Tyco ESFR-17 User manual

Page 1 of 4 DECEMBER 2022 TFP317
Worldwide
Contacts
www.tyco-fire.com
IMPORTANT
Refer to Technical Data Sheet
TFP2300 for warnings pertaining to
regulatory and health information.
Always refer to Technical Data
Sheet TFP700 for the “INSTALLER
WARNING” that provides cautions
with respect to handling and instal-
lation of sprinkler systems and com-
ponents. Improper handling and
installation can permanently damage
a sprinkler system or its compo-
nents and cause the sprinkler to fail
to operate in a fire situation or cause
it to operate prematurely.
Scan the QR code or enter the URL
in a web browser to access the most
up-to-date electronic version of this
document. Data rates may apply.
docs.jci.com/tycofire/tfp317
Model ESFR-17
16.8 K-factor Pendent Sprinkler
Early Suppression, Fast Response
In all cases, the appropriate NFPA or
FM Global installation standard, or
other applicable standard, must be ref-
erenced to ensure applicability and to
obtain complete installation guidelines.
The general guidelines in this technical
data sheet are not intended to provide
complete installation criteria.
Sprinkler
Identification
Number (SIN)
See Table A
Technical
Data
Approvals
UL and C-UL Listed
FM Approved
EAC Approved
Finish
Natural Brass
Physical Characteristics
Frame � � � � � � � � � � � � � � � � � � � � � � � � � � � � �Brass
Deflector � � � � � � � � � � � � � � � � � � � � � � � � � �Bronze
Compression Screw � � � � � � � � � � Stainless Steel
Hook � � � � � � � � � � � � � � � � � � � � � � � � � � � � MONEL
Strut� � � � � � � � � � � � � � � � � � � � � � � � � � � � � MONEL
Link Assembly� � � � � � � � � � � � � � � � Solder, Nickel
Button �������������������Phosphor Bronze
Sealing Assembly ��Beryllium Nickel w/TEFLON
Additional Technical Data
See Table A
General
Description
The TYCO Model ESFR-17 Pendent
Sprinklers are Early Suppression, Fast
Response (ESFR) sprinklers with a
nominal K-factor of 16�8� The sprinkler
assembly is shown in Figures 1 and 2�
They are suppression mode sprinklers
that are especially advantageous as a
means of eliminating in-rack sprinklers
when protecting high-piled storage�
Model ESFR-17 Pendent Sprinklers are
primarily used for ceiling-only sprinkler
protection of, but not limited to, the fol-
lowing storage applications:
• Most encapsulated or non-encap-
sulated common materials including
cartoned, unexpanded plastics
• Cartoned, expanded plastics
• Uncartoned, unexpanded plastics
• Uncartoned, expanded plastics
•
Some storage arrangements of
rubber tires, roll paper, and aerosols
For more specific criteria, see Table B
and the applicable design standard�
The Model ESFR-17 Pendent Sprin-
klers provide the system designer
with hydraulic and sprinkler place-
ment options not presently available
to traditional ESFR Sprinklers having
a nominal K-factor of 14�0� In particu-
lar, Model ESFR-17 Pendent Sprinklers
are designed to operate at substan-
tially lower-end head pressures, as
compared to ESFR Sprinklers having
a nominal K-factor of 14�0� This feature
offers flexibility when sizing system
piping, as well as possibly reducing or
eliminating the need for a system fire
pump�
WARNING
Orange protector must not be removed
until sprinkler is to be placed in service.
The W-Type 35 sprinkler wrench must
be used for proper installation of the
sprinkler. Failure to do so may result in
equipment damage or failure.
NOTICE
The Model ESFR-17 Pendent Sprinklers
described herein must be installed and
maintained in compliance with this
document, as well as with the appli-
cable standards of the National Fire
Protection Association (NFPA), in addi-
tion to the standards of any authorities
having jurisdiction, such as FM Global.
Failure to do so may impair the perfor-
mance of these devices.
The owner is responsible for main-
taining their fire protection system
and devices in proper operating con-
dition. Contact the installing contrac-
tor or product manufacturer with any
questions.

TFP317
Page 2 of 4
Operation
The fusible link assembly is com-
prised of two link halves that are joined
together by a thin layer of solder� When
the rated temperature is reached, the
solder melts and the two link halves
separate, activating the sprinkler and
flowing water�
TABLE A
MODEL ESFR-17 PENDENT SPRINKLER
TECHNICAL DATA
Item Description
Sprinkler Identication Number (SIN) TY7223
K Factor, (gpm/psi½) (Lpm/bar½)16.8 gpm/psi½(241,9 Lpm/bar½)
Temperature Rating ºF (ºC) 165ºF (74ºC)
212ºF (100ºC)
Thread Size 3/4 in. NPT or ISO 7-R 3/4
Sprinkler Orientation Pendent
Maximum Working Pressure, psi (bar) 175 psi (12,1 bar)
*
*
**
**
*
1-1/2"
(38,1 mm)
THERMAL
SENSING
ELEMENT
3/4"
NPT
2-3/8"
(60,3 mm)
WRENCH
FLATS
1/2"
(12,7 mm)
NOMINAL
MAKE-IN
-Link Assembly
6
-Compression Screw
3
Hook
Strut
-
4
-
5
Deector
Components:
Frame
-
1
2
-
7
-
8
-Sealing Assembly
Button
Temperature rating is indicated
on Deector.
ISO 7-R 3/4 pipe thread can be
provided on special request.
2
3
6
7
8
1
4
5
*
*
**
**
*
1-1/2"
(38,1 mm)
THERMAL
SENSING
ELEMENT
3/4"
NPT
2-3/8"
(60,3 mm)
WRENCH
FLATS
1/2"
(12,7 mm)
NOMINAL
MAKE-IN
-Link Assembly
6
-Compression Screw
3
Hook
Strut
-
4
-
5
Deector
Components:
Frame
-
1
2
-
7
-
8
-Sealing Assembly
Button
Temperature rating is indicated
on Deector.
ISO 7-R 3/4 pipe thread can be
provided on special request.
2
3
6
7
8
1
4
5
WRENCH
RECESS
"FITTING SIDE"
TOWARD
SPRINKLER
FITTING
LINK
PROTECTOR
FIGURE 1
MODEL ESFR-17 PENDENT SPRINKLER, 16.8K, 165°F (74°C)
EARLY SUPPRESSION, FAST RESPONSE
FIGURE 2
MODEL ESFR-17 PENDENT SPRINKLER, 16.8K, 212°F (100°C)
EARLY SUPPRESSION, FAST RESPONSE
FIGURE 3
W-T YPE 35
SPRINKLER WRENCH

TFP317
Page 3 of 4
Design
Criteria
The following general guidelines pro-
vided for the TYCO Model ESFR-17
Pendent Sprinklers can be used for a
quick reference�
The National Fire Protection Associa-
tion (NFPA) and FM Global (FM Approv-
als) provide installation standards that
must be used to properly design an
automatic sprinkler system utilizing
Early Suppression, Fast Response
(ESFR) Sprinklers� The guidelines pro-
vided by NFPA and FM Global may
differ� Consequently, the appropri-
ate standard must be used for a given
installation� For more information, see
Table B�
In all cases, the appropriate NFPA or
FM Global installation standard must
be referenced to ensure applicabil-
ity and to obtain complete installa-
tion guidelines� The following general
guidelines are not intended to provide
complete installation criteria�
Roof Construction
Unobstructed or obstructed construc-
tion, such as smooth ceiling, bar joists,
beam and girder�
Note: In buildings with obstructed con-
struction, where the depths of the solid
structural members, as in beams and
stem, exceed 12 in. (302 mm), install
ESFR Sprinklers in each channel
formed by the structural members.
Ceiling Slope
Maximum 2 in� rise for 12 in� run (16�7%)
Maximum Coverage Area
100 ft² (9,3 m²)
Minimum Coverage Area
64 ft² (5,8 m²) per NFPA 13
Maximum Spacing
• 12 ft (3,7 m) for building heights up
to 30 ft (9,1 m)
• 10 ft (3,1 m) for building heights
greater than 30 ft (9,1 m)
Minimum Spacing
8 ft (2,4 m)
Minimum Clearance to Commodity
36 in� (914 mm)
NFPA 13
Deflector-to-Ceiling Distance
6 in� to 14 in� (152 mm to 356 mm)
FM Global 2-0
Consult FM Global and/or FM Global
guidelines for allowable deflector-to-
ceiling distances as well as thermal
sensing element-to-ceiling criteria�
Storage Type NFPA FM Global
Sprinkler Type ESFR Storage
Response Type FR QR
System Type Wet Wet
Temperature Rating ºF (ºC) 165ºF (74ºC)
212ºF (100ºC) 165ºF (74ºC) 212ºF (100ºC)
Open Frame (i.e., no solid shelves) Single, Double, Multiple-
Row, or Portable Rack Storage of Class I-IV and Group A or
B Plastics Refer to NFPA 13 Refer to FM 2-0 and 8-9
Solid Pile or Palletized Storage of Class I-IV and Group A or
B Plastics Refer to NFPA 13 Refer to FM 2-0 and 8-9
Idle Pallet Storage Refer to NFPA 13 Refer to FM 2-0, 8-9, and 8-24
Rubber Tire Storage Refer to NFPA 13 Refer to FM 2-0 and 8-3
Roll Paper Storage
(Refer to the Standard) Refer to NFPA 13 Refer to FM 8-21
Flammable/Ignitable Liquid Storage
(Refer to the Standard) Refer to NFPA 30 Refer to FM 7-29
Aerosol Storage
(Refer to the Standard) Refer to NFPA 30B Refer to FM 7-31
Automotive Components in Portable Racks
(Control mode only; refer to the Standard) N/A N/A
N/A – Not Applicable
TABLE B
MODEL ESFR-17 PENDENT SPRINKLER
COMMODITY SELECTION AND DESIGN CRITERIA OVERVIEW

TFP317
Page 4 of 4
NATIONAL FIRE PROTECTION ASSOCIATION and NFPA are registered trademarks of National Fire Protection Association;
MONEL and INCONEL are registered trademarks of Special Metals Corporation;
TEFLON is a trademark of The Chemours Company FC, LLC
1467 Elmwood Avenue, Cranston, RI 02910 | Telephone [phone]
© 2022 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.
Installation
TYCO Model ESFR-17 Early Suppres-
sion, Fast Response 16�8K Pendent
Sprinklers must be installed in accor-
dance with this section�
General Instructions
Avoid damage to the fusible Link
Assembly during installation by using
only the Frame arms to handle the
sprinkler and by using the appropri-
ate sprinkler wrench� Do not apply
pressure to the fusible Link Assembly�
Failure to do so can lead to an unstable
link assembly and premature activation
of the sprinkler� Damaged sprinklers
must be replaced�
A leak-tight 3/4 in� NPT sprinkler joint
should be obtained by applying a min-
imum-to-maximum torque of 10 to 20
lb-ft (13,4 to 26,8 N∙m), or by hand-
tightening and applying an additional
1-1/4 to 1-1/2 revolutions of the wrench�
Higher levels of torque can distort the
sprinkler inlet with consequent leakage
or impairment of the sprinkler�
WARNING
Orange protector must not be removed
until sprinkler is to be placed in service.
The W-Type 35 sprinkler wrench must
be used for proper installation of the
sprinkler. Failure to do so may result in
equipment damage or failure.
Note: Install the Model ESFR-17
Pendent Sprinkler only in the pendent
position as shown in Figure 3.
Step 1. With pipe-thread sealant
applied, hand-tighten the sprinkler into
the sprinkler fitting� Do not apply pres-
sure to the Link Assembly, and handle
the Model ESFR-17 Sprinkler only by
the Frame arms�
Step 2. Wrench-tighten the Model
ESFR-17 Sprinkler using only the
W-Type 35 Sprinkler Wrench as shown
in Figure 3, and by fully engaging
(seating) the wrench on the sprinkler
wrench flats as shown in Figures 1 and
2�
Step 3. After installation, inspect the
Link Assembly of each Model ESFR-17
Sprinkler for damage� In particular,
verify that the Link Assembly and Hook
are positioned as shown in Figures 1
and 2, and that the Link Assembly is
not bent, creased, or forced out of
normal position in any way� Replace
damaged sprinklers�
Care and
Maintenance
TYCO Model ESFR-17 Early Suppres-
sion, Fast Response 16�8K Pendent
Sprinklers must be maintained and ser-
viced in accordance with this section�
Before closing a fire protection system
main control valve for maintenance
work on the fire protection system
that it controls, obtain permission to
shut down the affected fire protection
system from the proper authorities
and notify all personnel who may be
affected by this action�
Sprinklers which are found to be
leaking or exhibiting visible signs of
corrosion must be replaced�
Automatic sprinklers must never be
painted, plated, coated, or other-
wise altered after leaving the factory�
Modified sprinklers must be replaced�
Sprinklers that have been exposed to
corrosive products of combustion, but
have not operated, should be replaced
if they cannot be completely cleaned
by wiping the sprinkler with a cloth or
by brushing it with a soft bristle brush�
Care must be exercised to avoid
damage to the sprinklers before,
during, and after installation� Sprin-
klers damaged by dropping, striking,
wrench twist/slippage, or the like, must
be replaced� For more information, see
the Installation section�
The owner is responsible for the
inspection, testing, and maintenance of
their fire protection system and devices
in compliance with this document, as
well as with the applicable standards
of the National Fire Protection Associ-
ation, such as NFPA 25, in addition to
the standards of any authorities having
jurisdiction� Contact the installing con-
tractor or product manufacturer with
any questions�
Automatic sprinkler systems are rec-
ommended to be inspected, tested,
and maintained by a qualified Inspec-
tion Service in accordance with local
requirements and/or national codes�
Limited
Warranty
For warranty terms and conditions, visit
www�tyco-fire�com�
Ordering
Procedure
Contact your local distributor for avail-
ability� When placing an order, indicate
the full product name and part number
(P/N)�
Sprinkler Assemblies with
3/4 NPT Thread Connection
Specify: Model ESFR-17 Early Sup-
pression, Fast Response 16�8K
Pendent Sprinklers (TY7223) with 3/4
NPT thread connection, (specify tem-
perature rating), with Natural Brass
finish, P/N (specify):
16 5° F (74° C ) ������������������58-457-1-165
212°F (100°C) �����������������58-457-1-214
Special Order
Sprinkler Assemblies with
ISO 7-R 3/4 Thread Connection
Specify: Model ESFR-17 Early Suppres-
sion, Fast Response 16�8K Pendent
Sprinklers (TY7223) with ISO 7-R 3/4
thread connection, (specify tempera-
ture rating), with Natural Brass finish,
P/N (specify):
16 5° F (74° C ) ������������������58-458-1-165
212°F (100°C) �����������������58-458-1-214
Sprinkler Wrench
Specify: W-Type 35 Sprinkler Wrench
P/N 56-463-1-001

TFP317
Change History Appendix
Worldwide
Contacts
www.tyco-fire.com
1467 Elmwood Avenue, Cranston, RI 02910 | Telephone [phone]
© 2022 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.
ISSUE DATE NOTES
12-22
Page 1, updated QR code and URL; Page 3, Design Criteria Roof Construction sub-section, added
note requiring sprinkler installed in each channel formed by structural members in areas of buildings
with obstructed construction consisting of solid structural members exceeding 12 in. (302 mm) deep;
Page 4, changed corporate address and telephone number to 1467 Elmwood Avenue, Cranston, RI
02910 | Telephone [phone], formerly 1400 Pennbrook Parkway, Lansdale, PA 19446 | Tele-
phone [phone].
04-22 Page 1, Approvals sub-section, added EAC Approved.
11-21 Added QR code and URL to allow convenient access to electronic version from printed document.
03-21
Removed statement from General Description section indicating applications expanding beyond rec-
ognized installation standards and advising customers to contact Technical Services for re test infor-
mation potentially acceptable to authority having jurisdiction.
12-20
Removed greater coverage area statements from Maximum Coverage Area and Maximum Spacing
sections in Design Criteria; Removed references to other Tyco ESFR technical data sheets; Updated
CE Certicate numbers.
03-20 Table B Commodity Selection and Design Criteria, changed NFPA Response Type to Fast Response
(FR), formerly Quick Response (QR).
08-18
Updated Tyco® branding and document format; Added Johnson Controls copyright; Added disclaimer
stating specications and information subject to change without notice; Added reference to Regulatory
and Health Warning Technical Data Sheet TFP2300.
05-18 Organized technical information into tables as required by UL.
12-16
Emphasized requirements for ensuring factory-installed link protector remains attached when handling
and installing until sprinkler is placed in service; Emphasized requirements for use of W-Type 35 sprin-
kler wrench for proper installation.
— TY7223 V1 sprinkler discontinued; TY7223 V2 remains in production, see TFP317 11-2016.
11-16 V2 sprinkler: Changed W-Type 35 sprinkler wrench part number to 56-463-1-001, formerly 56-463-1-001D.
04-16 Changed W-Type 35 sprinkler wrench part number to 56-463-1-001D, formerly 56-463-1-001.
03-16 Claried wrench-tightening requirements in installation procedure.
01-16 Established TY7223 V2 sprinkler; Added FM Global data sheet references for various storage types;
Added W-Type 35 sprinkler wrench, replacing W-Type 34.
10-15 Rev A V1 sprinkler: Claried wrench-tightening requirements for in installation procedure.
10 -15 Established TY7223 V1 sprinkler; Added FM Global data sheet references for various storage types;
Added W-Type 34 sprinkler wrench, replacing W-Type 2.
07-15 Removed W-Type 30 sprinkler wrench.
04-15 Changed Temperature Rating to 212°F (100°C), formerly shown as 214°F (101°C).
09-14 Added differentiation between assemblies featuring 165°F (74°C) from 214°F (101°C) temperature ratings;
Added W-Type 30 Sprinkler Wrench.
08-14 Added FM Approval.
12-13 New Technical Data Sheet TFP317 describes Model ESFR-17 TY7223 Early Suppression Fast Response
16.8 K-factor sprinkler.