Tyco TY-L Series User manual

General
Description
The Series TY-L, 5.6 and 8.0 K-factor,
Upright and Pendent Sprinklers de-
scribed in this data sheet are standard
response - standard coverage, solder
type spray sprinklers designed for use
in light, ordinary, and extra hazard,
commercial occupancies such as
banks, hotels, shopping malls, facto-
ries, refineries, chemical plants, etc.
The recessed version of the Series
TY-L Pendent Sprinkler, where appli-
cable, is intended for use in areas with
a finished ceiling. It uses a two-piece
Style 20 (1/2 inch NPT) or Style 30 (3/4
inch NPT) Recessed Escutcheon. The
Recessed Escutcheon provides 1/4
inch (6,4 mm) of recessed adjustment
or up to 1/2 inch (12,7 mm) of total
adjustment from the flush pendent po-
sition. The adjustment provided by the
Recessed Escutcheon reduces the ac-
curacy to which the fixed pipe drops to
the sprinklers must be cut.
Corrosion resistant coatings, where
applicable, are utilized to extend the
life of copper alloy sprinklers beyond
that which would otherwise be ob-
tained when exposed to corrosive at-
mospheres. Although corrosion resis-
tant coated sprinklers have passed the
standard corrosion tests of the appli-
cable approval agencies, the testing is
not representative of all possible cor-
rosive atmospheres. Consequently, it
is recommended that the end user be
consulted with respect to the suitability
of these coatings for any given corro-
sive environment. The effects of ambi-
ent temperature, concentration of
chemicals, and gas/chemical velocity,
should be considered, as a minimum,
along with the corrosive nature of the
chemical to which the sprinklers will be
exposed.
An intermediate level version of the
Series TY-L Pendent Sprinkler can be
obtained by utilizing the Series TY-L
Pendent Sprinkler in combination with
the Model S Shield.
WARNINGS
The Series TY-L Sprinklers described
herein must be installed and main-
tained in compliance with this docu-
ment, as well as with the applicable
standards of the National Fire Protec-
tion Association, in addition to the
standards of any other authorities hav-
ing jurisdiction. Failuretodosomay
impair the performance of these de-
vices.
The owner is responsible for maintain-
ing their fire protection system and de-
vices in proper operating condition.
The installing contractor or sprinkler
manufacturer should be contacted
with any questions.
Model/Sprinkler
Identification
Numbers
TY3111 - Upright 5.6K, 1/2"NPT
TY3211 - Pendent 5.6K, 1/2"NPT
TY4111 - Upright 8.0K, 3/4"NPT
TY4211 - Pendent 8.0K, 3/4"NPT
TY4811 - Upright 8.0K, 1/2"NPT
TY4911 - Pendent 8.0K, 1/2"NPT
TY3111 is a redesignation for S1800
and G3111.
TY3211 is a redesignation for S1801
and G3112.
TY4111 is a redesignation for S1810
and G3101.
TY4211 is a redesignation for S1811
and G3102.
TY4811 is a redesignation for S1805.
TY4911 is a redesignation for S1806
Page 1 of 8 TFP110
JULY, 2004
Series TY-L — 5.6 and 8.0 K-factor
Upright, Pendent, and Recessed Pendent Sprinklers
Standard Response, Standard Coverage
Technical Services: Tel: [phone] / Fax: [phone]
IMPORTANT
Always refer to Technical Data
Sheet TFP700 for the “INSTALLER
WARNING” that provides cautions
with respect to handling and instal-
lation of sprinkler systems and com-
ponents. Improper handling and in-
stallation can permanently damage
a sprinkler system or its compo-
nents and cause the sprinkler to fail
to operate in a fire situation or cause
it to operate prematurely.

Page2of8 TFP110
(66,7 mm)
2-5/8"
NOMINAL
(11,1 mm)
UPRIGHT
MAKE-IN
7/16"
PENDENT
(50,8 mm)
(66,7 mm)
2-5/8"
2"
FLANGES
WRENCH
NPT
1/2"
SURFACE
PLATE SEATING
ES
C
UT
C
HE
O
N
CROSS SECTIONRECESSED PENDENT
2-7/8" (73,0 mm) DIA.
AREA
WRENCH
3
RECESSED
ESCUTCHEON
STYLE 20
7
5
6
4
2
1
FIGURE 1
STANDARD RESPONSE SERIES TY-L UPRIGHT (TY3111) AND PENDENT (TY3211) SPRINKLERS
5.6 K-FACTOR, 1/2 INCH NPT
1-Frame
2-Sealing
Button
3 - Ejection
Spring
4-Fusible
Element
5-Strut
6-Hook
7-Deflector *Temperature rating is indicated on deflector.
**Pipe thread connections per ISO 7/1 can be provided on
special request.
(12,7 mm)
NOMINAL
2-11/16"
(68,3 mm)
UPRIGHT
MAKE-IN
1/2"
PENDENT
2-11/16"
(68,3 mm)
(50,8 mm)
2"
WRENCH
FLANGES
3/4"
NPT
ES
C
UT
C
HE
O
N
PLATE SEATING
SURFACE
CROSS SECTION
2-7/8" (73,0 mm) DIA.
RECESSED PENDENT
3
STYLE 30
ESCUTCHEON
RECESSED
7
6
5
4
2
1
AREA
WRENCH
FIGURE 2
STANDARD RESPONSE SERIES TY-L UPRIGHT (TY4111) AND PENDENT (TY4211) SPRINKLERS
8.0 K-FACTOR, 3/4 INCH NPT
1-Frame
2-Sealing
Button
3-Ejection
Spring
4-Fusible
Element
5-Strut
6-Hook
7 - Deflector *Temperature rating is indicated on deflector.
**Pipe thread connections per ISO 7/1 can be provided on
special request.

Technical
Data
Approvals
UL and C-UL Listed.
FM, and LPCB Approved.
(Refer to Table A for complete approval
information including corrosion resis-
tant status.)
Maximum Working Pressure
175 psi (12,1 bar)
Discharge Coefficient
K=5.6GPM/psi
1/2 (80,6 LPM/bar1/2)
K=8.0GPM/psi
1/2 (115,2 LPM/bar1/2)
Temperature Ratings
RefertoTableA
Finishes
Sprinkler: Refer to Table A
Recessed Escutcheon: White Coated,
Chrome Plated, or Brass Plated
Physical Characteristics
Frame..............Brass
Sealing Button . . Bronze w/Teflon†
Ejection Spring . . . . Stainless Steel
Fusible Element . . . Solder, Copper
............StainlessSteel
Strut ..............Monel
Hook ......... Bronze/Monel
Deflector ........... Bronze
† DuPont Registered Trademark
Operation
A copper tube sealed by two stainless
steel balls holds a fusible alloy. When
the rated temperature is reached, the
alloy melts, the balls are forced toward
each other releasing the tension
mechanism, allowing the sprinkler to
operate.
Design
Criteria
The Series TY-L Pendent and Upright
Sprinklers are intended for fire protec-
tion systems designed in accordance
with the standard installation rules rec-
ognized by the applicable Listing or
Approval agency (e.g., UL Listing is
based on the requirements of NFPA
13, and FM Approval is based on the
requirements of FM’s Loss Prevention
Data Sheets). Only the Style 20 or 30
Recessed Escutcheon, as applicable,
is to be used for recessed pendent
installations.
Installation
TheSeriesTY-LSprinklersmustbe
installed in accordance with the follow-
ing instructions:
NOTES
A leak tight 1/2 inch NPT sprinkler joint
should be obtained with a torque of 7
to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi-
mum of 21 ft. lbs. (28,5 Nm) of torque
may be used to install sprinklers with
1/2 NPT connections. A leak tight 3/4
inch NPT sprinkler joint should be ob-
tained with a torque of 10 to 20 ft.lbs.
(13,4 to 26,8 Nm). A maximum of 30
ft.lbs. (40,7 Nm) of torque is to be used
to install sprinklers with 3/4 NPT con-
nections. Higher levels of torque may
distort the sprinkler inlet and cause
leakage or impairment of the sprinkler.
Do not attempt to make-up for insuffi-
cient adjustment in the escutcheon
plate by under- or over-tightening the
sprinkler. Readjust the position of the
sprinkler fitting to suit.
The Series TY-L Pendent and Up-
right Sprinklers must be installed in
accordance with the following instruc-
tions.
Step 1. Pendent sprinklers are to be
installed in the pendent position, and
upright sprinklers are to be installed in
the upright position.
Step 2. With pipe thread sealant ap-
plied to the pipe threads, hand tighten
the sprinkler into the sprinkler fitting.
TFP110 Page 3 of 8
(66,7 mm)
2-5/8"
NOMINAL
(11,1 mm)
UPRIGHT
MAKE-IN
7/16"
PENDENT
(50,8 mm)
(66,7 mm)
2-5/8"
2"
FLANGES
WRENCH
NPT
1/2"
SURFACE
PLATE SEATING
ES
C
UT
C
HE
O
N
CROSS SECTIONRECESSED PENDENT
2-7/8" (73,0 mm) DIA.
3
RECESSED
ESCUTCHEON
STYLE 20
7
5
6
4
2
1
AREA
WRENCH
FIGURE 3
STANDARD RESPONSE SERIES TY-L UPRIGHT (TY4811) AND PENDENT (TY4911) SPRINKLERS
8.0 K-FACTOR, 1/2 INCH NPT
1-Frame
2-Sealing
Button
3 - Ejection
Spring
4-Fusible
Element
5-Strut
6-Hook
7-Deflector *Temperature rating is indicated on deflector.
**Pipe thread connections per ISO 7/1 can be provided on
special request.

Page4of8 TFP110
TYPE TEMP.
RATING
FRAME
COLOR
CODE
NATURAL
BRASS
CHROME
PLATED
SPRINKLER FINISH
RECESSED PENDENT
(TY3211 w/ Style 20)
NOTES:
1. Listed by Underwriters Laboratories, Inc. (UL).
2. Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL).
3. Approved by Factory Mutual Research Corporation (FM).
4. Approved by Factory Mutual Research Corporation (FM) for maximum 150°F/68°C ambient temperatures.
5. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/03).
N/A: Not Available
TABLE A
LABORATORY LISTINGS AND APPROVALS
WAX OVER
LEAD COATED
LEAD
COATED
WAX
COATED
N/A
41, 2
5.6
1/2"
NPT
PENDENT (TY3211)
and
UPRIGHT (TY3111)
165°F/74°C Unpainted
212°F/100°C White
280°F/138°C Blue
1, 2, 3, 5
K
1, 2, 3
N/A
1, 2, 3, 5
165°F/74°C Unpainted
212°F/100°C White 1, 2, 3, 5
TYPE TEMP.
RATING
FRAME
COLOR
CODE
NATURAL
BRASS
CHROME
PLATED
SPRINKLER FINISH
WAX OVER
LEAD COATED
LEAD
COATED
WAX
COATED
K
8.0
3/4"
NPT
PENDENT (TY4211)
and
UPRIGHT (TY4111)
RECESSED PENDENT
(TY4211 w/ Style 30)
165°F/74°C Unpainted
212°F/100°C White
280°F/138°C Blue
165°F/74°C Unpainted
212°F/100°C White
1, 2, 3, 5
1, 2, 3
1, 2 4N/A
N/A
1, 2, 5
TYPE TEMP.
RATING
FRAME
COLOR
CODE
NATURAL
BRASS
CHROME
PLATED
SPRINKLER FINISH
WAX OVER
LEAD COATED
LEAD
COATED
WAX
COATED
K
8.0
1/2"
NPT
PENDENT (TY4911)
and
UPRIGHT (TY4811)
RECESSED PENDENT
(TY4911 w/ Style 20)
165°F/74°C Unpainted
212°F/100°C White
280°F/138°C Blue
165°F/74°C Unpainted
212°F/100°C White
1, 2, 3, 5
1, 2, 3
1, 2 N/A
N/A
1, 2

Step 3. Tighten the sprinkler into the
sprinkler fitting using only the W-Type
9 Sprinkler Wrench (Ref. Figure 7),
except that an 8 or 10 inch adjustable
Crescent wrench is to be used for wax
coated sprinklers. With reference to
Figures 1, 2, and 3, the W-Type 9
Sprinkler Wrench is to be applied to
the wrench area, or as applicable, the
adjustable Crescent wrench is to be
applied to the wrenching flanges.
When installing wax coated sprinklers
with the adjustable Crescent wrench,
additional care needs to be exercised
to prevent damage to the wax coating
on the sprinkler wrench flats or frame
arms and, consequently, exposure of
bare metal to the corrosive environ-
ment. The jaws of the wrench should
be opened sufficiently wide to pass
over the wrench flats without damag-
ing the wax coating. Before wrench
tightening the sprinkler, the jaws of the
wrench are to be adjusted to just con-
tact the sprinkler wrench flats. After
wrench tightening the sprinkler, loosen
the wrench jaws before removing the
wrench.
After installation, the sprinkler wrench
flatsandframearmsmustbein-
spected and the wax coating re-
touched (repaired) whenever the coat-
TFP110 Page 5 of 8
FIGURE 4
SERIES TY-L (TY3211) RECESSED PENDENT SPRINKLER ASSEMBLY
WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 20 RECESSED ESCUTCHEON
5.6 K-FACTOR, 1/2 INCH NPT
(11,1±3,2 mm)
SURFACE
CLOSURE
SPRINKLER
MOUNTING
FACE OF
FITTING
7
/
16±1
/
8"
1/4" (6,4 mm)
(73,0 mm)
TY-L
2-1/4" DIA.
(57,2 mm)
1-1/2" (38,1 mm)
PLATE
MOUNTING
(3,2 mm)
1-3/4" (44,5 mm)
1/8"
2-7
/
8" DIA. 1/2" (12,7 mm)
FIGURE 5
SERIES TY-L (TY4211) RECESSED PENDENT SPRINKLER ASSEMBLY
WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 30 RECESSED ESCUTCHEON
8.0 K-FACTOR, 3/4 INCH NPT
SPRINKLER
FACE OF
FITTING
SURFACE
MOUNTING
1/8"
(3,2 mm)
1-1/2" (38,1 mm)
1-3/4" (44,5 mm)
1/4" (6,4 mm)
1/2" (12,7 mm)
CLOSURE
PLATE
MOUNTING
TY-L
(57,2 mm)
2-1/4" DIA.
(73,0 mm)
2-7
/
8" DIA.
(11,1±3,2 mm)
7
/
16±1
/
8"
FIGURE 6
SERIES TY-L (TY4911) RECESSED PENDENT SPRINKLER ASSEMBLY
WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 20 RECESSED ESCUTCHEON
8.0 K-FACTOR, 1/2 INCH NPT
(11,1±3,2 mm)
SURFACE
CLOSURE
SPRINKLER
MOUNTING
FACE OF
FITTING
7
/
16±1
/
8"
1/4" (6,4 mm)
(73,0 mm)
TY-L
2-1/4" DIA.
(57,2 mm)
1-1/2" (38,1 mm)
PLATE
MOUNTING
(3,2 mm)
1-3/4" (44,5 mm)
1/8"
2-7
/
8" DIA. 1/2" (12,7 mm)
RECESS
WRENCH
RECESS
WREN
C
H
FIGURE 7
W-TYPE 9 SPRINKLER
WRENCH
FIGURE 8
W-TYPE 10 RECESSED
SPRINKLER WRENCH

ing has been damaged and bare metal
is exposed. The wax coating on the
wrench flats can be retouched by gen-
tly applying a heated 1/8 inch diameter
steel rod to the areas of wax that have
been damaged, to smooth it back over
areas where bare metal is exposed.
NOTES
Only retouching of the wax coating ap-
plied to the wrench flats and frame
arms is permitted, and the retouching
is to be performed only at the time of
the initial sprinkler installation.
The steel rod should be heated only to
the point at which it can begin to melt
the wax, and appropriate precautions
need to be taken, when handling the
heated rod, in order to prevent the
installer from being burned.
If attempts to retouch the wax coating
with complete coverage are unsuc-
cessful, additional wax can be ordered
in the form of a wax stick (the end of
which is color coded). Only the correct
color coded wax is to be used, and
retouching of wrench flats and frame
arms is only permitted at the time of
initial sprinkler installation. With the
steel rod heated as previously de-
scribed, touch the rod to the area re-
quiring additional wax with the rod an-
gled downward, and then touch the
wax stick to the rod approximately
one-half inch away from the area re-
quiring retouching. The wax will melt
and run down onto the sprinkler.
The Series TY-L Recessed Pendent
Sprinklers must be installed in ac-
cordance with the following instruc-
tions.
Step A. After installing the Style 20 or
30 Mounting Plate, as applicable, over
the sprinkler threads and with pipe
thread sealant applied to the pipe
threads, hand tighten the sprinkler into
the sprinkler fitting.
Step B. Tighten the sprinkler into the
sprinkler fitting using only the W-Type
10 Recessed Sprinkler Wrench (Ref.
Figure 8). With reference to Figure 1,
2, or 3, the W-Type 10 Recessed Sprin-
kler Wrench is to be applied to the
sprinkler wrenching flanges.
Step C. After the ceiling has been in-
stalled or the finish coat has been ap-
plied, slide on the Style 20 or 30 Clo-
sure over the Series TY-L Sprinkler
and push the Closure over the Mount-
ing Plate until its flange comes in con-
tact with the ceiling.
Care and
Maintenance
TheSeriesTY-LSprinklersmustbe
maintained and serviced in accord-
ance with the following instructions:
NOTES
Before closing a fire protection system
main control valve for maintenance
work on the fire protection system that
it controls, permission to shut down the
affected fire protection system must be
obtained from the proper authorities
and all personnel who may be affected
by this action must be notified.
Absence of an escutcheon, which is
used to cover a clearance hole, may
delay the time to sprinkler operation in
a fire situation.
Sprinklers that are found to be leaking
or exhibiting visible signs of corrosion
must be replaced.
Automatic sprinklers must never be
painted, plated, coated or otherwise
altered after leaving the factory. Modi-
fied or over-heated sprinklers must be
replaced.
Care must be exercised to avoid dam-
age to the sprinklers - before, during,
and after installation. Sprinklers dam-
aged by dropping, striking, wrench
twist/slippage, or the like, must be re-
placed.
Frequent visual inspections are rec-
ommended to be initially performed for
corrosion resistant coated sprinklers,
after the installation has been com-
pleted, to verify the integrity of the cor-
rosion resistant coating. Thereafter,
annual inspections per NFPA 25
should suffice; however, instead of in-
specting from the floor level, a random
sampling of close-up visual inspec-
tions should be made, so as to better
determine the exact sprinkler condi-
tion and the long term integrity of the
corrosion resistant coating, as it may
be affected by the corrosive conditions
present.
The owner is responsible for the in-
spection, testing, and maintenance of
their fire protection system and de-
vices in compliance with this docu-
ment, as well as with the applicable
standards of the National Fire Protec-
tion Association (e.g., NFPA 25), in
addition to the standards of any other
authorities having jurisdiction. The in-
stalling contractor or sprinkler manu-
facturer should be contacted relative to
any questions.
It is recommended that automatic
sprinkler systems be inspected,
tested, and maintained by a qualified
Inspection Service in accordance with
local requirements and/or national
codes.
Limited
Warranty
Products manufactured by Tyco Fire
Products are warranted solely to the
original Buyer for ten (10) years
against defects in material and work-
manship when paid for and properly
installed and maintained under normal
use and service. This warranty will ex-
pire ten (10) years from date of ship-
ment by Tyco Fire Products. No war-
ranty is given for products or
components manufactured by compa-
nies not affiliated by ownership with
Tyco Fire Products or for products and
components which have been subject
to misuse, improper installation, corro-
sion, or which have not been installed,
maintained, modified or repaired in ac-
cordance with applicable Standards of
the National Fire Protection Associa-
tion, and/or the standards of any other
Authorities Having Jurisdiction. Mate-
rials found by Tyco Fire Products to be
defective shall be either repaired or
replaced, at Tyco Fire Products’ sole
option. Tyco Fire Products neither as-
sumes, nor authorizes any person to
assume for it, any other obligation in
connection with the sale of products or
parts of products. Tyco Fire Products
shall not be responsible for sprinkler
system design errors or inaccurate or
incomplete information supplied by
Buyer or Buyer’s representatives.
IN NO EVENT SHALL TYCO FIRE
PRODUCTS BE LIABLE, IN CON-
TRACT, TORT, STRICT LIABILITY OR
UNDER ANY OTHER LEGAL THE-
ORY, FOR INCIDENTAL, INDIRECT,
SPECIAL OR CONSEQUENTIAL
DAMAGES, INCLUDING BUT NOT
LIMITED TO LABOR CHARGES, RE-
GARDLESS OF WHETHER TYCO
FIRE PRODUCTS WAS INFORMED
ABOUT THE POSSIBILITY OF SUCH
DAMAGES,ANDINNOEVENT
SHALL TYCO FIRE PRODUCTS’ LI-
ABILITY EXCEED AN AMOUNT
EQUAL TO THE SALES PRICE.
THE FOREGOING WARRANTY IS
MADE IN LIEU OF ANY AND ALL
OTHER WARRANTIES EXPRESS OR
IMPLIED, INCLUDING WARRANTIES
OF MERCHANTABILITY AND FIT-
NESS FOR A PARTICULAR PUR-
POSE.
Page6of8 TFP110

Ordering
Procedure
When placing an order, indicate the full
product name. Refer to the Price List
for complete listing of Part Numbers.
Contact your local distributor for avail-
ability.
Sprinkler Assemblies with NPT
Thread Connections:
Specify: (Specify Model/SIN), Stand-
ard Response, (specify K-factor),
(specify temperature rating), Series
TY-L (specify Pendent or Upright)
Sprinkler with (specify type of finish or
coating), P/N (specify from Table B).
Recessed Escutcheon:
Specify: Style (specify) Recessed Es-
cutcheon with (specify finish), P/N
(specify).
1/2" (15 mm)
Style 20
Chrome Plated . . . . . . . . . P/N 56-705-9-010
1/2" (15 mm)
Style 20
White Color
Coated . . . . . . . . . . . . . . . P/N 56-705-4-010
1/2" (15 mm)
Style 20
Brass Plated . . . . . . . . . . . P/N 56-705-2-010
3/4" (20 mm)
Style 30
Chrome Plated . . . . . . . . . P/N 56-705-9-011
3/4" (20 mm)
Style 30
White Color
Coated . . . . . . . . . . . . . . . P/N 56-705-4-011
3/4" (20 mm)
Style 30
Brass Plated . . . . . . . . . . . P/N 56-705-2-011
Sprinkler Wrench:
Specify: W-Type 9 Sprinkler Wrench,
P/N 56-000-1-849.
Specify: W-Type 10 Sprinkler Wrench,
P/N 56-000-1-948.
Wax Sticks:
(for retouching wrench damaged
wax coating)
Specify: (Specify color) color coded
Wax Stick for retouching (specify tem-
perature rating) temperature rated Se-
ries TY-L Sprinklers, P/N (specify).
Redfor165°F............. P/N56-065-1-155
Blue for 212°F and
280°F . . . . . . . . . . . . . . . . . P/N 56-065-1-286
NOTES
Each wax stick is suitable for retouch-
ing up to twenty-five sprinklers.
The wax used for 280°F sprinklers is
the same as for 212°F sprinklers, and,
therefore, the 280°F sprinkler is limited
to the same maximum ceiling tempera-
ture as the 212°F sprinkler (i.e.,
150°F).
TFP110 Page 7 of 8
P/N 53 — XXX — X — XXX
165°F/74°C165
TEMPERATURE
RATING
8.0K UPRIGHT (1/2"NPT)
107
106
1
SPRINKLER
TABLE B
PART NUMBER SELECTION
SERIES TY-L PENDENT AND UPRIGHT SPRINKLERS
8.0K PENDENT (1/2"NPT)
212°F/100°C
280°F/138°C280
212NATURAL BRASS
9
MODEL/SIN
CHROME PLATED
7LEAD COATED
6WAX COATED
165°F to 280°F
ONLY
8WAX OVER LEAD
165°F and 212°F
ONLY
101 8.0K UPRIGHT (3/4"NPT)
102 8.0K PENDENT (3/4"NPT)
111 5.6K UPRIGHT (1/2"NPT)
112 5.6K PENDENT (1/2"NPT)
TY3111
TY3211
TY4111
TY4211
TY4811
TY4911

Page8of8 TFP110
TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446