscrews.

PowerSupplyDCtoSwitchandACtoWallOutlet
3. Connectthethreewires(e.g.,green,black,white)ofthepowercordtothepowersupplyGround(),N,
andLclampconnectionsrespectively.UseasmallPhillipsscrewdrivertotightenthewire‐clampscrews.
4. ConnecttheplugendofthepowercordintoaliveACoutlet.
5. VerifythatthePowerSupplyfrontpanelDCOKLEDislit.