Tyco Illustra Standard E Series User manual

Package
Overview
Installation
1
2
3
4
► Connecting Network Cable
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
Warning and Caution
■ If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■ Do not allow water or liquid intrusion into the camera.
■ In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold (the operating
temperature shall be -30˚C~60˚C), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for
operating environment.
Camera Quick start guide
CD Plastic plug ×3 Rubber plug Drill template
Screwdriver
Tapping screw ×3
■ Please read this instruction carefully before operating the
unit and keep it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without
notice.
* 1 It is recommended to install the security cap for outdoor installation.
* 2 If the PoE switch is used to power the camera, DC12V power supply is not
required.
Security Cap
2
13
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera. Please install and use
the camera in the dry environment.
①
the drill template.
Drill the screw holes and the cable hole on the wall according to
∅130.7
∅119.5
∅4.5
120°
120°
103.5 mm
59.7mm
29.9mm
②
ceiling or wall with the screws.
Route connect . And then secure the camera to theand the cables
DC12V
1
2
3
4
1
2
3
Ethernet connector
Power connector
Mounting base
Fixed screw
Micro SD card slot
Reset
4
5
6
56
Illustra Standard SeriesE
Turret Camera
Quick Start Guide
ISL- T04V0 13-N
ISE-T04V013S-N
ISE-T04V014S-N

Network Connection
5
MENU
IPC
Network Cable Network Cable
Switch
Router Computer
④
optimum image. Before adjustment, view the image of the camera on a
monitor.
Open the cover of the camera to adjust Zoom or Focus to obtain an
⑤
(Note that the cover should not be installed unevenly.)
Install the cover back to the camera and fix it with the screws firmly.
Zoom
Focus
Cover
Rubber Plug
Fixed Screw
③
fixed screws. Before adjustment, preview the image of the camera
on a monitor. After that, tighten the fixed screws.
Adjust the camera to obtain an optimum angle by loosening the ● Access the camera through TycoIPTool
① Make sure that the camera and the PC are well connected to the
LAN.
② Find the TycoIPTool from the CD and then install it in the
computer. After that, run the TycoIPTool as shown below.
③ Modify the IP address. The default IP address of this camera is
192.168.1.168. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as that of the
computer. Please modify the IP address of your device according
to the practical situation.
About
Immediate Refresh
Device Name
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.1.168
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Device Type
Product Model
IP Address Http Port Data Port Subnet Modify Netw ork Parameter
Mac Address
IP Address
Subnet Mask
Gateway
Modify
CE :98 :23 :75 :3 5 :22
192 .168 . 1 . 168
255 . 255 . 255 . 0
192 .168 . 1 . 1
Tip: Enter the administrator password, and
then modify the netw ork parameters.
Restore IPC Defaul t Configuration
Total Device: 3
Local IP Address:192.168.1.4Subnet Mask:255.255.255.0 Gateway: 192.168.1.1DNS：210.21.196.6
i
For example, the IP address of your computer is 192.168.1.4. So the
IP address of the camera shall be changed to 192.168.1.X and the
gateway shall be changed to 192.168.1.1. After modification, please
enter the password of the administrator and click “Modify” button to
modify the settings.
The default password of the administrator is “ ”.admin
④ Double-click the camera listed in the IP-Tool or manually enter the
IP address in the address bar of the web browser to connect IP-CAM.
Then follow directions to download and install the plugin.
⑤ Enter the username and password in the login interface.
The default username is admin; the default password is admin.
Mac Address
IP Address
Subnet Mask
Gateway
Modify
CE :98 :23 :75 :35 :22
192 .168 . 1 . 168
255 . 255 . 255 . 0
192 .168 . 1 . 1
Tip: Enter the administrator password, and
then modify the network parameters.
i
Modify Network Parameter