Transition Networks SM12DP2XA User manual

TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 1of 254
SM12DP2XA
Managed Gigabit Ethernet Fiber Switch
(12) 100/1000Base-X SFP Slots + (2) 1G/10G SFP+ slots + (2)
10/100/1000Base-T



CLIReference
33753Rev.A

TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 2of 254
Trademarks
Alltrademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.
Copyright Notice/Restrictions
Copyright©2018TransitionNetworks.Allrightsreserved.Nopartofthisworkmaybereproducedorused
inanyformorbyanymeans(graphic,electronicormechanical)withoutwrittenpermissionfromTransition
Networks.PrintedintheU.S.A.
SM12DP2XAManagedGigabitEthernetFiberSwitchCLIReference33753Rev.A
Contact Information
TransitionNetworks
10900RedCircleDrive
Minnetonka,MN55343USA
tel:+1.952.941.7600|tollfree:1.800.526.9267|fax:952.941.2322
[email protected]|[email protected]|[email protected]
Revision History
RevDateDescription
A6/20/18InitialreleaseatFWv7.10.14232018‐05‐16.



TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 3of 254
Contents
1‐Introduction..................................................................................................................................................5
1‐1KeyFeatures............................................................................................................................................5
1‐2RelatedManuals......................................................................................................................................5
1‐3ForMoreInformation.............................................................................................................................6
1–4CLIManagement.....................................................................................................................................6
1‐5Login........................................................................................................................................................6
1‐6CLICommandModes..............................................................................................................................7
1‐7GlobalCLICommands..............................................................................................................................8
2–ClearCommands........................................................................................................................................12
3–ConfigureCommands................................................................................................................................24
3‐1access‐list...............................................................................................................................................95
3‐2no.........................................................................................................................................................103
3‐3qos.......................................................................................................................................................131
3‐4snmp‐server.........................................................................................................................................138
3‐5spanning‐tree......................................................................................................................................146
4‐CopyCommands.......................................................................................................................................151
5–PlatformDebugCommands....................................................................................................................152
6–DeleteCommands...................................................................................................................................153
7‐DIRCommands.........................................................................................................................................154
8‐DisableCommands...................................................................................................................................155
9‐DoCommands..........................................................................................................................................156
10‐Dot1XCommands...................................................................................................................................157
11‐EnableCommands..................................................................................................................................158
12‐FirmwareCommands.............................................................................................................................159
13‐NoCommands........................................................................................................................................160
14‐PingCommands......................................................................................................................................161
15‐ReloadCommands..................................................................................................................................163
16‐SendCommands.....................................................................................................................................164
17‐ShowCommands....................................................................................................................................165
18‐TerminalCommands..............................................................................................................................222
19‐IPCommands..........................................................................................................................................224
20‐CLICommandReference........................................................................................................................225
20‐1PrivilegeLevels..................................................................................................................................225
22‐Troubleshooting,Warranty,SupportandCompliance..........................................................................249

TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 4of 254
22‐1RecordingDeviceandSystemInformation.......................................................................................250
22‐2LimitedLifetimeWarranty................................................................................................................251
22‐3ContactUs.........................................................................................................................................251
AppendixA‐DHCPPerPort..........................................................................................................................252
ConfigureDHCPPerPortviatheCLI.........................................................................................................252


TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 5of 254
1‐Introduction
TheSM12DP2XAManagedGigabitEthernetFiberSwitchisanext‐generationFiberSwitchofferingfullsuite
ofL2featuresandadditional10GbEuplinkconnections.AdvancedL3featuressuchasStaticRoutedeliver
bettercostperformanceandlowertotalcostofownershipinenterprisenetworksorbackboneviafibberor
copperconnections.
TheSM12DP2XAprovides12GbESFPports,2RJ45ports,210GbESFP+portsandRJ45Consoleportwith
built‐inACandDCdualpowersupply.TheSM12DP2XAprovidesfrontpanelaccesstoallpower,dataand
managementportsinacompactformfactorfordesktop,wall‐mount,orrack‐mountinstallations.
1‐1KeyFeatures
IPv6Management
SupportJumboFrameupto9Kbytes
Authentication–RADIUS,TACACS+
IEEE802.1X:RADIUSauthentication,authorizationandaccounting,MD5hash,guestVLAN,
single/multiplehostmodeandsingle/multiplesessions
DHCPRelay,DHCPOption82,DHCPSnooping,DHCPServer,DHCPPerPort
L2/L3/L4ACLssupportMAC,VLANIDorIP,protocol,port,DSCP/IPprecedence/TCP.UDP,EtherType,
ICMP,TCPflag
LLDP(LinkLayerDiscoveryProtocol)
IPSourceGuard,PortSecurity
PortMirroring
FirmwareUpdatethroughTFTP/HTTPandconsole
Syslog
1RUhigh,compactformfactor
Extendedoperatingtemperature:‐20°Cto+60°C
1‐2RelatedManuals
SM12DP2XAQuickStartGuide,33750
SM12DP2XAInstallGuide,33751
SM12DP2XAWebUserGuide,33752
SM12DP2XACLIReference,33753(thismanual)

TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 6of 254
1‐3ForMoreInformation
AprintedQuickStartGuideisshippedwitheachunit.
ForTransitionNetworksDrivers,Firmware,etc.gototheProductSupportwebpage(logonrequired).
ForTransitionNetworksManuals,Brochures,DataSheets,etc.gototheSupportLibrary(nologon
required).ForSFPmanualsseeTransitionNetworksSFPwebpage.
Note:Informationinthisdocumentissubjecttochangewithoutnotice.Notethatthismanualprovides
linkstothirdpartywebsitesforwhichTransitionNetworksisnotresponsible.
1–4CLIManagement
Abriefdescriptionofthenetworkconnectionisprovidedbelow.
TheRJ‐45cableisusedforconnectingaterminalorterminalemulatortotheSwitch’sRJ‐45porttoaccess
thecommandlineinterface.AttachtheRJ‐45serialportontheswitch’sfrontpanelwhichusedtoconnect
totheswitchforconsoleconfiguration.AttachtheotherendoftheDB‐9cabletoanASCIIterminal
emulatororPCCom‐1,2port(e.g.,aPCrunningMicrosoftWindowsHyperTerminalutility).
Atthe“ComPortProperties”Menu,configuretheparametersBaudrate=115200,Stopbits=1,Databits=8,
Parity=N,Flowcontrol=none.
1‐5Login
Thecommand‐lineinterface(CLI)isatext‐basedinterface.UsercanaccesstheCLIthrougheitheradirect
serialconnectiontothedeviceoraTelnetsession.Thedefaultuserandpasswordtologinintothe
ManagedSwitchareUsername:adminandPassword:admin.
Afteryouloginsuccessfully,thepromptwillbeshownas“<sys_name>#“.Thismeansyoucanperformas
anadministratorandhavetheprivilegeforsettingtheManagedSwitch.Ifnotloggedinasthe
administrator,thepromptwillbeshownas“<sys_name>>”,whichmeansyoucanperformasaguestand
areonlyallowedforsettingthesystemundertheadministrator.EachCLIcommandhasaspecificprivilege
level.
loginas:admin
[email protected].77'spassword:
SM12DP2XA#
Whenapartialcommandlistdisplays,thelastlinedisplaystheseoptionsforcontinuing:
‐‐more‐‐,nextpage:Space,continue:g,quit:^C

TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 7of 254
1‐6CLICommandModes
TheCLIisdividedintoseveralmodes.Ifauserhasenoughprivilegetorunaparticularcommand,youcan
runthecommandifinthecorrectmode.Toseethecommandsofamode,enteraquestionmark(?)after
thesystemprompt,thenallcommandswillbelistedinthescreen.Thecommandmodesarelistedbelow:

ModePromptCommandFunctioninThisMode
Exec<sys_name>#Displaycurrentconfiguration,
diagnostics,maintenance.
Config<sys_name>(config)#Configurefeaturesotherthanthose
below.
Config‐if<sys_name>(config‐interface)#Configureports.
Config‐if‐vlan<sys_name>(config‐if‐vlan)#ConfigurestaticVLAN.
Config‐line<sys_name>(config‐line)#Lineconfiguration.
Config‐impc‐profile<sys_name>(config‐impc‐profile)#ConfigureIPMCProfile.
Config‐snmp‐host<sys_name>(config‐snmp‐host)#ConfigureSNMPServerHost.
Config‐stp‐aggr<sys_name>(config‐stp‐aggr)#ConfigureSTPAggregation.
Config‐dhcp‐pool<sys_name>(config‐dhcp‐pool)#DHCPPoolConfiguration.
Config‐rfc2544‐profile<sys_name>(config‐rfc2544‐profile)#RFC2544ProfileConfiguration.

Eachcommandresidesinacorrespondingmodeandcanrunonlyinthatmode.Ifyouwanttoruna
particularcommand,youmustchangetotheappropriatemode.Thecommandmodesareorganizedasa
tree,startinginExecmode.Thefollowingtableexplainshowtochangefromonemodetoanother.

Exec ‐‐ ‐‐
ConfigConfigureterminalexit
config‐interfaceInterface<port‐type><port‐type‐list>exit
config‐vlanInterfacevlan<vlan_list>exit





TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 8of 254
1‐7GlobalCLICommands
Execmodecommandsarelistedwiththe?(questionmark)commandasshownbelow.
SM12DP2XA#?
CableDiagCableDiagnostickeyword
clearResetfunctions
configureEnterconfigurationmode
copyCopyfromsourcetodestination
deleteDeleteonefileinflash:filesystem
dirDirectoryofallfilesinflash:filesystem
disableTurnoffprivilegedcommands
doTorunexeccommandsinconfigmode
dot1xIEEEStandardforport‐basedNetworkAccessControl
enableTurnonprivilegedcommands
exitExitfromEXECmode
firmwareFirmwareupgrade/swap
helpDescriptionoftheinteractivehelpsystem
ipIPv4commands
ipv6IPv6configurationcommands
logoutExitfromEXECmode
moreDisplayfile
noNegateacommandorsetitsdefaults
pingSendICMPechomessages
platformPlatformconfiguration
reloadReloadsystem.
sendSendamessagetootherttylines
showShowrunningsysteminformation
terminalSetterminallineparameters
traceroutetracerouteprogram
SM12DP2XA#



TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 9of 254
CableDiag
Cable Diagnostic keyword. This command runs the built-in Cable Diagnostics. It takes about 5-15 seconds. When
completed, the cable diagnostics results display in the cable status table. Note that Cable Diagnostics is only accurate for
cables of length 7 -140 meters. The 10 and 100 Mbps ports will be linked down while running Cable Diagnostics.
Running Cable Diagnostics on a 10 or 100 Mbps management port will cause the switch to stop responding until the
diagnostics complete.
Syntax: CableDiag interface GigabitEthernet <port_type_id>
Parameters:
interface Interface keyword
GigabitEthernet 1 Gigabit Ethernet Port
<port_type_id> Port ID in 1/13-14
<cr>
Example:
SM12DP2XA#CableDiag?
interfaceInterfacekeyword
SM12DP2XA#CableDiaginterface?
GigabitEthernet1GigabitEthernetPort
SM12DP2XA#CableDiaginterfaceGigabitEthernet?
<port_type_id>PortIDin1/13‐14
SM12DP2XA#CableDiaginterfaceGigabitEthernet1/13?
<cr>
SM12DP2XA#CableDiaginterfaceGigabitEthernet1/13
StartingCableDiagnostic‐Pleasewait
InterfaceLinkStatusTestResultLength
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐
GigabitEthernet1/13LinkDownAbnormal3(m)
SM12DP2XA#


TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 10 of 254
Exit
Exit from Config mode back to Exec mode.
Syntax: exit
Parameters: None.
Example:
SM12DP2XA#configureterminal
SM12DP2XA(config)#exit
SM12DP2XA#
Help
Description of the interactive help system.
Syntax: help
Parameters: None.
Example:
SM12DP2XA#help
Helpmayberequestedatanypointinacommandbyentering
aquestionmark'?'.Ifnothingmatches,thehelplistwill
beemptyandyoumustbackupuntilenteringa'?'showsthe
availableoptions.
Twostylesofhelpareprovided:
1.Fullhelpisavailablewhenyouarereadytoentera
commandargument(e.g.'show?')anddescribeseachpossible
argument.
2.Partialhelpisprovidedwhenanabbreviatedargumentisentered
andyouwanttoknowwhatargumentsmatchtheinput
(e.g.'showpr?'.)

SM12DP2XA#
logout
Exit from EXEC mode and close the session. You must log back in again.
Syntax: logout
Parameters: none
Example:
SM12DP2XA#logout

TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 11 of 254
end
Go back to EXEC mode.
Syntax: end
Example:
SM12DP2XA(config)#end
SM12DP2XA#

SM12DP2XA(config)#vlan10
SM12DP2XA(config‐vlan)#?
doTorunexeccommandsinconfigmode
endGobacktoEXECmode
exitExitfromcurrentmode
helpDescriptionoftheinteractivehelpsystem
nameASCIInameoftheVLAN
no
SM12DP2XA(config‐vlan)#exit
SM12DP2XA(config)#interface?
*AllswitchesorAllports
GigabitEthernet1GigabitEthernetPort
10GigabitEthernet10GigabitEthernetPort
vlanVLANinterfaceconfigurations
SM12DP2XA(config)#interfacevlan?
<vlan_list>ListofVLANinterfacenumbers,1~4095
SM12DP2XA(config)#interfacevlan100?
<cr>
SM12DP2XA(config)#interfacevlan100
SM12DP2XA(config‐if‐vlan)#end
SM12DP2XA#

TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 12 of 254
2–ClearCommands
Table : CLEAR Commands
access Accessmanagement
access‐listAccesslist
dot1x IEEEStandardforport‐basedNetworkAccessControl
ip InterfaceInternetProtocolconfigcommands
ipv6 IPv6configurationcommands
lacp ClearLACPstatistics
lldp ClearsLLDPstatistics.
logging Systemloggingmessage
mac MACAddressTable
mvr MulticastVLANRegistrationconfiguration
port‐securityEnable/disableportsecurityglobally.
sflow Statisticsflow.
spanning‐treeSTPBridge
statisticsClearstatisticsforoneormoregiveninterfaces
access
Access management.
Syntax: clear access management statistics
Parameters: management Access management configuration.
statistics Statistics data.
Example:
SM12DP2XA#clearaccessmanagementstatistics
SM12DP2XA#showaccessmanagementstatistics

AccessManagementStatistics:
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐
HTTPReceive:0Allow:0Discard:0
HTTPSReceive:0Allow:0Discard:0
SNMPReceive:0Allow:0Discard:0
TELNETReceive:0Allow:0Discard:0
SSHReceive:0Allow:0Discard:0
SM12DP2XA#



TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 13 of 254
access-list
Access list.
Syntax: Clear access-list ace statistics
Parameters:
ace Access list entry
statistics Traffic statistics
Example:
SM12DP2XA#clearaccess‐list?
aceAccesslistentry
SM12DP2XA#clearaccess‐listacestatistics?
<cr>
SM12DP2XA#clearaccess‐listacestatistics
SM12DP2XA#showaccess‐listacestatistics

Switchaccess‐listacenumber:0
SM12DP2XA#

dot1x
IEEE Standard for port-based Network Access Control.
Syntax
Clear dot1x statistics
Clear dot1x statistics interface GigabitEthernet < PORT_TYPE_LIST>
Parameters
statistics Clears the statistics counters
interface Interface
GigabitEthernet 1 Gigabit Ethernet Port
10GigabitEthernet 10 Gigabit Ethernet Port
PORT_TYPE_LIST Port list in 1/1-14 for Gigabit Ethernet, Port list in 1/1-2 for 10Gigabit Ethernet
EXAMPLE
SM12DP2XA#cleardot1xstatisticsinterface?
*AllswitchesorAllports
GigabitEthernet1GigabitEthernetPort
10GigabitEthernet10GigabitEthernetPort
SM12DP2XA#cleardot1xstatistics
SM12DP2XA#SM12DP2XA#

TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 14 of 254
ip
Interface Internet Protocol config commands
Syntax
clear ip arp
clear ip dhcp detailed statistics { server | client | snooping | relay | helper | all } [ interface ( <port_type>
[ <in_port_list> ] ) ]
clear ip dhcp relay statistics
clear ip dhcp server binding <ip>
clear ip dhcp server binding { automatic | manual | expired }
clear ip dhcp server statistics
clear ip dhcp snooping statistics [ interface ( <port_type> [ <in_port_list> ] ) ]
clear ip igmp snooping [ vlan <v_vlan_list> ] statistics
clear ip statistics [ system ] [ interface vlan <v_vlan_list> ] [ icmp ] [ icmp-msg <type> ]
Parameters
arp Clear ARP cache
dhcp Dynamic Host Configuration Protocol
igmp Internet Group Management Protocol
statistics Traffic statistics
relay DHCP relay agent configuration
snooping DHCP snooping
interface Select an interface to configure
GigabitEthernet 1 Gigabit Ethernet Port
10GigabitEthernet 10 Gigabit Ethernet Port
vlan IPv4 traffic interface
<vlan_list> VLAN identifier(s): VID
EXAMPLE
SM12DP2XA#clearip?
arpClearARPcache
dhcpDynamicHostConfigurationProtocol
igmpInternetGroupManagementProtocol
statisticsTrafficstatistics
SM12DP2XA#cleariparp?
<cr>
SM12DP2XA#cleariparp
SM12DP2XA#clearipdhcp?

TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 15 of 254
detailedDetailedstatistics
relayDHCPrelayagentconfiguration
serverMiscellaneousDHCPserverinformation
snoopingDHCPsnooping
SM12DP2XA#clearipigmp?
snoopingSnoopingIGMP
SM12DP2XA#clearipigmpsnooping?
statisticsRunningIGMPsnoopingcounters
vlanSearchbyVLAN
SM12DP2XA#clearipstatistics?
icmpIPv4ICMPtraffic
icmp‐msgIPv4ICMPtrafficfordesignatedmessagetype
interfaceSelectaninterfacetoconfigure
systemIPv4systemtraffic
<cr>
SM12DP2XA#clearipstatistics
SM12DP2XA#


TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 16 of 254
ipv6
IPv6 configuration commands.
Syntax
clear ipv6 mld snooping [ vlan <v_vlan_list> ] statistics
clear ipv6 neighbors
clear ipv6 statistics [ system ] [ interface vlan <v_vlan_list> ] [ icmp ] [ icmp-msg <type> ]
Parameters
mld Multicasat Listener Discovery
neighbor Ipv6 neighbors
statistics Traffic statistics
snooping Snooping MLD
statistics Running MLD snooping counters
vlan Ipv6 interface traffic
<vlan_list> VLAN identifier(s): VID
icmp IPv6ICMPtraffic
icmp-msg IPv6 ICMP traffic for designated message type
interface Select an interface to configure
system IPv6 system traffic
< 0~255> ICMP message type ranges from 0 to 255
EXAMPLE
SM12DP2XA#clearipv6?
mldMulticasatListenerDiscovery
neighborsIPv6neighbors
statisticsTrafficstatistics
SM12DP2XA#clearipv6mld?
snooping
SM12DP2XA#clearipv6mldsnoopingvlan3statistics
SM12DP2XA#clearipv6neighbors
SM12DP2XA#clearipv6statisticssystemicmpicmp‐msg2
SM12DP2XA#

TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 17 of 254
lacp
Clear LACP statistics
Syntax Clearlacp statistics
Parameters
statistics Clear all LACP statistics
EXAMPLE
SM12DP2XA#clearlacpstatistics
SM12DP2XA#
lldp
Clears LLDP statistics.
Syntax
Clear lldp statistics
Clear lldp statistics| begin | exclude | include >< LINE >
Parameters
statistics Clears LLDP statistics.
EXAMPLE
SM12DP2XA#clearlldpstatistics?
|Outputmodifiers
globalClearglobalcounters
interfaceInterfacekeyword.
<cr>
SM12DP2XA#clearlldpstatistics<tab>
globalinterface|<cr>
SM12DP2XA#clearlldpstatistics
SM12DP2XA#


TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 18 of 254
logging
Clear Syslog.
Syntax
clear logging [ info ] [ warning ] [ error ] [ switch <switch_list> ]
Parameters
alert crit debug emerg error info notice warning
EXAMPLE
SM12DP2XA#clearlogging?
alertSeverity1:Actionmustbetakenimmediately
critSeverity2:Criticalconditions
debugSeverity7:Debug‐levelmessages
emergSeverity0:Systemisunusable
errorSeverity3:Errorconditions
infoSeverity6:Informationalmessages
noticeSeverity5:Normalbutsignificantcondition
warningSeverity4:Warningconditions
<cr>
SM12DP2XA#clearlogging<tab>
alertcritdebugemergerrorinfonoticewarning
<cr>
SM12DP2XA#clearlogginginfoerrorwarning
SM12DP2XA#


TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 19 of 254
mac
Clear MAC Address Table.
Syntax
Clear mac address-table
Parameters
address-table Flush MAC Address table.
EXAMPLE
SM12DP2XA#clearmacaddress‐table
SM12DP2XA#
mvr
Clear Multicast VLAN Registration configuration.
Syntax
clear mvr [ vlan <v_vlan_list> | name <mvr_name> ] statistics
Parameters
name MVR multicast name
statistics Running MVR protocol counters
vlan MVR multicast vlan
< word16> MVR multicast VLAN name
<vlan_list> MVR multicast VLAN list
EXAMPLE
SM12DP2XA#clearmvr?
nameMVRmulticastname
statisticsRunningMVRprotocolcounters
vlanMVRmulticastvlan
SM12DP2XA#clearmvrname?
<word16>MVRmulticastVLANname
SM12DP2XA#clearmvrstatistics?
<cr>
SM12DP2XA#clearmvrvlan?
<vlan_list>MVRmulticastVLANlist
SM12DP2XA#clearmvrvlan25statistics
SM12DP2XA#

TransitionNetworksSM12DP2XACLIReference
33753 Rev. A https://www.transition.com Page 20 of 254
port-security
Clearportsecurity.
Syntax
clearport‐securitysticky{All|interface(<port_type>[<plist>])}
Parameters
sticky  portsecuritystickyfunctionperinterface
All  clearallstickymacatallports
interface Chooseport
*  AllswitchesorAllports
GigabitEthernet   1GigabitEthernetPort
10GigabitEthernet 10GigabitEthernetPort
<port_type_list> Portlistin1/1‐2
<cr>
EXAMPLE
SM12DP2XA#clearport‐security?
port‐securityEnable/disableportsecurityglobally.
SM12DP2XA#clearport‐security?
stickyportsecuritystickyfunctionperinterface.
SM12DP2XA#clearport‐securitysticky?
Allclearallstickymacatallports
interfaceChooseport
SM12DP2XA#clearport‐securitystickyinterface?
*AllswitchesorAllports
GigabitEthernet1GigabitEthernetPort
10GigabitEthernet10GigabitEthernetPort
SM12DP2XA#clearport‐securitystickyinterface10GigabitEthernet?
<port_type_list>Portlistin1/1‐2
SM12DP2XA#clearport‐securitystickyinterface10GigabitEthernet1/10?
%Nosuchinterface:10GigabitEthernet1/10

SM12DP2XA#clearport‐securitystickyinterface10GigabitEthernet1/1
SM12DP2XA#clearport‐securitystickyall?
Allclearallstickymacatallports
<cr>
SM12DP2XA#clearport‐securitystickyall?
<cr>