TRENDnet N300 TEW-739APBO User manual

ŸN300 Outdoor PoE Access Point
TEW-739APBO
TEW-739APBO (V1) /06.19.2014
ŸQuick Installation Guide (1)

ŸTEW-739APBO
ŸCD-ROM (User's Guide)
ŸMulti-Language Quick Installation Guide
ŸProprietary PoE injector
ŸPower adapter (48 V DC, 0.5 A)
ŸMounting hardware
ŸWaterproof RJ-45 plug (network cable is not included)
ŸGrounding wire
Package Contents
1. Before You Start
1
Installation Requirements
ŸRequires antennas: TEW-AO46S or TEW-AO57
ŸComputer with a network port and web browser
ŸA network switch or router with an available network LAN port
ŸRJ-45 network cables (sold separately)
ŸPhillips screwdriver
Note:
ŸThe TEW-739APBO does not support IEEE 802.3at/af. You must use the proprietary Power
over Ethernet injector that is supplied with the TEW-739APBO.

2
2. Hardware Configuration
Note: The default IP address of the TEW-739APBO is 192.168.10.100. To configure the
TEW-739APBO, your network adapter must have an IP address within the 192.168.10.x subnet
(e.g. 192.168.10.50). Please refer to the Appendix in the User's Guide for more information.
Phase 1: Access Point Setup
Note:
ŸThe initial configuration should be completed in a testing environment. Configure the device
before mounting.
Included PoE injector

3
5. Connect the other end of a network cable to your computer's Ethernet port.
6. Connect the power adapter into the Power over Ethernet Injector. Then connect the power
adapter into a power outlet. (For EU version, toggle the power switch to the “On” position).
7. Assign a static IP address to your computer's network adapter in the subnet of 192.168.10.x
(e.g. 192.168.10.25) and a subnet mask of 255.255.255.0.
1. Connect the TEW-AO46S or the TEW-AO57 antennas to the TEW-739APBO.
2. Connect one end of a network cable into the TEW-739APBO.
3. Connect the other end of the network cable to the P+DATA OUT port on the Power over
Ethernet Injector.
4. Connect one end of another network cable to the 10/100 DATA IN port on the Power over
Ethernet Injector.
8. Open your web browser, type the IP address of the access point in the address bar, and then
press Enter. The default IP address is 192.168.10.100.

4
9. Enter the User name and Password, and then click OK. By default:
User Name: admin
Password: admin
Note: Username and password are case sensitive.
Note: For first time installation, you are required to change the admin password.
10. Enter a new admin password.
11. Confirm the new password.
12. Click Save.
13. Please wait while the access point reboots.
14. Click Wireless " Virtual AP.
15. Click Edit.

Note: To protect your network from any unauthorized access it is recommended to enable
wireless encryption.
5
16. Select WPA2-PSK for security type.
17. Select AES for cipher suite.
18. Enter a Pre-shared Key (wireless password).
19. Click Save.
16
17
18
19

6
22. Wait 45 seconds while the Access Point reboots.
21. Click Reboot.
20. Click Reboot.
23. Configure the TEW-739APBO's IP address to a valid IP address within the subnet defined by
the Router. Avoid using an IP address within the DHCP pool of your router. In this example,
we will assume the following:
Router IP Address: 192.168.10.1
Subnet Mask: 255.255.255.0
DHCP Pool: 192.168.10.100~192.168.10.149
The TEW-739APBO will be setup with the following IP address assignment:
IP Address: 192.168.10.50
IP Netmask (Subnet Mask): 255.255.255.0
IP Gateway (Gateway IP Address): 192.168.10.1
Primary DNS: 192.168.10.1

7
24. Click System " LAN.
25. Select Static IP.
26. Configure the IP Address, IP Netmask and IP Gateway based on the example in step 23.
27. Select Specify DNS Server IP.
28. Configure the Primary DNS based on the example in step 23.
29. Click Save.
30. Click Reboot.
25
26
27
28
29
24
24

8
31. Click Reboot.
32. Wait 45 seconds while the Access Point reboots.

9
3. Hardware Installation
Waterproof kit installation
1. Unscrew the sealing nut from the main
body.
2. Separate the rubber seal from the claw.
Cable Gland Seal Claw Sealing Nut
3. Verify that you have the following parts:
Cable Gland, Seal, Claw, Sealing Nut
4. Insert one end of an Ethernet cable into
the sealing nut.
5. Insert the Ethernet cable into the seal.
6. Insert the seal into the claw.
7. Insert the seal/rubber claw into the Cable
Gland.
8. Connect the Ethernet cable to the PoE port
on the rear of the access point.
9. Using your hand, screw the main body
counter clockwise to secure it to the
TEW-739APBO.
10. Using your hand, screw the seal nut
counter clockwise to secure it to the main
body.