U-Line H-5598 User manual

PAGE 1 OF 3 0316 IH-5598
πH-5598
IGLOO PARTY BAR
1-800-295-5510
uline.com
PARTS
INSTALLATION
Lid x 1
Rigid
Caster x 2
Long Screws
Mounting
Bracket
Cooler
Locking
Caster x 2
Caster Mounting
Hardware x 16
Bottle
Opener x 1
Short
Screw x 2
Long
Screw x 2
Cap Catch
Bin x 1
Mounting
Bracket x 1
Cooler x 1 Base x 1
1. Remove two short screws and bottle opener from
bag. Line up the bottle opener with the two most
upper holes. Using the Phillips screwdriver, tighten
the short screws into the cooler. (See Figure 1)
NOTE: The holes are not pre-cut, but are
marked with indentations in the cooler wall.
2. Attach mounting bracket to cooler wall using the two
long screws. Make sure mounting bracket is upright
(See Figure 1)
NOTE: the holes are not pre-cut, but are
marked with indentations in the cooler wall.
Wrench Phillips
Screwdriver
TOOLS NEEDED
Figure 1
Short
Screws

PAGE 2 OF 3 0316 IH-5598
INSTALLATION CONTINUED
3. Slide the cap catch bin onto the mounting bracket.
(See Figure 2)
4. Connect the lid by pushing the three pins into the
clips located on the cooler. (See Figure 3)
5. Flip the base upside down to install the rigid casters
using the caster mounting hardware. (See Figure 4)
6. Ensure both rigid casters are installed on the same
side of the base. (See Figure 4)
7. While the base is upside down, place the bolts
through the caster holes from the top. From the
bottom, secure the washer on the bolt followed by
the nut and tighten using a wrench and the Phillips
screwdriver. (See Figure 4)
8. Repeat on the other side of the base with the
locking casters.
9. Place cooler onto the base ensuring the Igloo logo
on the base is on the same side as the cooler opens.
(See Figure 5)
Figure 2
Figure 3
Figure 5
Figure 4 Locking
Casters Rigid
Casters
Igloo
Logo

PAGE 3 OF 3 0316 IH-5598
INSTALLATION CONTINUED
SAFETY
10. Unscrew battery cover using the Phillips screwdriver
and install four AA batteries (not included). Secure
battery cover using the Phillips screwdriver.
(See Figure 6)
Figure 6
πCHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA
1-800-295-5510
uline.com
• Do not sit on lid or stack heavy objects on lid. Doing
so could break the lid and cause bodily injury. The
lid is intended as a cover only. It was not designed
to be a seat or storage surface.
• The casters should remain locked during use to
avoid unintentional rolling or movement.
• Avoid tipping the loaded cooler. Tipping could result
in bodily injury.
• If relocation of the assembled cooler is necessary
after filling, pull by the side handles. Do not attempt
to push the cooler from the front or back side, as this
could cause tipping.
• When transporting the cooler by vehicle, separate
the cooler from the rolling base to avoid tipping the
loaded cooler.
• Not intended for use with hot liquids.
• The cooler is equipped with a hose-compatible
threaded drain plug. To drain liquid away from area
of use, attach a standard garden hose to the cooler
drain plug and direct the open end of disposal
area.
• Intended for use with ice, drinks and food products.
Not a toy and should not be used to transport other
items or small children.
• Use under adult supervision. Do not allow children
to climb on the cooler. This could create a tipping
hazard that could result in bodily injury.
• For optimum performance, do not place in direct
sunlight. Use in a shaded or covered area.
• Before and after use, empty all contents and rinse
with water.
• Mild soap and water can be used if water alone is
insufficient.
• Allow to dry thoroughly before putting into storage.
• Opening the drain plug can aid the drying process.
NOTE: Secure drain plug cap prior to use.