U-Line H-670 User manual

PAGE 1 OF 4 0114 IH-670
INDUSTRIAL PLATFORM
SCALE
1-800-295-5510
uline.com
πH-670, H-747
H-794, H-4593
1. Remove scale parts from packaging.
2. Lift the Scale Pan off the Platform Base.
3. Remove the four styrofoam blocks from the Platform
Base. (See Figure 1)
4. Replace the Scale Pan.
Figure 1
Allen Wrench Power Cord Support Bracket Tower Platform Base Display Indicator
PARTS
ASSEMBLY INSTRUCTIONS

PAGE 2 OF 4 0114 IH-670
ASSEMBLY INSTRUCTIONS CONTINUED
5. Place the Scale on the stable, level surface on which
it is intended to be used.
6. Using the bubble level on the Base Bracket as a
guide, adjust the four leveling feet until scale is level.
(See Figure 2)
7. Feed the data cable from the Base Bracket through
the Tower. (See Figure 3)
8. Tighten the Base Bracket using the included Allen
Wrench. (See Figure 4)
9. Feed the data cable through the Support Bracket by
unscrewing the knob and pulling the Support Bracket
pieces apart. (See Figure 5)
10. Once data cable is threaded through Support
Bracket as shown, tighten the knob and place the
Support Bracket on the Tower. (See Figure 5)
11. Tighten the bolt at the base of the Support Bracket.
(See Figure 5)
12. Slide the Display Indicator onto the Support Bracket.
Adjust the angle of the display by loosening the
knob on the Support Bracket. Tighten the knob when
finished adjusting the angle. (See Figure 6)
13. Plug the data cable and the Power Cord into the
Display Indicator. (See Figure 7)
Figure 2
Figure 4
Figure 5
Figure 3
Figure 6
Figure 7

PAGE 3 OF 4 0114 IH-670
STABLE M+ Pcs
Pcs Kg
0CE
TR
CE
STABLE PT M+
M+
Pcs
UNITS
0R
Pcs
PT
T
charging
H-670
H-747 & H-7914
QUICK USER’S GUIDE
COUNTING FUNCTION
•Prior to use, connect the AC
adapter and monitor cable.
•This scale has fixed samples
of 10, 20, 50, and 100 pieces.
•The larger sample sizes will
provide you with a more
accurate unit weight.
1. Prior to placing any object
onto the scale, press the CE
key (1). (See Figure 8)
2. Select the fixed sample key of
10, 20, 50, 100 pieces (2).
(See Figure 8)
3. Place the requested number
of samples onto the scale.
4. Press the count key (4).
(See Figure 8)
5. Remove all parts from the
scale.
6. Place the desired number of
pieces onto the scale. This will
provide an accurate count
reading.
7. Remove all parts from the
scale.
8. For the H-670 and H-4593:
Press the UNITS key (8) to
return to the weight display
screen. (See Figure 8)
9. For the H-747 and H-794:
Press the KG key (8) to return
to the weight display screen.
(See Figure 8)
Figure 8
H-670 & H-4593
H-747 & H-794

PAGE 4 OF 4 0114 IH-670
CALIBRATION INSTRUCTIONS
NOTE: Scale can only be accurately calibrated using standard calibrated scale weights. Using
non-calibrated weights may result in inaccurate scale calibration. Nothing should be on the scale and
scale should be level.
ACTIVATE WEIGHT CALIBRATION MODE
•Turn on the scale. As scale counts down to zero, press and hold the Zero key until 02001 appears in the
display.
•Release Zero key. F0 appears in display.
•Switch the mini jumper SWA1 to “ADJ” position. Adjust is down; Lock is up. The switch is located under a
panel on the right side of the keypad housing.
•Press Enter key. Display shows ZEro.
•Press Enter key. Display shows 0---,-Ckg.
•Press UNITS or Kg key to set scale to lb or kg as needed.
•Use the Up and Enter keys to preset the weight being used to calibrate the scale. The Up key sets the
number and the Enter key moves right one digit. Example: to set a weight of 3.0 kg you would press the
Enter key three times to move right three spaces and the Up key three times to enter the number 3.
•Place your calibrated weight on the scale. Display shows WAIt.
•Scale displays weight and beeps.
•Scale is calibrated, it will now return to weighing mode automatically.
•Switch the mini jumper SWA1 back to “LOCK.”
0
UNITS
Kg
0
UNITS
Kg
0
UNITS
Kg
0
UNITS
Kg
0
UNITS
Kg
0
UNITS
Kg
0
UNITS
Kg
0
UNITS
Kg
πCHICAGO•ATLANTA•DALLAS•LOSANGELES•MINNEAPOLIS•NYC/PHILA•SEATTLE•MEXICO•CANADA
1-800-295-5510
uline.com