Tyco Illustra Standard Series User manual

Package
Overview
Installation
1
2
3
4
Warning and Caution
■ If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■ Keep away from liquid while in use.
■ In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the product
is mounted on wall or ceiling, the device shall be firmly fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
If the device will not be used for a long time, please cover the lens
cap to protect the device from dirt.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold (the operating
temperature shall be -30˚C~60˚C), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for
operating environment.
■ A few parts of the device shall be replaced regularly according
to their average enduring time.
Camera Quick start guide
CD Plastic plug ×4
Drill template
Sponge Screwdriver
4 tapping screws
CVBS&DC
IN cables
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
●
Alarm Input: Join the grounding ends of the sensor and the camera
and then connect the signal cable of the sensor to the alarm input
port (ALM-INA) of the camera.
Alarm Output: Loosen the screws in the alarm output port. Then
insert the signal wires of the alarm output devices into the port of
OPEN and COM separately. Finally tighten the screws. Some of the
external alarm output devices need the power supply.
Alarm Connection
■ Please read this instruction carefully before using the product and keep
it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without notice.
2
13
* If the PoE switch is used to power the camera, DC12V/AC24V power supply is
not required.
* AC24V power supply is not available for ISV-V05M023S-N/ISV-V05M024S-N/
JSV05-D02-OI01.
* Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera.
* Please install the camera in the dry environment. You'd better install
back the lower dome less than 4 hours after removing it.
* Do not directly touch the dome when installing.
* Do not remove the protection film until finishing the installation.
lock screw to remove the mounting base.
② Attach the drill template to the place where you want to fix the
camera and then drill 4 screw holes and 1 cable hole (if you want to
route the cables through the mounting base) according to the drill
template.
① Loosen the screws to open the lower dome and then loosen the
● Connecting Network Cable
1
3
4
5
6
2
ALARM
4 3 2 1
10
7
8
9
11
12
1 Ethernet Connector
2 Audio Input (MIC)
3 Audio Output (HP)
4 CVBS Video Output
5 Alarm Input/Output
6 DC12V Power Connector
7 Zoom-
8 Zoom+
9 Micro SD Card Slot
10 Reset
11 DC IN & CVBS Interface
12 Microphone
Security cap
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
DC12V/AC24V
ALARM
4 3 2 1
Illustra Standard Series
Dome Camera
Quick Start Guide
V

Network Connection
5
③Route and connect these cables.
the ceiling or wall with screws.
Then secure the mounting base to
④ Fix the camera to the mounting base with the lock screw.
Sponge
Mounting Base
⑤ Three-axis adjustment. Before adjustment, preview the image of the
camera on a monitor and then adjust the camera according to the
figure below to get an optimum angle.
⑥ Install the lower dome back to the camera with the screws. Please
tighten the screws for water resistance. Then remove the protection
film softly to complete the installation.
Lock Screw
Lower Dome
∅6
∅148
∅22
88 mm
89mm
Transparent Dome Maintenance
Tips
Transparent dome is an optical element. As dirt, dust or fingerprints on the
dome will reduce the clarity of the image, please don’t touch or wipe the
cover surface directly during installation and use. Please refer to the
following cleaning tips to clean it.
*
* If there is water or grease on the dome, please gently wipe off the water
drop or grease with a soft cloth and then use oil-free cotton cloth with the
neutral detergent to wipe it several times from the center to outward.
Finally, change the cloth to dry it.
* If there are fingerprints on the dome, please use oil-free cotton cloth or
paper soaked with the neutral detergent to wipe it several times from
the center to outward and then dry it with a soft cloth.
If there is dust on the dome, please use a dry soft brush to gently brush it .
Hold it and rotate
Rotation 0°~345°
Tilt 0°~77°
Pan 0°~345°
MENU
IPC
Network Cable Network Cable
Switch
Router Computer
● Access the camera through TycoIPTool
① Make sure that the camera and the PC are well connected to the
LAN.
② Find the TycoIPTool from the CD and then install it in the
computer. After that, run the TycoIPTool as shown below.
③ Modify the IP address. The default IP address of this camera is
192.168.1.168. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as that of the
computer. Please modify the IP address of your device according
to the practical situation.
About
Immediate Refresh
Device Na me
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.1.168
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Device Type
Product M odel
IP Address Http Port Data Port Subnet Mo dify Net work Parameter
Mac Addres s
IP Address
Subnet Ma sk
Gateway
Modify
CE :98 :23 :75 :35 :22
192 . 168 . 1 . 168
255 . 255 . 255 . 0
192 . 168 . 1 . 1
Tip: E nter the administrato r passwo rd, and
then modi fy the net work parameters.
Restore I PC Defau lt Configuration
Total Devic e: 3
Local IP Address:192.168.1.4Su bnet Mas k:255.255.255.0 Gateway : 192.168.1.1DNS：210.21.196.6
i
Mac Address
IP Address
Subnet Mask
Gateway
Modify
CE :98 :23 :75 :35 :22
192 .168 . 1 . 168
255 . 255 . 255 . 0
192 .168 . 1 . 1
Tip: Enter the administrator password, and
then modify the network parameters.
i
Modify Network Parameter
For example, the IP address of your computer is 192.168.1.4. So the
IP address of the camera shall be changed to 192.168.1.X and the
gateway shall be changed to 192.168.1.1. After modification, please
enter the password of the administrator and click “Modify” button to
modify the settings.
The default password of the administrator is “ ”.admin
④ Double-click the camera listed in the IP-Tool or manually enter the
IP address in the address bar of the web browser to connect IP-CAM.
Then follow directions to download and install the plugin.
⑤ Enter the username and password in the login interface.
The default username is admin; the default password is admin.
Available Models:
ISV-V05M023S-N
ISV-V02M014S-N
ISV-V05M024S-N
ISV-V02M013S-N
ISA-V02M015S-N
ISA-V04M015S-N
ISV-V02M015S-N
ISV-V04M015S-N