TRENDnet TEW-638APB User manual

TEW-638APB
3.02
Quick Installation Guide

Table of Contents
English 1
1. Before You Start 1
2. Hardware Installation 2
Version 04.04.2017

1. Before You Start
Package Contents
System Requirements
ŸTEW-638APB
ŸMulti-Language Quick Installation Guide
ŸCD-ROM (Utility and User's Guide)
ŸPower Adapter (12V DC, 0.5A)
ŸNetwork Cable (0.6m / 2ft.)
ŸWeb Browser: Internet Explorer (6 or higher), Firefox 2.0 or higher, Opera,
Chrome, Safari
ŸA computer with a network adapter or wireless adapter properly installed
ŸA router with an available network LAN port
ŸAn available DHCP Server – routers usually have a built-in DHCP server
Package Contents
System Requirements
1
ŸTEW-638APB
ŸMulti-Language Quick Installation Guide
ŸCD-ROM (Utility and User's Guide)
ŸPower Adapter (12V DC, 0.5A)
ŸNetwork Cable (0.6m / 2ft.)
ŸWeb Browser: Internet Explorer (6 or higher), Firefox 2.0 or higher, Opera,
Chrome, Safari
ŸA computer with a network adapter or wireless adapter properly installed
ŸA router with an available network LAN port
ŸAn available DHCP Server – routers usually have a built-in DHCP server

2. Hardware Installation
1. Insert Utility CD-ROM into your computer's
CD-ROM drive.
2. Click Run Setup.exe. (Windows 7/Vista only)
2
Note:
1. Locate an optimum location for the Access Point. The best place for the Access Point
is usually at the center of your wireless network.
2. Disable any anti-virus and firewall programs before starting hardware installation.
For Windows Users
3. Click Setup Wizard.
4. Click I accept the terms in the License
Agreement and then click Next.

3
5. Connect the provided network cable from a
LAN port on your Router to the LAN port on the
TEW-638APB. Then click Next.
6. Connect a network cable from a LAN port on
your Router to the Ethernet port on your
computer.
8. Select the TEW-638APB from the list and then
click Configure.
9. Enter a password and then click Login. The
default password is admin.
7. Connect the Power Adapter to the Access Point
and then to a power outlet. Then click Next.

4
10. Select Access Point and then click Next.
Note: For AP Client setup, please refer to the
User's Guide for step by step instructions.
The User's Guide can be found on this
product's CD-ROM.
11. Select Dynamic IP Address Configuration
and then click Configure.
12. Select Manual setup and then click Next.
13. Enter a SSID and then click Next. By default,
the SSID is TRENDnet638. Enter a SSID
(Wireless Network Name) and then click Next.
By default, the SSID is TRENDnet638. The
SSID is the wireless network name of your
wireless network (e.g. wireless router or
access point). Enter a unique SSID. Choose
something that you would easily identify when
searching for available wireless networks.

5
14. Select the desired Wireless Mode and then
click Next.
15. Select a Security Mode and then click Next.
Note:
1. To protect your network from any unauthorized access it is recommended to enable
wireless encryption.
2. The example below is for WPA2-PSK (AES) security. If you select WPA-PSK or
WPA2-PSK, make sure your wireless adapters support WPA or WPA2. If your
wireless adapters do not support WPA or WPA2, then select WEP.
3. WEP encryption only supports 802.11b/g speed of up to 54Mbps.
4. Once encryption is enabled on the router, each wireless computer and device must
be configured with the same encryption key.
16. Select the desired WPA mode, enter
characters for your Pre-Shared key and then
click Next. For WPA-PSK or WPA2-PSK, the
Pre-Shared Key must be between 8 and 63
ASCII or 64 HEX characters. Make sure to
copy down the Pre-Shared Key. You will need
the Pre-Shared Key when you configure your
wireless adapter(s).

6
18. Give the file a name, then click Save.
17. Click Save (optional). This saves your
configuration settings in a file, which can be
roloaded when needed.
19. Click Configure to apply the settings.
20. Click Exit.

7
Note: To connect a wireless computer to the TEW-638APB, please refer to the first
question in the troubleshooting section.
Your Installation is complete
For detailed information regarding the TEW-638APB’s configuration and advanced settings,
please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or
TRENDnet's website at http://www.trendnet.com.
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
21. Click Yes to exit.
22. Connect the 2dBi detachable antennas to the
TEW-638APB.

Product Information:
Product Name:
Model Number: TEW-638APB
Trade Name: TRENDnet
N300 Wireless Access Point
Manufacturer’s Name and Address
TRENDnet hereby declare that the product is in compliance with the essential requirements and
other relevant provisions under our sole responsibility.
This product is herewith confirmed to comply with the Directives.
Directives:
EMC:
Person responsible for this declaration.
Signature:
Date: April 04, 2017
Title: Director of Technology
Name: Sonny Su
Place of Issue: Torrance, California, USA
ETSI EN 301 489-17 V2.2.1 2012-09
ETSI EN 301 489-1 V1.9.2 2011-09
EN 55022: 2010/AC: 2011
EN 55024: 2010
EN 61000-3-2: 2014
EN 61000-3-3: 2013 IEC 61000-4-2: 2008
EN 61000-4-2: 2009 IEC 61000-4-3: 2006 + A1: 2007+ A2: 2010
EN 61000-4-3: 2006 + A1: 2008 + A2: 2010 IEC 61000-4-4: 2012
EN 61000-4-4: 2012 IEC 61000-4-5: 2005
EN 61000-4-5: 2006 IEC 61000-4-6: 2008
EN 61000-4-6: 2009 IEC 61000-4-8: 2009
EN 61000-4-11: 2004 IEC 61000-4-11: 2004
EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 + A2: 2013
IEC 60950-1: 2005 (2nd Edition) + Am 1: 2009 + Am 2:2013
Directive 2014/53/EU
Directive CEM 2004/108/EC et 2014/30/EU
Directive RoHS 2011/65/EU
REACH Réglement (CE) N° 1907/2006
TRENDnet, Inc.
20675 Manhattan Place
Torrance, CA 90501 USA
Zwolsestraat 156 2587 WB
The Hague The Netherlands