Tyco EC-11 Series User manual

Series EC-11 and EC-14 Sprinklers,
11.2 K and 14.0 K Upright and Pendent
Extended Coverage Light and Ordinary Hazard
Page 1 of 8 NOVEMBER 2014 TFP220
IMPORTANT
Always refer to Technical Data
Sheet TFP700 for the “INSTALLER
WARNING” that provides cautions
with respect to handling and instal-
lation of sprinkler systems and
components. Improper handling and
installation can permanently damage
a sprinkler system or its compo-
nents and cause the sprinkler to fail
to operate in a fire situation or cause
it to operate prematurely.
General
Description
TYCO Series EC-11 and EC-14
Extended Coverage Upright and
Pendent Sprinklers are decorative
glass-bulb sprinklers designed for
use in light or ordinary hazard occu-
pancies. They are intended for use in
automatic sprinkler systems designed
in accordance with standard installa-
tion rules (e.g., NFPA 13) for a maximum
coverage area of 400 ft2(37, 2 m 2), as
compared to the maximum coverage
area of 130 ft2(12,1 m2) for standard
coverage sprinklers used in ordinary
hazard occupancies or 225 ft
2
(20,6 m
2
)
for standard coverage sprinklers used
in light hazard occupancies.
Series EC-11 and EC-14 Sprinklers
feature a UL and C-UL Listing that
permits their use with unobstructed
or non-combustible obstructed ceiling
construction as dened and permitted
by NFPA 13, as well as a specic appli-
cation listing for use under concrete
tees.
Series EC-11 and EC-14 Extended
Coverage Sprinklers have been re
tested to compare their performance to
that of standard coverage spray sprin-
klers. These tests have shown that the
protection provided is equal to or more
effective than standard coverage spray
sprinklers.
Corrosion-resistant coatings, where
applicable, help extend the life of
copper alloy sprinklers beyond that
which occurs when exposed to
corrosive atmospheres. Although corro-
sion-resistant coated sprinklers passed
standard corrosion tests of the appli-
cable approval agencies, this testing
is not representative of all possible
corrosive atmospheres. Consequently,
it is recommended that the end user be
consulted with respect to the suitability
of these corrosion-resistant coatings
for any given corrosive environment.
The effects of ambient temperature,
concentration of chemicals, and gas/
chemical velocity should be consid-
ered, along with the corrosive nature of
the chemical to which the sprinklers will
be exposed.
NOTICE
Series EC-11 and EC-14 Extended
Coverage Sprinklers described herein
must be installed and maintained in
compliance with this document, as well
as with the applicable standards of the
National Fire Protection Association, in
addition to the standards of any other
authorities having jurisdiction. Failure to
do so may impair the performance of
these devices.
The owner is responsible for main-
taining their fire protection system and
devices in proper operating condition.
Contact the installing contractor
or product manufacturer with any
questions.
Sprinkler
Identification
Numbers (SINs)
TY5137 - Upright, 11.2K
TY5237 - Pendent, 11.2K
TY6137 - Upright, 14.0K
TY6237 - Pendent, 14.0K
TY5137 is a re-designation for C5137,
G1894, and S2510.
TY5237 is a re-designation for C5237,
G1893, and S2511.
TY6137 is a re-designation for C6137,
G1896, and S2610.
TY6237 is a re-designation for C6237,
G1895, and S2611.

TFP220
Page 2 of 8
Technical
Data
Approvals
TYCO Series EC-11 and EC-14
Extended Coverage Upright, Pendent,
and Recessed Pendent Sprinklers are
UL and C-UL Listed. Refer to Table A
for complete sprinkler approval infor-
mation including corrosion-resistant
status. The approvals apply to the
service conditions indicated in the
Design Criteria section.
Series EC-11 and EC-14 Extended
Coverage Upright and Pendent
Sprinklers are FM Approved. Refer to
Table A for complete sprinkler approval
information including corrosion-resis-
tant status. The approvals apply to
the service conditions indicated in the
Design Criteria section.
The Style 60 Two-Piece Flush
Escutcheon (Figure 4) is UL Listed and
FM Approved for use with the Series
EC-11 and EC-14 Pendent Sprinklers.
Maximum Working Pressure
175 psi (12,1 bar)
Pipe Thread Connection
3/4 inch NPT
Discharge Coefficients
K = 11.2 gpm/psi1/2 (161,3 lpm/bar1/2)
K = 14.0 gpm/psi1/2 (201,6 lpm/bar1/2)
Temperature Ratings
Refer to Table A.
Finish
Sprinkler:
Refer to Table A.
Recessed or Flush Escutcheon:
White-Coated, Chrome-Plated, and
Brass-Plated
Physical Characteristics
Frame ....................... Bronze
Button....................... Bronze
Sealing Assembly.......Beryllium Nickel
w/TEFLON
Bulb ................... Glass (3 mm)
Compression Screw. . . . . . . . . . . . Bronze
Deector...................... Brass
Operation
The glass bulb contains a uid that
expands when exposed to heat. When
the rated temperature is reached, the
uid expands sufciently to shatter
the glass bulb, which then allows the
sprinkler to activate and ow water.
Design
Criteria
TYCO Series EC-11 and EC-14
Extended Coverage Sprinklers must
only be installed in accordance with
the applicable UL and C-UL Listing
or FM Approval requirements as
indicated below. Only Style 30 or 40
Recessed Escutcheons are to be used
for recessed installation, as applicable.
Refer to Tables A, B, and C.
SECTION
CROSS
PENDENTUPRIGHT
1
2
3
4
5
6
WRENCH
FLAT
ESCUTCHEON PLATE
SEATING SURFACE
1/2" (12,7 mm)
NOMINAL MAKE-IN
1-11/16"
(42,7 mm)
2-7/16"
(61,9 mm)
UPRIGHT &
PENDENT
*
**
3/4"
NPT
Pipe thread connections per
ISO 7-1 can be provided on
special request.
5
4
6
Components:
2
3
Temperature rating is
indicated on Deector.
-
Compression Screw
-
Bulb
-Deector
-
-Sealing Assembly
Button
Frame1 -
**
*
*
FIGURE 1
SERIES EC-11 AND EC-14 EXTENDED COVERAGE SPRINKLERS
11.2 K-FACTOR UPRIGHT (TY5137) AND PENDENT (TY5237)
14.0 K-FACTOR UPRIGHT (TY6137) AND PENDENT (TY6237)
ASSEMBLY

TFP220
Page 3 of 8
Hazard Type Temperature Bulb
Liquid
Sprinkler Finish (See Note 5)
Natural
Brass Chrome Plated Polyester* Lead Coated
Light
Table B describes
UL and C-UL
Sensitivity Rating
Table C describes
FM
Sensitivity Rating
Upright
K=11.2 (TY5137)
Pendent
K=11. 2 ( T Y5 237 )
K=14.0 (TY6237)
135°F (57°C) Orange 1, 2, 3**, 4
155°F (68°C) Red
175°F ( 79°C) Yellow
1, 2, 4 1, 2, 4200°F (93°C) Green
286°F (141°C) Blue
Recessed Pendent
K=11. 2 ( T Y5 237 )
K=14.0 (TY6237)
With Style 30
Escutcheon
135°F (57°C) Orange 1, 2, 3, 4
N/A
155°F (68°C) Red
175°F ( 79°C) Yellow
1, 2, 4200°F (93°C) Green
286°F (141°C) Blue
Ordinary
Table B describes
UL and C-UL
Sensitivity Rating
Table C describes
FM
Sensitivity Rating
Upright
K=11.2 (TY5137)
K=14.0 (TY6137)
Pendent
K=11. 2 ( T Y5 237 )
K=14.0 (TY6237)
135°F (57°C) Orange
1, 2, 3, 4
1, 2, 3, 4
155°F (68°C) Red
175°F ( 79°C) Yellow
1, 2, 4
200°F (93°C) Green
286°F (141°C) Blue
Recessed Pendent
K=11. 2 ( T Y5 237 )
K=14.0 (TY6237)
With Style 30 or 40
Escutcheon
135°F (57°C) Orange
1, 2, 4 N/A
155°F (68°C) Red
175°F ( 79°C) Yellow
200°F (93°C) Green
Notes
(1). Listed by Underwriters Laboratories, Inc. (UL)
(2). Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL)
(3). Approved by Factory Mutual Research Corporation (FM)
(4). Approved by the City of New York under MEA 177-03-E
(5). Where Polyester Coated or Lead Coated Sprinklers are noted to be
UL and C-UL Listed, the sprinklers are UL and C-UL Listed as Cor-
rosion Resistant Sprinklers
* Frame and Deector only.
** Pendent Only
N/A: Not Available
Area Style
Light Hazard Ordinary Hazard
135°F
(57°C)
155°F
(68°C)
175°F
(79°C)
200°F
(93°C)
286°F
(141°C)
135°F
(57°C)
155°F
(68°C)
175°F
(79°C)
200°F
(93°C)
286°F
(141°C)
14 x 14
Upright or Pendent -----QR QR QR QR QR
Style 30 Recessed -----QR QR QR QR QR
Style 40 Recessed -----QR QR QR QR QR
16 x 16
Upright or Pendent QR* QR* QR* QR* QR* SR SR SR SR SR
Style 30 Recessed QR* QR* QR* QR* QR* SR SR SR SR SR
Style 40 Recessed N/A N/A N/A N/A N/A SR SR SR SR SR
18 x 18
Upright or Pendent QR* QR* QR* QR* QR* SR SR SR SR SR
Style 30 Recessed QR* QR* QR* QR* QR* SR SR SR SR SR
Style 40 Recessed N/A N/A N/A N/A N/A SR SR SR SR SR
20 x 20
Upright or Pendent QR* QR* QR* SR* SR* SR SR SR SR SR
Style 30 Recessed QR* QR* QR* SR* SR* SR SR SR SR SR
Style 40 Recessed N/A N/A N/A N/A N/A SR SR SR SR SR
QR: Quick Response
SR: Standard Response
N/A: Not Applicable
* Does not apply to Upright K=14.0
TABLE A
LABORATORY LISTINGS AND APPROVALS
TABLE B
SENSITIVITY RATING FOR UL AND C-UL LISTING OF SERIES EC-11 OR EC-14 SPRINKLERS
(Refer to Table D for Permitted K-Factor/Area Combinations)

TFP220
Page 4 of 8
UL and C-UL
Listing Requirements
1. Series EC-11 and EC-14 Sprinklers
may be used for the coverage areas
shown in Table D, based on main-
taining the minimum specied ow
rate as a function of coverage area
and hazard group for all sprinklers
in the design area.
2. Series EC-11 and EC-14 Sprinklers
are permitted to be used with
unobstructed or non-combustible
obstructed ceiling construction as
dened and permitted by NFPA 13;
for example:
• Unobstructed, combustible or
noncombustible, ceiling construc-
tion with a deector to ceiling/roof
deck distance of 1 to 12 inches
(25 to 300 mm).
• Obstructed, non-combustible,
ceiling construction with a
deector location below struc-
tural members of 1 to 6 inches
(25 to 150 mm) and a maximum
deector to ceiling/roof deck
distance of 22 inches (550 mm).
3. Series EC-11 and EC-14 Sprinklers,
specically tested and listed for
non-combustible obstructed
construction, are permitted to be
used within trusses or bar joists
having non-combustible web
members greater than 1 inch (25.4
mm) when applying the 4 times
obstruction criteria rule dened
under “Obstructions to Sprinkler
Discharge Pattern Development”.
4. To prevent cold soldering, the
minimum allowable spacing
between Series EC-11 and EC-14
Sprinklers, is 8 feet (2,4 m) for
upright sprinklers and 9 feet (2,7 m)
for pendent sprinklers.
HC-1
Linear Spacing Area Spacing Ceiling
Height Ceiling Type K-factor Style Response
Min Max Min Max
10 20 100 400 Up to 30
Noncombustible Unobstructed,
Noncombustible Obstructed, or
Combustible Unobstructed
11.2 EC
14.0 EC
Pendent or
Upright
Quick
10 20 100 400 Up to 30
Noncombustible Unobstructed,
Noncombustible Obstructed, or
Combustible Unobstructed
11.2 EC
14.0 EC
Pendent
Recessed
Style 30
10 20 100 400 Up to 30 Combustible obstructed 11.2 EC
14.0 EC
Pendent or
Upright
10 20 100 400 Up to 30 Combustible obstructed 11.2 EC
14.0 EC
Pendent
Recessed
Style 30
10 20 100 400 Over 30 and
up to 45 Noncombustible Unobstructed 11.2 EC 14.0 EC Upright
HC-2
Linear Spacing Area Spacing Ceiling
Height Ceiling Type K-factor Style Response
Min Max Min Max
10 20 100 400 Up to 30
Noncombustible Unobstructed,
Combustible Unobstructed
11.2 EC Upright
Quick
10 20 100 400 Up to 30 14.0 EC Pendent or
Upright
10 16 100 256 Over 30 and
up to 45
11.2 EC
14.0 EC Upright
HC-3
Linear Spacing Area Spacing Ceiling
Height Ceiling Type K-Factor Style Response
Min Max Min Max
10 16 100 256 Up to 30
Noncombustible Unobstructed,
Combustible Unobstructed
11.2 EC Upright
Quick
10 20 100 400 Up to 30 14.0 EC Pendent or
Upright
10 16 100 256 Over 30 and
up to 45
11.2 EC,
14.0 EC Upright
NOTE
1. The design for K 11.2 EC (K 160 EC) sprinklers should not include fewer than six sprinklers or have a design pressure of less than 12 psi (0,8 bar);
similarly the design for K 14.0 EC (K 200 EC)sprinklers should not include fewer than four sprinklers or have a design pressure of less than
18 psi (1,2 bar).
2. For ow criteria, refer to FM Loss Prevention Data Sheet 3-26.
TABLE C
SENSITIVITY RATING FOR FM APPROVAL OF SERIES EC-11 OR EC-14 SPRINKLERS
(Note: Refer to FM Loss Prevention Data Sheet 2-0 for permitted K-factor/area combinations)

TFP220
Page 5 of 8
5. Series EC-11 and EC-14 Sprinklers
are to be installed in accordance
with all other requirements of
NFPA 13 for extended coverage
upright and pendent sprinklers; For
example, obstructions to sprinkler
discharge, obstructions to sprinkler
pattern development, obstructions
to prevent sprinkler discharge from
reaching hazard and clearance to
storage.
UL and C-UL
Specific Application Listing
Requirements for Installation
under Concrete Tees
Series EC-11 and EC-14 Extended
Coverage Upright and Pendent
Sprinklers (TY5137, TY5237, TY6137
and TY6237) have a UL and C-UL
Specic Application Listing for use
under concrete tees when installed as
follows:
1. Stems of the concrete tee construc -
tion must spaced at less than 7.5
feet (2,3 m) on center but more than
3 feet (0,9 m) on center. The depth of
the concrete tees must not exceed
30 inches (762 mm). The maximum
permitted concrete tee length is 32
feet (9,8 m). However, where the
concrete tee length exceeds 32 feet
(9,8 m), non-combustible bafes,
equal in height to the depth of the
tees, can be installed so that the
space between the tees does not
exceed 32 feet (9,8 m) in length.
2. The sprinkler deectors are to be
located in a horizontal plane at or
above 1 inch (25,4 mm) below the
bottom of the concrete tee stems.
3. When the sprinkler deectors are
located higher than a horizontal
plane 1 inch (25,4 mm) beneath
the bottom of the concrete tee
stems, the obstruction to sprinkler
discharge criteria requirements of
NFPA 13 for extended coverage
upright and pendent sprinklers
applies.
FM Approval Requirements
Series EC-11 and EC-14 Extended
Coverage Sprinklers are to be installed
in accordance with the applicable
Factory Mutual Loss Prevention Data
Sheet for limited use in buildings of
specic roof construction and for the
protection of certain specic ordinary
hazard (non-storage and/or non-am-
mable or combustible liquid) occu-
pancies. Information provided in the
FM Loss Prevention Data Sheets
relates to, but not limited to, hydraulic
design, ceiling slope, and obstructions,
minimum and maximum allowable
spacing, and deector-to-ceiling
distance.
These criteria may differ from UL and/or
NFPA criteria. Therefore, the designer
should review and become familiar with
Factory Mutual requirements before
proceeding with design.
Description Area
Light Hazard
0.10 gpm/ft2
Group I
Ordinary Hazard
0.15 gpm/ft2
Group II
Ordinary Hazard
0.20 gpm/ft2
gpm psi gpm psi gpm psi
TY5137
(K=11.2) Upright
14 x 14 30 7. 2 30 7. 2 39 12.1
16 x 16 30 7. 2 39 12.1 51 20.7
18 x 18 33 8.7 49 19.1 65 33.7
20 x 20 40 12.8 60 28.7 80 51.0
TY5237
(K=11.2) Pendent
14 x 14 30 7. 2 30 7. 2 39 12.1
16 x 16 30 7. 2 39 12.1 51 20.7
18 x 18 33 8.7 49 19.1 65 33.7
20 x 20 40 12.8 60 28.7 80 51.0
TY6137
(K=14.0) Upright
14 x 14 N/A N/A 39 7.8 51 13.3
16 x 16 N/A N/A 39 7.8 51 13.3
18 x 18 N/A N/A 49 12.3 65 21.6
20 x 20 N/A N/A 60 18.4 80 32.7
TY6237
(K=14.0) Pendent
14 x 14 37 7.0 39 7.8 51 13.3
16 x 16 37 7.0 39 7. 8 51 13.3
18 x 18 37 7.0 49 12.3 65 21.6
20 x 20 40 8.2 60 18.4 80 32.7
1 ft. = 0.3048 m
1 ft.2=0.093 m2
1 gpm = 3.785 lpm
1 psi = 0.06895 bar
1 gpm/ft2= 40.74 mm/min
TABLE D
FLOW CRITERIA FOR UL AND C-UL LISTING OF SERIES EC-11 AND EC-14 SPRINKLERS

TFP220
Page 6 of 8
Installation
Series EC-11 and EC-14 Sprinklers
must be installed in accordance with
this section.
General Instructions
Do not install any bulb-type sprinkler if
the bulb is cracked or there is a loss of
liquid from the bulb. With the sprinkler
held horizontally, a small air bubble
should be present. The diameter of the
air bubble is approximately 1/16 inch
(1,6 mm) for the 135°F (57°C) to 3/32
inch (2,4 mm) for the 286°F (141°C)
temperature ratings.
A leak-tight 3/4 inch NPT sprinkler
joint should be obtained by applying
a minimum-to-maximum torque of
10 to 20 ft.-lbs. (13,4 to 26,8 Nm).
Higher levels of torque may distort the
sprinkler inlet with consequent leakage
or impairment of the sprinkler.
Do not attempt to compensate
for insufcient adjustment in an
Escutcheon Plate by under or over-
tightening the Sprinkler. Re-adjust the
position of the sprinkler tting to suit.
Step 1. Install the sprinkler with the
deector parallel to the mounting
surface. Install pendent sprinklers in the
pendent position; install upright sprin -
klers in the upright position.
Step 2. After installing the Style 30,
40, or 60 mounting plate (or other
applicable escutcheon) over the
sprinkler pipe threads and with pipe-
thread sealant applied to the pipe
threads, hand-tighten the sprinkler into
the sprinkler tting.
Step 3. For upright or pendent sprin-
klers wrench-tighten using only the
MOUNTING
SURFACE
FACE OF
SPRINKLER
FITTING
2-1/4" DIA.
(57,2 mm)
2-7/8" DIA.
(73,0 mm)
MOUNTING
PLATE
1/8"
(3,2 mm)
5/8±1/4"
(15,9±6,4 mm)
7/8" (22,2 mm)
1-3/8" (34,9 mm)
1/4" (6,4 mm)
3/4" (19,1 mm)
CLOSURE
MOUNTING
SURFACE
1/8"
(3,2 mm)
1-13/16" (46,0 mm)
2-5/16" (58,7 mm)
CLOSURE
ESCUTCHEON PLATE
SEATING SURFACE:
1/4" (6,4 mm) ABOVE
TO 1/2" (12,7 mm) BELOW
MOUNTING SURFACE;
3/4" (19,1 mm) TOTAL
ADJUSTMENT
2-1/4" DIA.
(57,2 mm)
2-7/8" DIA.
(73,0 mm)
FACE OF
SPRINKLER FITTING:
3/8" (9,5 mm) ABOVE
TO 1/8" (3,2 mm) BELOW
MOUNTING SURFACE
3/4" NPT
MOUNTING
PLATE
INTERNAL
DIMENSIONS OF
STYLE 60 ESCUTCHEON
ACCOMMODATE
CLASS 150 MALLEABLE
IRON REDUCING
SPRINKLER FITTING
"FITTING SIDE"
TOWARDS SPRINKLER
FITTING
WRENCH
RECESS
(END "A")
WRENCH
RECESS
WRENCH
HEX
1/4" (6,4 mm)
1/2" (12,7 mm)
MOUNTING
SURFACE
FACE OF
SPRINKLER
FITTING
1/2±1/8"
(12,7±3,2 mm) 2-1/4" DIA.
(57,2 mm)
2-7/8" DIA.
(73,0 mm)
CLOSURE
1-3/8" (34,9 mm)
1-1/8" (28,6 mm)
MOUNTING
PLATE
1/8"
(3,2 mm)
FIGURE 3
SERIES EC-11 AND EC-14 RECESSED
PENDENT SPRINKLER ASSEMBLY
WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT
STYLE 40 RECESSED ESCUTCHEON
FIGURE 4
SERIES EC-11 AND EC-14 PENDENT SPRINKLER ASSEMBLY
WITH 3/4 INCH TOTAL ADJUSTMENT
STYLE 60 TWO-PIECE FLUSH ESCUTCHEON
FIGURE 5
W-TYPE 3 SPRINKLER
WRENCH
FIGURE 6
W-TYPE 22 RECESSED
SPRINKLER WRENCH
FIGURE 2
SERIES EC-11 AND EC-14 RECESSED
PENDENT SPRINKLER ASSEMBLY
WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 30 RECESSED ESCUTCHEON

TFP220
Page 7 of 8
P/N 51 – XXX – X – XXX
* Escutcheon ordered separately
** OPEN indicates sprinkler
assembly without glass bulb,
button, and sealing assembly.
W-Type 3 (End A) Sprinkler Wrench.
For the pendent sprinkler installed
with Style 30, 40, or 60 Escutcheon,
wrench-tighten the sprinkler using only
the W-Type 22 Sprinkler Wrench.
Apply the wrench recess of the appli-
cable sprinkler wrench (Figure 5 and 6)
to the sprinkler wrench ats (Figure 1).
Care and
Maintenance
TYCO Series EC-11 and EC-14
Sprinklers must be maintained and
serviced in accordance with this
section.
Before closing a re protection system
main control valve for maintenance
work on the re protection system
that it controls, obtain permission to
shut down the affected re protection
systems from the proper authorities
and notify all personnel who may be
affected by this action.
Sprinklers which are found to be
leaking or exhibiting visible signs of
corrosion must be replaced.
Automatic sprinklers must never be
painted, plated, coated, or otherwise
altered after leaving the factory.
Modied sprinklers must be replaced.
Sprinklers that have been exposed to
corrosive products of combustion, but
have not operated, should be replaced
if they cannot be completely cleaned
by wiping the sprinkler with a cloth or
by brushing it with a soft bristle brush.
Care must be exercised to avoid
damage to the sprinklers before,
during, and after installation. Sprinklers
damaged by dropping, striking, wrench
twist/slippage, or the like, must be
replaced. Also, replace any sprinkler
that has a cracked bulb or that has lost
liquid from its bulb. (Ref. Installation
Section.)
Frequent visual inspections are recom-
mended to be initially performed for
corrosion resistant coated sprin-
klers, after the installation has been
completed, to verify the integrity of the
corrosion resistant coating. Thereafter,
annual inspections per NFPA 25 should
sufce; however, instead of inspecting
from the oor level, a random sampling
of close-up visual inspections should
be made, so as to better determine the
exact sprinkler condition and the long
term integrity of the corrosion resistant
coating, as it may be affected by the
corrosive conditions present.
The owner is responsible for the
inspection, testing, and maintenance of
their re protection system and devices
in compliance with this document, as
well as with the applicable standards
recognized by the Approval agency
(e.g., NFPA 25), in addition to the
standards of any authorities having
jurisdiction. Contact the installing
contractor or product manufacturer
with any questions.
Automatic sprinkler systems are recom-
mended to be inspected, tested, and
maintained by a qualied Inspection
Service in accordance with local
requirements and/or national codes.
Limited
Warranty
For warranty terms and conditions, visit
www.tyco-re.com.
Ordering
Procedure
Contact your local distributor for
availability. When placing an order,
indicate the full product name and Part
Number (P/N).
Sprinkler Assemblies with
NPT Thread Connections
Specify: Series EC-11 or EC-14 (specify)
Sprinkler, SIN (specify), (specify)
K-factor, Pendent or Upright (specify)
Extended Coverage, (specify) temper-
ature rating, (specify) nish, P/N (from
to Table E)
Recessed Escutcheon, Two-Piece
Specify: Style (30 or 40) Two-Piece
Recessed Escutcheon with (specify)
nish, P/N (specify*)
Flush Escutcheon, Two-Piece
Specify: Style 60 Two-Piece Flush
Escutcheon with (specify) nish, P/N
(specify*)
*Refer to Technical Data Sheet TFP778
Sprinkler Wrenches
Specify: W-Type 3 Sprinkler Wrench,
P/N 56-895-1-001
Specify: W-Type 22 Recessed Sprinkler
Wrench, P/N 56-665-7-001
SIN
893 11.2K PENDENT TY5237
894 11.2K UPRIGHT TY5137
895 14.0K PENDENT TY6237
896 14.0K UPRIGHT TY6137
SPRINKLER
FINISH*
1NATURAL BRASS
4SIGNAL WHITE (RAL9003)
POLYESTER
5JET BLACK (RAL9005)
POLYESTER
7LEAD COATED
9CHROME-PLATED
TEMPERATURE
RATING
135 135°F (57°C)
155 155°F (68°C)
175 175°F (79°C)
200 200°F (93°C)
286 286°F (141°C)
000 OPEN**
TABLE E
SERIES EC-11 AND EC-14 UPRIGHT AND PENDENT SPRINKLERS
PART NUMBER SELECTION

TFP220
Page 8 of 8