TRENDnet TEW-740APBO2K User manual

Quick Installation Guide
TEW-740APBO2K

Table of Content
1 English
1. Before You Start
2. Hardware Setup and Configuration
3. Ground Wire and Pole Mount Installation

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
1
1. Before You Start
Note:
It is recommended to use network cables without additional caps, molded caps, or boots with
the access points for cable fitment inside the enclosure.
Note:
The TEW-740APBO does not support IEEE 802.3at/af PoE standards. You must use the
proprietary Power over Ethernet injector that is supplied with the TEW-740APBO. The RJ-45
Ethernet cable between the passive PoE injector and access point can have a maximum length
of up to 60 m (197 ft.).
Package Contents
Ÿ2 x TEW-740APBO
ŸCD-ROM (User's Guide)
ŸQuick Installation Guide
ŸProprietary PoE injectors
ŸPower adapters (12 V DC, 1A)
ŸMounting Hardware
ŸGrounding wires
Minimum Requirements
ŸComputer with a network port and web browser
ŸA network switch or router with an available network LAN port
ŸPhillips screwdriver (Ground wire installation)
Ÿ4 x RJ-45 network cables

2
2. Hardware Setup and Configuration
Note: By default, the TEW-740APBO access points are preconfigured to establish a point-to-
point WDS bridge between each other using a unique predefined AES encryption key. For
convenience, a unique predefined admin password has already been assigned to both access
points. You can find the preconfigured access point settings on the wireless sticker or on the
device label beneath the cover where the Ethernet ports and LEDs are located. No additional
configuration is required.
WIFI MAC: XXXXXXXXXXXXXXXXX
ETH LAN1 MAC: XXXXXXXXXXXXXXXXX
Model: TEW-740APBO / A
S/N: XXXXXXXXXXXXXXX
H/W: V2.0R FW: 2.0K
Made in XXXXXXX
IP Address: 192.168.10.50
Subnet Mask: 255.255.255.0
User Name: admin
Passwork: XXXXXXXX
Preset
Wireless Settings
Mode/WiFi Channel
WDS Bridge / CH 1
AES Encryption Key
Management Login
http://192.168.10.51
username: admin
password: XXXXXXXX
740XXXXXXXX
Unit 1 Unit 2
Preset
Wireless Settings
Mode/WiFi Channel
WDS Bridge / CH 1
AES Encryption Key
Management Login
http://192.168.10.50
username: admin
password: XXXXXXXX
740XXXXXXXX

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
3
1. Remove the cover of the access point by pushing and holding the tab in the vertical direction
upward (based on the access point orientation below) and pulling the cover in the two
locations noted below away from the access point.
Pull and hold tab
Aside from the preconfigured WDS bridge settings, the TEW-740APBO access points will also be
configured with the following default settings:
Verify connectivity between the two access points before mounting.
TEW-740APBO #1
Mode: WDS Mode
IP Address: 192.168.10.50
Netmask (Subnet Mask): 255.255.255.0
IP Gateway (Default Gateway): 192.168.10.1
Primary DNS: 192.168.10.1
TEW-740APBO #2
Mode: WDS Mode
IP Address: 192.168.10.51
Netmask (Subnet Mask): 255.255.255.0
IP Gateway (Default Gateway): 192.168.10.1
Primary DNS: 192.168.10.1

4
2. Remove the tab on the far left by gently bending it back and forth until the tab is removed.
This will create the opening for a RJ-45 network cable to be routed through.
Tab
3. Using a network cable, connect one end of the cable to the LAN (PoE) port and push the cable
into the cable guide on the far left, then through the opening that was created in the previous
step.
Cable Guide

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
5
4. Connect the other end of the network cable to the P+DATA OUT port on the included PoE
injector.
5. Connect the included power adapter to the PoE injector POWER IN on the included PoE
injector.
6. Plug the connected power adapter into a power outlet.
7. Confirm the device is powered on through the LED indicators.
8. Assign a static IP address to your computer's network adapter in the subnet of 192.168.10.x
(e.g. 192.168.10.10) and subnet mask of 255.255.255.0.
9. Using another network cable, connect one end to the 10/100 DATA IN port on the included
PoE injector for either the first or second access point.
10. Connect the other end of the network cable to your computer's Ethernet port.
Note: Repeat Steps 1-7 to power on and connect the second access point.
Included PoE Injector
LAN1 (PoE)
P+DATA OUT
POWER IN 10/100Mbps DATA IN

6
12. To verify connectivity on your computer, open a command prompt or terminal application
window and type in the following commands.
11. Make sure both access points are powered on approximately 15 ft. (5 m) apart from one
another with front of access points directly facing each other.
15 ft. (5m)
LAN1 (PoE)
P+DATA OUT
POWER IN
P+DATA OUT
10/100Mbps DATA IN
TEW-740APBO #1 TEW-740APBO #2
LAN1 (PoE)
POWER IN

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
7
A successful connectivity test will appear similar to the result below for each access point. Ping
replies and 0% packet loss will indicate a successful point to point bridge connection between
the two access points.
Note: If the connectivity test fails, wait for about a minute and try again. Make sure there are no
obstacles between the two access points when running the connectivity test and make sure the
two access points are not too close together.
® ®
Note: In Windows , you can use the Command Prompt application and in Mac , you can
Terminal application to run the commands for connectivity testing.
ping 192.168.10.50
<Press Enter and wait for result>
ping 192.168.10.51
<Press Enter and wait for result>

8
3. Ground Wire and Pole Mount Installation
1. Locate the grounding point located in the bottom section of the enclosure. Using a Phillps
screwdriver, remove the grounding point screw (counter clockwise) and attach the included
grounding wire to the grounding point screw. Then reattach the ground screw (clockwise)
along with the grounding wire. After installing the grounding wire, remove another tab on the
enclosure by gently bending back and forth until the tab is removed. This will create the
opening for the ground cable to be routed through.
Note: The ground wire may need to be cut and extended using additional ground wire in order
to reach a proper grounding point.
Tab
Grounding point

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
9
2. Reinstall the cover by lining up the guides into the notches as shown and push the cover
down until the cover clips in and is secured.
3. Insert the included fasteners through the holes located at the back of the access point.
4. Wrap the fasteners around the pole where the access points will be installed. On the
fasteners, insert the open end into the locking mechanism and pull tight until the access
point is secured.
5. After the access points are properly mounted, you can connect the grounding wires to the
proper ground points and RJ-45 cables from each access point to your network.

Quick Installation Reference
10
Building 1 Building 2
Internet
Modem
Router

Product Information:
Product Name:
Model Number: TEW-740APBO / TEW-740APBO2K
Trade Name: TRENDnet
10 dBi Wireless N300 Outdoor PoE Access Point /
10 dBi Wireless N300 Outdoor PoE Preconfigured Point-to-Point Bridge Kit
Manufacturer’s Name and Address
Directives: Low Voltage Directive 2014/35/EU
EMC Directive 2014/30/EU
RED Directive 2014/53/EU
RoHS Directive 2011/65/EU
REACH Regulation (EC) No. 1907/2006
TRENDnet hereby declare that the product is in compliance with the essential requirements and
other relevant provisions under our sole responsibility.
This product is herewith confirmed to comply with the Directives.
EN 300 328 V1.9.1: 02-2015
EN 62311: 2008
Safety EN 60950-1: 2006 + A11: 2010 + A12: 2011 + A2: 2013
EMC EN 301 489-1 V1.9.2: 09-2011
EN 301 489-17 V2.2.1: 09-2012
EN 55024: 2010 + A1: 2015
EN 55032: 2015
Radio Spectrum & Health
Note:
This device is designed to provide uninterrupted operation. This device does not offer power
management functionality such as Off mode or Standby mode.
Regulation (EC) No. 1275/2008, No. 801/2013
Energy Efficiency
TRENDnet, Inc.
20675 Manhattan Place
Torrance, CA 90501 USA
Zwolsestraat 156 2587 WB
The Hague The Netherlands
Date: February 14, 2017
Title: Director of Technology
Person responsible for this declaration.
Place of Issue: Torrance, California, USA
Name: Sonny Su
Signature:

Certifications
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received.
Including interference that may cause undesired operation.
TRENDnet
20675 Manhattan Place
Torrance, CA 90501
USA
Applies to PoE Products Only: This product is to be connected
only to PoE networks without routing to the outside plant.
Note
The Manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority
to operate the equipment.
Advertencia
En todos nuestros equipos se mencionan claramente las
caracteristicas del adaptador de alimentacón necesario para
su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo
conectado. El adaptador de alimentación debe operar con
voltaje y frecuencia de la energia electrica domiciliaria exitente
en el pais o zona de instalación.
Product Warranty Registration
Please take a moment to register your
product online. Go to TRENDnet’s website at:
www.trendnet.com/register
Technical Support
If you have any questions regarding the product
installation, please contact our Technical Support.
Toll free US/Canada: 1-866-845-3673
Regional phone numbers available
at www.trendnet.com/support
Waste electrical an electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or Retailer for recycling advice.
Copyright © 2017. All Rights Reserved. TRENDnet. TEW-740APBO2K(V2) / 02.14.2017