manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Tyco
  6. •
  7. Security Camera
  8. •
  9. Tyco E Series User manual

Tyco E Series User manual

Package
Overview
1
2
3
* 1 It is recommended to install the security cap for outdoor installation.
* 2 If the PoE switch is used to power the camera that supports PoE power
supply, DC12V power supply is not required.
Warning and Caution
■ If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■ Do not allow water or liquid intrusion into the camera.
■ In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
If the device will not be used for a long time, please cover the lens
cap to protect the device from dirt.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold (the operating
temperature shall be -30˚C~60˚C), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for
operating environment.
Camera Quick start guide
CD Plastic plug ×4
Drill template
Rubber plug Screwdriver
4 tapping screws
Security Cap
■ Please read this instruction carefully for correct use of the
product and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
DC12V
Installation
4
► Connecting Network Cable
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
* Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera.
* Please install the camera in the dry environment. You'd better install
back the lower dome less than 4 hours after removing it.
* Do not directly touch the dome when installing.
* Do not remove the protection film until finishing the installation.
① Attach the drill template to the place where you want to fix the
camera and then drill the screw holes and the cable hole on the wall
according to the drill template.
② Loosen the screws to remove the lower dome from the camera.
2
13
74.25
74.25
(mm)
Lower dome
Network connector
Mounting base
Power connector
Micro SD card slot
Reset
1
2
3
4
5
6
ISE - V 0 5F284 - N
ISE - V 0 5F364 - N
ISE - V 0 4F284 - N
ISE - V 0 4F364 - N
ISE-V05F283S-N
ISE-V05F363S-N
ISE-V04F283S-N
ISE-V04F363S-N
3
1
4
2
5
6
Reset
Illustra Standard SeriesE
Quick Start Guide
Dome Camera
Network Connection
5
MENU
IPC
Network Cable Network Cable
Switch
Router Computer
③
④ Secure the mounting base with camera to the wall with screws as
shown below.
Route and connect the cables.
Rotation 0°~355°
Pan 0°~355°
Rubber Plug
Tilt 0°~67°
⑤
the camera on a monitor and then adjust the camera according to
the figure below to get an optimum angle.
Three-axis adjustment. Before adjustment, preview the image of
⑥
screws. Then remove the protection film to finish the installation.
Install the lower dome back to the camera and secure it with the
Lower Dome
Transparent Dome Maintenance
Tips
Transparent dome is an optical element. As dirt, dust or fingerprints on the
dome will reduce the clarity of the image, please don’t touch or wipe the
cover surface directly during installation and use. Please refer to the
following cleaning tips to clean it.
*
* If there is water or grease on the dome, please gently wipe off the water
drop or grease with a soft cloth and then use oil-free cotton cloth with the
neutral detergent to wipe it several times from the center to outward.
Finally, change the cloth to dry it.
* If there are fingerprints on the dome, please use oil-free cotton cloth or
paper soaked with the neutral detergent to wipe it several times from
the center to outward and then dry it with a soft cloth.
If there is dust on the dome, please use a dry soft brush to gently brush it .
● Access the camera through TycoIPTool
① Make sure that the camera and the PC are well connected to the
LAN.
② Find the TycoIPTool from the CD and then install it in the
computer. After that, run the TycoIPTool as shown below.
③ Modify the IP address. The default IP address of this camera is
192.168.1.168. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as that of the
computer. Please modify the IP address of your device according
to the practical situation.
About
Immediate Refresh
Device Name
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.1.168
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Device Type
Product Model
IP Address Http Port Data Port Subnet Modify Network P arameter
Mac Address
IP Address
Subnet Mask
Gateway
Modify
CE :98 :23 :75 :35 :22
192 .168 . 1 . 168
255 . 255 . 255 . 0
192 .168 . 1 . 1
Tip: Enter the administrator password, and
then modify the network p arameters.
Restore IPC Default Con figuration
Total Device: 3
Local IP Address:192.168.1.4Subnet Mask:255.255.255.0 Gateway: 192.168.1.1DNS:210.21.196.6
i
For example, the IP address of your computer is 192.168.1.4. So the
IP address of the camera shall be changed to 192.168.1.X and the
gateway shall be changed to 192.168.1.1. After modification, please
enter the password of the administrator and click “Modify” button to
modify the settings.
The default password of the administrator is “ ”.admin
④ Double-click the camera listed in the IP-Tool or manually enter the
IP address in the address bar of the web browser to connect IP-CAM.
Then follow directions to download and install the plugin.
⑤ Enter the username and password in the login interface.
The default username is admin; the default password is admin.
Mac Address
IP Address
Subnet Mask
Gateway
Modify
CE :98 :23 :75 :35 :22
192 . 168 . 1 . 168
255 . 255 . 255 . 0
192 . 168 . 1 . 1
Tip: Enter the administrator password, and
then modify the network parameters.
i
Modify Network Parameter

This manual suits for next models

8

Other Tyco Security Camera manuals

Tyco Illustra Pro User manual

Tyco

Tyco Illustra Pro User manual

Tyco Illustra Standard E Series User manual

Tyco

Tyco Illustra Standard E Series User manual

Tyco Illustra Pro IPS03CFOCWST User manual

Tyco

Tyco Illustra Pro IPS03CFOCWST User manual

Tyco DSC-D114 User manual

Tyco

Tyco DSC-D114 User manual

Tyco Illustra Flex Gen 3 User manual

Tyco

Tyco Illustra Flex Gen 3 User manual

Tyco Illustra Standard V Series User manual

Tyco

Tyco Illustra Standard V Series User manual

Tyco Illustra Standard V Series User manual

Tyco

Tyco Illustra Standard V Series User manual

Tyco Illustra Pro series User manual

Tyco

Tyco Illustra Pro series User manual

Tyco Illustra Standard Series User manual

Tyco

Tyco Illustra Standard Series User manual

Tyco IFS02-D12-ITA4 User manual

Tyco

Tyco IFS02-D12-ITA4 User manual

Tyco Illustra Standard V Series User manual

Tyco

Tyco Illustra Standard V Series User manual

Tyco Illustra Essentials 1MP User manual

Tyco

Tyco Illustra Essentials 1MP User manual

Tyco American Dynamics Illustra 625 User manual

Tyco

Tyco American Dynamics Illustra 625 User manual

Tyco Illustra Standard E Series User manual

Tyco

Tyco Illustra Standard E Series User manual

Popular Security Camera manuals by other brands

Digital Watchdog STAR-LIGHT Universal HD over Coax... quick start guide

Digital Watchdog

Digital Watchdog STAR-LIGHT Universal HD over Coax... quick start guide

Siqura 910 Series user manual

Siqura

Siqura 910 Series user manual

Velleman CAMIP12 Quick reference guide

Velleman

Velleman CAMIP12 Quick reference guide

Security-Center TV7099 installation guide

Security-Center

Security-Center TV7099 installation guide

AVer PTZ310 user manual

AVer

AVer PTZ310 user manual

Sony SNC-CX600 user guide

Sony

Sony SNC-CX600 user guide

4xem WFDV Specifications

4xem

4xem WFDV Specifications

GeoVision GV-BX130D-0 user manual

GeoVision

GeoVision GV-BX130D-0 user manual

Vivotek IP8161 Quick installation guide

Vivotek

Vivotek IP8161 Quick installation guide

Samsung SND-7084R Specifications

Samsung

Samsung SND-7084R Specifications

EOC iD1080?BIR user manual

EOC

EOC iD1080?BIR user manual

Vivotek IP816A-LPC-18 user manual

Vivotek

Vivotek IP816A-LPC-18 user manual

Pyle SereneLife user manual

Pyle

Pyle SereneLife user manual

Nuvico CB-HDE21N installation manual

Nuvico

Nuvico CB-HDE21N installation manual

Platinum CCTV CD-8260 installation manual

Platinum CCTV

Platinum CCTV CD-8260 installation manual

Wisenet SDC-89445BF user manual

Wisenet

Wisenet SDC-89445BF user manual

Reolink RLC-423 Operational Instruction

Reolink

Reolink RLC-423 Operational Instruction

Instar IN-9008 user manual

Instar

Instar IN-9008 user manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.