U-Line WINE CAPTAIN U-2115WCOL-00 Setup guide

®
2000 SERIES
U-LINE.COM
OVERLAY PANEL GUIDE
U-2175BEVCOL-00
U-2175BEVCOL-02
U-2175BEVCOL-60
BEVERAGE
CENTERS
U-2175RCGOL-00
GLASS DOOR
REFRIGERATORS
U-2115WCOL-00
U-2175WCOL-00
U-2175WCOL-02
U-2175WCOL-60
U-2275ZWCOL-00
U-2275ZWCOL-60
WINE CAPTAIN®
MODELS
The American Built-In Undercounter Leader Since 1962

u-line.com 1
Safety Alert Definitions
Throughout this guide are safety items labeled with a Danger,
Warning or Caution based on the risk type:
DANGER
!
Danger means that failure to follow this safety statement will
result in severe personal injury or death.
WARNING
!
Warning means that failure to follow this safety
statement could result in serious personal injury or
death.
CAUTION
!
Caution means that failure to follow this safety statement
may result in minor or moderate personal injury, property
or equipment damage.
Model Coverage
Safety Precautions Overlay
This guide covers the following models
U-2115WCOL-00 U-2175WCCOL-00
U-2175BEVCOL-00 U-2175WCCOL-02
U-2175BEVCOL-02 U-2175WCCOL-60
U-2175BEVCOL-60 U-2275ZWCOL-00
U-2175RCGOL-00 U-2275ZWCOL-60

2u-line.com
Overlay Preparation
Use the following instructions to create or have a wood overlay
panel created for your Wine Captain® or Beverage Center.
NOTICE
When having the frame or overlay finished with a stain, be
sure to finish both sides. The back side of the frame /
overlay may be visible through the glass while the door is
open in some installations.
1. Determine cabinet toe kick height. Measure the difference
between the surface the appliance will sit on and the bottom of
the adjacent cabinetry. Make note of this.
2. Create a frame or overlay using the dimensions provided in the
figure below.
Note: Dimensions will vary based on the levelness of the floor. If
floor is uneven, cut panel to the next longer dimension and adjust
level legs to achieve proper fit.
3. Drill holes for pivot pins, upper door hinge and lower door
hinge as shown.
9/32
See Detail C
3/4"
Detail C
Scale 2:1
Door bottom
Ø 3/8" x 1/4" deep
Chamfer 1/32" x 45°
Detail A
Scale 2:1
Door top
Ø 3/16" x 11/16" deep
9/32"
3/8"
See Detail A
Dim. B
NOTE: Front view of
wood panel with
right-hand hinge shown
(mirror image
for left-hand hinge)
Section A-A
Scale 2:1
Typ 4 places
NOTE: Final component
is only a picture frame.
No panel inside of rails.
(Excludes -60 Models)
(Excludes -60 Models)
Right-hand
isometric view
shown.
Opposite
for left-hand
A
A
Dim. A
3/4"
2-1/4"
Dimension A Table
Model Dimension A
2275ZWCOL
2175WCCOL
2175BEVCOL
2115WCOL
23-3/4"
23-3/4"
23-3/4"
14-3/4"
(See Table)
Dimension B Table
Toe KickToe Kick Dim. BDim. B
3-3/4"
3-7/8"
4"
4-1/8"
4-1/4"
4-3/8"
4-1/2"
29-3/4"
29-3/4"
29-5/8"
29-1/2"
29-3/8"
29-1/4"
29-1/4"

u-line.com 3
Prepare the New Overlay Panel
1. Place a towel, or similar, soft non-marking material out on a flat
clean surface. Be sure the material is large enough to have the
wood panel not touch the hard mating surface.
2. Lay the wood panel out with the front side of the wood facing
down.
3. Cut the foam tape in to four pieces, two pieces the width of the
overlay and two pieces the height of the overlay.
4. Remove adhesive protection strip from one piece of the cut
foam and align the edge of the foam tape to the inside edge of
the overlay as shown, adhering the foam tape to the overlay. See
below.
5. Trim each piece of tape immediately after applying it to the
overlay. Do not allow any overlapping of the foam tape. Damage
to the overlay can occur is the foam tape is not trimmed
correctly.
6. If required, attach any optional cabinet hardware to the wood
panel at this time. If an optional cabinet handle is installed, make
sure the mounting screw heads are below (countersunk) the
back surface of the overlay.
Note: After attaching the optional cabinet hardware, additional
supports may be needed to keep panel flat for next steps.
Attaching the Overlay Panel
1. Remove the top hinge pivot pin with a Phillips screwdriver and
lift the door off bottom hinge pin. Be careful not to lose the
door closer insert sets. Save pivot pin for use later. See below.
2. Carefully lay the door over the wood panel, making sure door is
oriented correctly (top of door with top of wood overlay).
3. Pull door gasket out of the groove completely. Start in the
middle and pull outward, moving towards the corners (see
below). This may take some force, but be careful not to cut or
rip the gasket.
4. After the gasket has been removed, place it on a clean, flat
surface.
5. Secure the door to the back of the wood overlay using tape.
#6 x 1" Pan Head Screws
(10 Total) Ta p e
Top Of Panel
Depending on installation
bottom of overlay may NOT
align with bottom of door

4u-line.com
6. Use the door frame holes as a guide to lightly punch pilot holes
for the 10 #6x1" pan head screws.
7. Attach the door to the overlay using #6x1" wood screws.
NOTICE
If you decide to drill pilot holes, remove the wood overlay
from the door, and do not use a drill larger than 7/64". Be
sure not to drill deeper than 3/8". The door frame and
wood overlay must be aligned properly or the door will
not operate correctly.
Note: After attaching the wood to the door, double check the
bottom pivot hole location. If the hole in the pivot bracket is
covered by any wood, chase through the hole with a 11/32" drill to
open hole in door panel. DO NOT drill deeper than 1/4".
Assembling Door to Cabinet
8. Starting at the corners and working toward the center, push the
door gasket back into place. Make sure the gasket is fully seated
on all four sides and corners.
9. Check the closure assembly on the bottom hinge to be sure it is
seated correctly in the bosses in the hinge.
10. Position door over closer. Be sure the door hinge plate holes
align with the bosses on the closer (see below). Failure to do so
will result in the door not sitting in the proper position and door
will not align correctly. (Sometimes it is helpful to open the door
180° to have the closer and pivot align correctly.)
11. Holding the door in the closed position, install the pivot post
through the top hinge into the top pivot plate. Tighten securely
with a Phillips screwdriver, making sure post is seated fully.
NOTICE
The bottom of the lower overlay panel will line up with the
bottom of the adjacent cabinetry and may not line up with
the bottom of the actual door itself. See graphic below.
Door closers
Bottom Of Frame
Door Reveal
Panel
Toe Kick

®
OVERLAY PANEL GUIDE
©2013 U-Line Corporation
Publication Number 30305 4/2013 Rev.F
The American Built-In Undercounter Leader Since 1962 U-LINE.COM
BUILDING ON THREE GENERATIONS OF INNOVATION
For over five decades and through three generations, U-Line continues to be the leader in innovation, quality and
performance in the premium built-in undercounter ice making, refrigeration and wine preservation market. U-Line
has captivated those with an appreciation for the finer things with exceptional functionality, style, inspired
innovation and attention to even the smallest details. We are known and respected for our unwavering dedication
to product design, quality and selection.
In 1962, Henry Uihlein founded U-Line Corporation as an outgrowth of Ben-Hur Freezer Company and was the first
to develop and patent an automatic stand-alone undercounter residential ice maker. His foresight and determination
to develop new ideas and to succeed when there were no clear guidelines or solutions are evident today. The newest
Uihlein generation continues to build upon the family’s innovative legacy at the Milwaukee, Wisconsin based business
by providing continuity and vision from which new designs and technology continue to be born.
Today the complete U-Line product collection includes Ice Makers, Ice Machines, Wine Captain®Models, Combo®
Models, Refrigerator / Freezers, Refrigerators, Drawer Models and Beverage Centers. The U-Line brand offers
products in the 1000 Series, 2000 Series and the Modular 3000 Series. The 1000 Series offers a more targeted
priced product with appropriate features, while the 2000 Series offers upscale features, advanced technology and
specialized product families. Our Modular 3000 Series provides sleek design and versatile temperature settings with
our U-Select®control. U-Line’s approach to its breadth of products, multiple price points and features allows a
choice and product that will fit any lifestyle.
PRODUCT INFORMATION
Complete Installation Guides, Use and Care Guides, Specifications & Features and Benefits, CAD Drawings,
Overlay Panel/Frame and Toe-Kick Specifications and Instructions, Compliance Documentation and Applicable
Energy Guides are available for reference and download at u-line.com.
SERVICE INFORMATION
Please consult your Use and Care Guide for troubleshooting information. Answers to Customer Frequently Asked
Questions are available at u-line.com under Customer Service. You may contact U-Line directly:
GENERAL INQUIRIES:
U-Line Corporation
P.O. Box 245040
Milwaukee, Wisconsin 53224-9540 U.S.A.
Phone [phone]
FAX [phone]
Email: [email protected]
u-line.com
SERVICE ASSISTANCE:
Phone [phone]
FAX [phone]
Email: onlineser[email protected]
u-lineservice.com
PARTS ASSISTANCE:
E-mail: [e-mail]
DESIGNED, ENGINEERED AND ASSEMBLED IN WISCONSIN, USA