Travis industries 864 trv gsr2 User manual





864 TRV GSR2

(AU) Fireplace

Listed by

AS 4553-2008

GMK10026

IAPMO-R&T OCEANA

•

Built-In Direct Vent Fireplace

•

Natural Gas or Propane

•

Residential or Mobile Home

WARNING: If the information in these instructions is not followed exactly, a fire or

explosion may result causing property damage, personal injury or loss of

life.

•

DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.

•

DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.

•

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN

OPERATION.

•

DO NOT MODIFY THIS APPLIANCE.

•

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the

gas supplier.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA

only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type(s) of gas indicated on the rating plate. A conversion

kit is supplied with the appliance.

Installation Manual

Installer: After installation give this manual to the home-

owner and explain operation of this heater.

Dragon Wholesaling Pty. Ltd.

Unit 4, 16 Lexington Drive

Bella Vista NSW

Australia 2153

2 Introduction

Overview

This manual details the

installation requirements for

the 864 TRV GSR2 fireplace.

For operating and

maintenance instructions,

refer to the 864 TRV GSR2

Owner's Manual (part # 100-

01320).

IAPMO-R&T

OCEANA

Gas Mark

TM

GMK10026

864 TRV GSR2 (Au)

Vented Gas Fireplace Heater

Tested to the combustion performance and construction requirements of AS 4553-2008 Gas Space Heating

Appliances. This appliance must be installed in accordance with all local codes.

This 864 TRV GSR2 appliance is equipped from the factory only for use with Natural Gas and is only for

use with the type of gas indicated on the rating plate. For conversion to LP (Propane) use a certified kit

supplied by the manufacturer. See owner’s manual for information on making these changes.

This appliance may be installed in an aftermarket, permanently located, manufactured (mobile) home where

not prohibited by local codes.

This vented gas fireplace heater is not for use with air filters. This appliance must be properly connected to

a venting system in accordance with the manufacturer’s installation instructions. Use only approved

coaxial direct vent systems to vent this appliance to the exterior. See owner’s manual for approved brands

of venting.

WARNING:

Improper installation, adjustment, alteration, service or maintenance can cause injury or

property damage. Refer to the owner’s information manual provided with this appliance. For assistance or

additional information consult a qualified installer, service agency or the gas supplier.

This appliance is a Vented Gas Fireplace Heater. Not for use with Solid Fuel.

Young children should be carefully supervised at all times when they are in the same room

as the appliance.

Fireplace to adjacent wall

Back to enclosure

Header (from stand-offs)

25 mm

13 mm

0 mm

Sides to enclosure

Combustible floor under fireplace

Base of fireplace to a mantel

13 mm

0 mm

See Owner’s Manual

Minimum Clearances to Combustibles

FAN TYPE VENTED CIRCULATOR

Blower Electrical Rating: 240V., 1.5 Amps, 50 Hz, 150 Watts

Minimum Inlet Pressure (kPa)

Maximum Inlet Pressure (kPa)

Manifold Pressure on “HI” (kPa)

L.P.

2.74

3.24

2.74

N.G.

1.37

1.74

.87

Input Rate on “HI” (MJ/h)

Input Rate on “LO” (MJ/h)

Orifice Size - Front (DMS)

Orifice Size - Rear (DMS)

L.P.

32.7

8.4

#56

#57

N.G.

32.7

10.5

#49

This appliance is equipped for installation 0-610 m. For altitudes above 600m, the vent configuration, orifice, or

combination of both may need to be changed. See owner’s manual for information on making these changes.

2014

2015

2013

Feb.

Mar.

Jan.

May

Jun.

Apr.

Aug.

Sep.

Jul.

Nov.

Dec.

Oct.

MANUFACTURE DATE:

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

Manufactured by: Certificate Holder:

www.lopi.com.au

Dragon Wholesaling Pty. Ltd.

Unit 4, 16 Lexington Drive

Bella Vista NSW 2153

Australia

0842

Table of Contents 3

Introduction

Overview.............................................................................2

Safety Precautions

Safety Precautions..............................................................4

Features and Specifications

Features..............................................................................6

Installation Options..............................................................6

Heating Specifications.........................................................6

Dimensions .........................................................................6

Installation

Packing List.........................................................................7

Additional Items Required...................................................7

Installation Overview...........................................................7

Recommended Installation Procedure ................................7

Converting the Fireplace to Top Vent Configuration ...........8

Fireplace Placement Requirements....................................10

Clearances......................................................................10

Raised Fireplaces............................................................10

Min. Framing Dims. - Rear Vent Configuration...........................11

Min. Framing Dims. - Top Vent Configuration .................12

Nailing Brackets ..............................................................13

Corner Installations - Rear Vent Configuration................14

Corner Installations - Top Vent Configuration..................15

Gas Line Requirements ......................................................16

Fuel .................................................................................16

Gas Line Connection.......................................................16

Gas Inlet Pressure...........................................................16

Gas Line Location............................................................16

Electrical Connection (required)..........................................18

Vent Requirements .............................................................19

Vent Clearances..............................................................19

Altitude Considerations....................................................19

Approved Vent.................................................................20

Vent Installation...............................................................20

Approved Vent Configurations ............................................21

Restrictor Position ...........................................................21

Exhaust Restrictor Adjustment ........................................21

Intake Restrictor Adjustment ...........................................22

Diffuser Plate Adjustment................................................23

Rear Vent Config. W Horizontal Term. (no vertical rise) .....24

Rear Vent Config. W Horizontal Term. (w vertical rise).......25

Rear Vent Configuration with Vertical Termination..............26

Top Vent Configuration with Horizontal Termination...........27

Top Vent Configuration with Vertical Termination...............28

Termination Requirements..................................................29

Installation (continued)

Hearth Requirements.......................................................... 30

Facing Requirements.......................................................... 31

Drywall Installation ..........................................................31

Facing Overview .............................................................32

Optional Faceplates – Sizing Chart.................................32

Thin Facing Installation ...................................................33

Thick Facing Installation..................................................35

Thick Facing Installation with FPX Arched Faces............36

Mantel Requirements.......................................................... 38

Install Example - Build-Out (Dog-House) w Hor. Term. ......38

Install Example - Build-In w Hor. Term................................ 40

Finalizing the Installation

Steps for Finalizing the Installation ..................................... 41

Air Shutter Adjustment ....................................................42

Glass Frame Removal and Installation............................... 43

Log Set Installation ............................................................. 45

LP Conversion Instructions................................................. 52

Optional Equipment

Fireback Installation............................................................ 55

Grill Installation................................................................... 56

Index

Index................................................................................... 58

4 Safety Precautions

Safety Warnings:

•Failure to follow all of the requirements may result in property damage, bodily injury, or even death.

•This unit must be installed by a qualified installer to prevent the possibility of an explosion.

•This appliance must be installed in accordance with all local codes, if any; if not, in U.S.A. follow

ANSI Z223.1 and NFPA 54(88).

•A manufactured home (USA only) or mobile home OEM installation must conform with the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a

standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS

A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4. This

appliance may be installed in Manufactured Housing only after the home is site located.

•All exhaust gases must be vented outside the structure of the living-area. Combustion air is drawn

from outside the living-area structure. The venting must not be connected to a chimney flue serving a

separate solid-fuel burning appliance.

•Notify your insurance company before hooking up this fireplace.

•The room heater should be inspected before use and at least annually by a qualified service person.

More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.

•The instructions in this manual must be strictly adhered to. Do not use makeshift methods or

compromise in the installation. Improper installation will void the warranty and safety listing.

•This heater is approved for use with natural gas (NG) or propane (LP). Burning the incorrect fuel will

void the warranty and safety listing and may cause an extreme safety hazard. Direct questions about

the type of fuel used to your dealer. Check the label and flame adjust knob on the gas control valve.

•Contact your local building officials to obtain a permit and information on any installation restrictions

or inspection requirements in your area.

•If the flame becomes sooty, dark orange in color, or extremely tall, do not operate the heater. Call

your dealer and arrange for proper servicing.

•It is imperative that control compartments, screens, or circulating air passageways of the heater be

kept clean and free of obstructions. These areas provide the air necessary for safe operation.

•Do not operate the heater if it is not operating properly in any fashion or if you are uncertain. Call

your dealer for a full explanation of your heater and what to expect.

•Do not store or use gasoline or other flammable liquids in the vicinity of this heater.

•Do not operate if any portion of the heater was submerged in water or if any corrosion occurs.

•Do not place clothing or other flammable items on or near the heater. Because this heater can be

controlled by a thermostat there is a possibility of the heater turning on and igniting any items placed

on or near it.

•Light the heater using the built-in piezo igniter. Do not use matches or any other external device to

light your heater.

•Never remove, replace, modify or substitute any part of the heater unless instructions are given in this

manual. All other work must be done by a trained technician. Don't modify or replace orifices.

•The viewing glass should be opened only for conducting service.

•Any safety screen or guard removed for servicing must be replaced prior to operating the heater.

Safety Precautions 5

Safety Warnings (continued):

•Allow the heater to cool before carrying out any maintenance or cleaning.

•Operate the heater according to the instructions included in this manual.

•If the main burners do not start correctly turn the gas off and call your dealer for service.

•This unit is not for use with solid fuel.

•Do not place anything inside the firebox (except the included fiber logs).

•If the fiber logs become damaged, replace with Travis Industries log set.

•Do not throw this manual away. This manual has important operating and maintenance instructions

that you will need at a later time. Always follow the instructions in this manual.

•Do not touch the hot surfaces of the heater. Educate all children of the danger of a high-temperature

heater. Young children should be supervised when they are in the same room as the heater.

•Due to the high temperature, the heater should be located out of traffic and away from furniture and

draperies.

•Instruct everyone in the house how to shut gas off to the appliance and at the gas main shutoff valve.

The gas main shutoff valve is usually next to the gas meter or propane tank and requires a wrench to

shut off.

•Travis Industries, Inc. grants no warranty, implied or stated, for the installation or

maintenance of your heater, and assumes no responsibility of any consequential damage(s).

SAFETY WARNINGS:

•DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.

•DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.

•DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS

IN OPERATION.

•DO NOT MODIFY THIS APPLIANCE.

•THIS INSTALLATION MUST CONFORM WITH THE FOLLOWING:

−Manufacturer’s Installation instructions

−Local Gas Fitting Regulations

−Municipal Building Codes,

−Refer to AS/NZS 5601.1 for Gas Installations.

−S.A.A. Wiring Code

−Local Electrical Regulations

−Any other statutory regulations

•NOT SUITABLE FOR MARINE USE.

•NOT INTENDED FOR FIREPLACE INSERT.

APPLIANCES INCORPORATING A LIVE FUEL EFFECT, AND DESIGNED TO

OPERATE

6 Features and Specifications

Installation Options

•Residential or Mobile Home

•Straight or Corner Placement

•Flush or Recessed Face

•Raised or Floor Placement

•Internal or External Chase

•Horizontal or Vertical Vent

•Bedroom Approved

Heating Specifications

Natural Gas Propane

Approximate Heating Capacity (in square feet)* 1,400 1,400

Approximate Heating Capacity (in square meters)* 129 129

Maximum BTU Input Per Hour 31,000 31,000

Maximum Megajoules (MJ) Input Per Hour 32.7 32.7

* Heating capacity will vary with floor plan, insulation, and outside temperature.

Dimensions

* Includes the required

1/2" (13mm) clearance.





30-3/4"

781mm

Back of Fireplace

38-1/4"

972mm

36-3/4"

933mm

41"

1041mm

19-3/4"*

502mm*

38-3/8"

975mm

29-1/4"*

743mm*

Weight: 205 Lbs. (93 Kg)

37"

940mm

35-1/4"

895mm

7-1/4"

184mm

1"

25mm

Top Vent Configuration

8" (203mm) Ø Vent

Rear Vent Configuration

8" (203mm) Ø Vent

Installation (for qualified installers only) 7

Packing List

•Propane Conversion Kit

•Log Set

•Firestop (sku 93006094)

•Remote

Additional Items Required

•Direct Vent

•Gas Line Equipment (shutoff valve, pipe, etc.)

•Electrical Equipment (min. 14 gauge, grounded line)

Installation Overview

•All requirements below must be met.





See the section

"Approved Vent

Configurations"

See the section

"Electrical Connection"

See the section

"Mantel Requirements"

Insulation must not fill

the 1/2" (13mm)

clearance around the

back and sides of the

fireplace.

See the section

"Vent Requirements"

See the section "Minimum

Framing Dimensions"

Drywall

Top Vent

Configuration Rear Vent

Configuration

See the section

"Gas Line Installation"

1" Min.

25mm

Side

Wall









See "Optional Non-

Combustible Facing"

Drywall

See "Optional Non-

Combustible Hearth"

Nailing Brackets

Required  Travis

Firestop (sku

93006094)

Recommended Installation Procedure

•Frame the opening for the fireplace. Make sure to allow for vent installation.

•This fireplace is designed to accommodate 1/2" (13mm) or 5/8" (16mm) drywall (see "Nailing

Brackets" on page 13 for details). Secure the fireplace to the framing.

•Install the vent, gas line and electrical hook-up.

•Install the drywall.

•Install the hearth (if applicable).

•Install the facing (if applicable).

•Install the mantel (if applicable).

•Finalize the installation (see page 41) and install the grill or face.

8 Installation (for qualified installers only)

Top Vent or Rear Vent Configuration

This appliance is shipped in the rear vent configuration. To change to the top vent configuration, follow

the directions below.

NOTE: the vent configuration affects several aspects of installation (framing, maximum vent rise,

maximum vent run). Make sure the vent configuration is correct prior to installation. You may wish to

configure the diffuser when changing the vent configuration.

Converting the

Fireplace to Top

Vent

Configuration

Remove and discard all of

the insulation found near

the flue assembly (make

sure to remove every

piece).



Remove the 4 screws

securing the intake cover

plate. Remove it and place it

aside.



Remove the 4 screws

securing the cover plate.

Remove it and place it

aside.



Remove the 4 screws

securing the cover plate (with

hole).

This part may be discarded.

Top of Fireplace

Back of Fireplace



Installation (for qualified installers only) 9

Converting the

Fireplace to Top

Vent (continued)

Remove the 12 screws

securing the flue assembly.

Attach the intake cover

plate with the screws

removed earlier.

Attach the cover plate with

the screws removed earlier.

NOTE: flatten the four legs

before insaling the cover

plate.

Rotate the flue

assembly so the

flue points

upwards. Secure

using the twelve

screws removed

earlier.

NOTE: Use a magnetic-

tipped nutdriver on these

screws - take care to prevent

the screws from falling into

the fireplace.

DO NOT OVER-

TIGHTEN THE

SCREWS.

10 Installation (for qualified installers only)

Fireplace Placement Requirements

•The fireplace requires a 1/2" (13mm) clearance from the angled sides and back of the fireplace to the

framing members. No material (insulation, framing, etc.) may be placed into this area.

•Fireplace must be installed on a level surface capable of supporting the fireplace and vent

•Fireplace must be placed directly on wood or non-combustible surface (not on linoleum or carpet)

•This heater may be placed in a bedroom. Please be aware of the large amount of heat this appliance

produces when determining a location.

Clearances

•When installed, walls in front of the fireplace must be a minimum 1" (25mm) to the side of the

fireplace.

•Due to the high temperature, the heater should be located out of traffic and away from furniture and

draperies.

•Fireplace must be placed so the vents below and above the glass do not become blocked.

Raised Fireplaces

•The fireplace (and hearth, if desired) may be placed on a platform designed to support the fireplace

(205 Lbs. 93 Kg) and vent.

Installation (for qualified installers only) 11

Minimum Framing Dimensions - Rear Vent Configuration











Route the

electrical line to

a position to the

left rear of the

fireplace.

Vent Clearances 8" (203mm) dia. Vent:

1" (25mm) to the sides, 1" (25mm)

below, and 3" (76mm) above the vent to

combustibles.

Included Firestop (required)

Part # 93006094

Center of Rear Vent











30-3/4"

781mm

38"

965mm

41-1/4"

1048mm

38-1/2"

978mm

20"

508mm

HINT: place the fireplace so the center

line is at least 5" (127mm) from both

vertical framing members at the rear (this

allows the vent to pass through the

framing without modfications)

25-3/4"

654mm

The on/off switch/thermostat wire (if

used) should be routed to a location

near the right front of the fireplace.

Minimum enclosure height = 38-1/2" (978mm)

12 Installation (for qualified installers only)

Minimum Framing Dimensions - Top Vent Configuration

Route the electrical line to

a position to the left rear

of the fireplace.

41-1/4"

1048mm

38-1/2"

978mm

20" (508mm)

The on/off switch/thermostat wire (if

used) should be routed to a location

near the right front of the fireplace.

Minimum enclosure height = 38-1/2" (978mm)

Installation (for qualified installers only) 13

Nailing Brackets

The fireplace has nailing brackets on both sides. Secure the fireplace to the framing.

NOTE: Make sure the fireplace is square and plumb when placed in the framing. Measured corner-

to-corner the fireplace should be square (approx. 54-7/8” – 1394mm). See the illustration below.

Use shims to insure the fireplace is square.



1/2''(13mm)

5/8''(16mm)



5/8" (16mm)

Additional nailing brackets

are provided along the base

of the fireplace. Use these

brackets if not using the front

brackets.

54-7/8''

(1394mm)

1/2" (13mm)

14 Installation (for qualified installers only)

Corner Installations - Rear Vent Configuration

A typical 45° installation uses the framing dimensions shown in the illustration below (NOTE: all

clearances still apply).



7-1/2" (91mm)

Approximate

(varies due to vent

installation)









48" Min.

1219mm

Minimum 1/2" (13mm) Clearance

NOTE:

Most installations use:

6" (152mm) Section for

2 X 6 Walls (51mm X 152mm)

4" (102mm) Section for

2x4 Walls (21mm X 102mm)

(Travis # 98900166)



Minimum 1" (25mm) Clearance



Travis Firestop

(sku 93006094)

Installation (for qualified installers only) 15

Corner Installations - Top Vent Configuration

A typical 45° installation uses the framing dimensions shown in the illustration below (NOTE: all

clearances still apply).



15-1/2"

394mm







48" Min.

1219mm

Minimum 1/2" (13mm) Clearance



16 Installation (for qualified installers only)

Gas Line Requirements

MASSACHUSETTS INSTALLATIONS - WARNING:

THIS PRODUCT MUST BE INSTALLED BY A LICENSED PLUMBER OR GAS FITTER WHEN INSTALLED WITHIN THE

COMMONWEALTH OF MASSACHUSETTS.

OTHER MASSACHUSETTS CODE REQUIREMENTS:

•Flexible connector must not be longer than 36 inches.

•Shutoff valve must be a “T” handle gas cock.

•Only direct vent sealed combustion products are approved for bedrooms or bathrooms.

•Fireplace dampers must be removed or welded in the open position prior to the installation of a fireplace insert or gas log.

•A carbon monoxide (CO) detector is required in the same room as the appliance.

•The gas line must be installed in accordance with all local codes, if any; if not, follow ANSI 223.1 and

the requirements listed below.

•The fireplace and gas control valve must be disconnected from the gas supply piping during any

pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPA). For pressures

under 1/2 psig (3.5 kPA), isolate the gas supply piping by closing the manual shutoff valve.

•Leak test all gas line joints and the gas control valve prior to and after starting the fireplace.

Fuel

•This fireplace is designed either for natural gas or for propane (but not for both). Check the sticker on the top of

the gas control valve to make sure the correct fuel is used.

Gas Line Connection

•Installation must be performed by a qualified installer, service agency or the gas supplier (In Massachusetts a

licensed plumber/gasfitter).

Gas Inlet Pressure Standard Input Pressure

Natural Gas 7" W.C. (1.74 kPA)

Propane 13" W.C. (2.73 kPA)

•If the pressure is not sufficient, make sure the piping used is large enough, the supply regulator is adequately

adjusted, and the total gas load for the residence does not exceed the amount supplied.

•The supply regulator (the regulator that attaches directly to the residence inlet or to the propane tank) should

supply gas at the suggested input pressure listed above. Contact the local gas supplier if the regulator is at an

improper pressure.

Installation (for qualified installers only) 17

Gas Line Location

NOTE: The shutoff valve is attached to the side of the fireplace. If using rigid pipe, the shutoff valve may

be removed from the cover plate and attached to the shutoff valve inside the fireplace.

10"

254mm

15 degrees

3" (77mm) Above Base

5.75"

147mm

15 degrees

3" (77mm) Above Base

Right Side Gas Line (Stock)

Left Side Gas Line

Converting Gas Line to the Left Side

1. Disconnect the gas line from the shutoff valve (3/4” wrench). Gas line is located inside the fireplace

on the right side.

2. Remove the screw that holds the shutoff valve plate in place (1/4” nutdriver). Remove the shutoff

valve plate.

3. Remove the cover plate from the left side of the fireplace (it is held in place in the same fashion as

the shutoff valve plate). Attach it to the right side of the fireplace.

4. Attach the shutoff valve plate to the left side of the fireplace. Route the gas line to the left side and

re-attach the gas line to the shutoff valve. Make sure to leak test the entire gas line.

18 Installation (for qualified installers only)

Electrical Connection (required)

•The electrical line to the grounded receptacle inside the fireplace must be installed by a qualified

installer and must meet all local codes.

•Make sure the household breaker is shut off prior to working on any electrical lines.

•The appliance, when installed, must be electrically grounded in accordance with local codes or, in the

absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical

Code, CSA C22.1.

•The electrical line must be a min. 14 gauge, and supply 240 Volts at 50 Hz (2 Amps)

Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause

improper and dangerous operation.

abcd

Installation (for qualified installers only) 19

Vent Requirements

•The gas appliance and vent system must be vented directly to the outside of the building, and never

be attached to a chimney serving a separate solid fuel or gas-burning appliance. Each direct vent

gas appliance must use it's own separate vent system.

•In addition to the requirements listed here, follow the requirements provided with the vent.

•A firestop is required whenever the vent penetrates a wall, floor, or ceiling (passes through framing

members). Horizontal vent less than 48" (1219mm) above the fireplace must use the Travis Firestop

(sku 93006094 - it incorporates a 3" (76mm) clearance above, 1" (25mm) clearance below and to the

sides of the vent). Other penetrations only require a 1" (25mm) clearance and may use a standard

firestop (make sure the required 1" (25mm) clearance is met).

Vent Clearances

•The vent must maintain the required clearance to combustible materials to prevent a fire. Do not fill

air spaces with insulation.

Before 48" (1219mm) Rise After 48" (1219mm) Rise

Sides 1" (25mm) 1" (25mm)

Above 3" (76mm) 1" (25mm)

Below Horizontal or 45° Section 1" (25mm) 1" (25mm)

Horizontal

Termination

Required Firestop

Min. 3" (76mm)

(1" or 25mm if a

minimum 48"or

1219mm above the

fireplace)

Min. 1" (25mm)

Use a firestop whenever

passing through a ceiling

Vertical Termination

Use a roof flashing and storm collar

whenever passing through the roof

Min. 1"(25mm)

Use a support box

on exposed vent

Altitude Considerations

•This heater has been tested at altitudes ranging from sea level to 6,000 feet (1800 M). In this testing we have

found that the heater, with its standard orifice, burns correctly with just an air shutter adjustment.

•Failure to adjust the air shutter properly may lead to improper combustion which can create a safety hazard.

Consult your dealer or installer if you suspect an improperly adjusted air shutter.

20 Installation (for qualified installers only)

Approved Vent

•Rear vent configurations use 8" (203mm) diameter Simpson Dura-Vent Model Direct-Vent Pro (or

GS)*.

•Top vent configurations use 8" (203mm) or 6-5/8" (168mm) diameter Simpson Dura-Vent Direct-Vent

Pro (or GS)*. If using 6-5/8" (168mm) diameter vent, attach the 8" (203mm) to 6-5/8" (168mm)

reducer (Travis part # 98900165) to the fireplace.

NOTE: When using 6-5/8” (168mm) diameter vent, make sure to accommodate the 3” (76mm)

clearance above the vent for the first 48” (1219mm) of rise (see vent clearances on page 19).

Standard firestops do not include this clearance.

* Other vent may be approved with this fireplace. Check with the vent manufacturer for details.

•Always use the high-wind cap (or high-wind sconce cap, part # 58DVA-HSCH or 46DVA-HSCH).

•Installation instructions for Simpson Dura-Vent may be found at www.duravent.com

6-5/8" (168mm) Diameter Vent

Reducer - # 98900165

Vent Installation

•Slide the vent sections together and turn 1/4 turn until the sections lock in

place.

•Screws are not required to secure the vent. However, three screws may be

used to secure vent sections together if desired.

•High temperature sealant is recommended at the appliance starter section

connection (use high-temperature silicone or Mill-Pac®).

•If disassembly is required, at time of re-assembly check to see if the vent

creates a tight fit. If it does not, apply high temperature sealant to the joints

of the affected sections.

•Horizontal sections require a 1/4" (6mm) rise every 12" (305mm) of travel

•Horizontal sections require non-combustible support every three feet (e.g.: plumbing tape)

Travis Industries 864 TRV GSR2 User manual

Popular Indoor Fireplace manuals by other brands