TRENDnet TEW-715APO User manual

TRenDnET
N150 Wireless Outdoor PoE Access Point
TEW-715AP0
• Quick Installation Guide (1)
TEW-715APO ( 1.0R) / 08.23.2012

PYCCKMM ESPAftol DEUTSCH 1 FRANQAIS ENGLISH
1. Before You St rt
P ck ge Contents Minimum Requirements
• TEW-71 APO • Computer with an Ethernet port and Web
• CD-ROM (User's Guide) Browser
• Multi-Language Quick Installation Guide • A network switch or router with an available
• PoE injector network LAN port
• Power cord • 2 x RJ-4 network cables
• Pole mounting clamp
• Grounding wire
Note: The TEW-71 APO does not support IEEE 802.3af. You must use the proprietary Power over
Ethernet injector that is supplied with the TEW-71 APO.
2. H rdw re Configur tion
Note:
1. The default IP address of the TEW-71 APO is 192.168.10.100. To configure the TEW-71 APO,
your network adapter must have an IP address within the 192.168.10.x subnet (e.g.
192.168.10. 0). Please refer to the Appendix in the User's Guide for more information.
2. Disable any anti-virus and firewall programs before configuring the access point.
1

Ph se 1: Configur tion
Note:
1. The initial configuration should be completed in a testing environment with the two
TEW-71 APO's approximately 1 ft. ( meters) apart from one another,
2. Configure and connect the devices before mounting.
TEW-71 APO
2
PYCCKMM I ESPAtiOL I DEUTSCH

PYCCKMM ESPAftol DEUTSCH 1 FRANQAIS ENGLISH
1. Write the MAC address of the two
TEW-71 APOs. The MAC address can be
found on the back of the unit.
3. Connect one end of a network cable into the
TEW-71 APO #1.
• Remove the bottom cover and connect a
network cable to the PoE port.
4. Connect the opposite end of the network
cable to the POE port on the Power over
Ethernet Injector.
. Connect one end of another network cable to
the LAN port on the Power over Ethernet
Injector.
6. Connect the other end of a network cable to
your computer's Ethernet port.
7. Connect the power adapter into the Power
over Ethernet Injector. Then connect the
power adapter into a power outlet.
8. Assign a Static IP address to your computer's
network adapter in the subnet of
192.168.10.x (e.g. 192.168.10.2 ) and a
subnet mask of 2 .2 .2 .0.
9. Open your web browser, type the IP address
of the access point in the address bar, and
then press Enter. The default IP address is
192.168.10.100
10. Enter the User name and Password, and
then click Login. By default:
User Name: admin
Password: admin
Note: User Name and Password are case
sensitive.
11. Click Wireless and then click Basic
Settings.
• Basic Settings '
• Profile Settings
• Advanced Settin
• WDS Settings
12. Select Bridge for Operation Mode.
13. Click Apply.
3

14. Click OK.
Change settings
1 . Click Wireless and then click WDS
Settings.
16. Click Enabled for WDS Separation.
17. Enter the MAC address of the
TEW-71 APO that you are connecting to.
18. Click Apply.
19. Click OK.
20. Please refer to the user manual for the
steps in setting up wireless encryption.
Note: To protect your network from any
unauthorized access it is recommended to
enable wireless encryption.
21. Click B ck.
*
22. Click System and then click Network
Settings.
System Settings
Network Settings
• Time Settings
' ADIUS Settings
23. Select Use Fixed IP Address.
24. Configure the TEW-71 APO's IP address to
a valid IP address within the subnet defined
by the Router. Avoid using an IP address
within the DHCP pool of your router. In this
example, we will assume the following:
Router IP Address: 192.168.10.1
Subnet Mask: 2 .2 .2 .0
DHCP Pool:
192.168.10.100~192.168.10.199
The TEW-71 APO will be setup with the
following IP address assignment:
IP Address: 192.168.10.200
Subnet Mask: 2 .2 .2 .0
Gateway IP Address: 192.168.10.1
DNS 1: 192.168.10.1
4
p y c c & »1 ESPAt L DEUTSCH 1 FRAM^AiS ENGLISH

PYCCKMM ESPAftol DEUTSCH 1 FRANQAIS ENGLISH
25. Click Apply.
26. Click OK.
27. Repeat steps 2-26 for TEW-71 APO #2.
Ph se 2: Confirm Connectivity
Note:
1. Leave TEW-71 APO #2 connected to your computer,
2. Connect TEW-71 APO #1 to a LAN port of a router on your network.
3. To verify connectivity, run your computer's command prompt and ping TEW-71 APO #1's
assigned IP address from your computer.
4. A successful ping reply determines that both TEW-71 APOs are configured properly and
connected.
5

3. H rdw re Inst ll tion
Building 1
6
Building 2
ESPAtiOL I DEUTSCH

PYCCKMM ESPAftol DEUTSCH 1 FRANQAIS ENGLISH
1. Refer to the above diagram.
2. Mount the TEW-71 APOs in your desired location. See Pole Mounting the TEW-71 APO for
mounting instructions.
3. Connect the TEW-71 APOs to their respective network.
4. Confirm that the TEW-71 APOs are facing each other,
. Verify that the status LED indicators on both TEW-71 APOs are fully functional: Power
(Solid/Green), LAN (Blinking/Green) and Signal Indicator [Wireless] (Green, Yellow or Red).
Connecting the Grounding Wire
1. Loosen and remove the metal O-ring on the N-type connector,
2. Put the grounding wire into the connector and tighten up with the O-ring.
3. Connect the grounding wire to a grounding object. e.g. Earth driven rod or grounded electrical
system.
7

Pole Mounting the TEW-715APO
Note:
The pole mounting clamp supports poles with
a maximum diameter of 63mm (2.48 inches).
1. Turn the screw on the pole mounting
clamp counter clockwise.
2. Insert the pole mounting clamp through the
middle of the TEW-71 APO.
A
3. Wrap the mounting clamp around a pole.
4. Secure the TEW-71 APO to pole by turning
the screw clockwise.
Wireless outdoor access point installation is
now complete.
For detailed information regarding the
TEW-71 APO's configuration and advanced
settings and mounting instructions, please refer
to the User's Guide on the provided CD-ROM.
8

Declaration of Conformity TREflDnET
Company Information:
Company Name:
T ENDnet, Inc.
Company Address:
20675 Manhattan Place
Torrance, CA 90501
USA
Product Information:
Product Description:
N150 Wireless Outdoor PoE Access Point
Model Number:
TEW-715APO
Brand name:
T ENDnet
Technical Standards:
EN 300 328 Vl.7.1:10-2006
EN 301489-1 Vl.9.2:09-2011
EN 301 489-17 V2.1.1:09-2011
EN 50385 : 2002
EN 60950-1: 2006 + A l l : 2009 + A 1 : 2010 + A12 : 2011
Declaration:
on th e ra d io a nd te le co mmu n ica tio n s te rm in a l e q uip m e nt a nd En e rgy -re la te d p ro d u cts Dir ectiv e 200 9/12 /EC.
I h e re b y d e cla re tha t the p ro d u cts an d d e v ic es me ntio ne d a bo ve a re c o n sis te nt with the s ta n d a rd s a nd p r o v isio ns o f th e
guidelines.
Th e p ro d u c t i s h e re with c on firme d t o c o mp ly with t h e re q u ire m e n ts of Dir e ctiv e 1 9 9 9 / /E C o f t h e Cou nc il (E u ro p e a n Pa rliam e n t)
Sonny Su Director of Technology
Full Name Position/Title
July 16,2012
Date