U-Reach Intelligent 9 Series User manual

Intelligent 9 Series
CF/CFast/CFast-Native
Duplicator & Tester
User Manual v A.01

2
Index
Product Disclaimer...............................................................................................................3
Warranty ..............................................................................................................................3
Piracy Statement ..................................................................................................................3
Before You Start ...................................................................................................................4
Notice Symbols.....................................................................................................................4
Introduction .........................................................................................................................5
Function Table......................................................................................................................8
Function Description..........................................................................................................15
1. Copy .................................................................................................................15
2. Compare ..........................................................................................................16
3. Copy+Compare ................................................................................................16
4. Media Check ....................................................................................................16
5. Information......................................................................................................20
6. Utility ...............................................................................................................20
7. Setup................................................................................................................24
8. Burn-In (Available in CF/CFast Golden Series) ..................................................28
9. Log Manager (Available in Golden Series) ........................................................31
How to use PC-Monitoring.................................................................................................32
How to Use Event Log?.......................................................................................................34
Maintenance Guide.............................................................................................................38
Q&A.....................................................................................................................................39
Specification .......................................................................................................................41
v A.01.3

3
Product Disclaimer
U-Reach is not accountable for any incidental or consequential damages, which includes,
but is not constrained to property harm, loss of time or data from use of a U-Reach product,
or any other damages attributable to product malfunction or failure (including without
limitation, those attributable to: (1) reliance of the materials provided, (2) costs of product
replacement, (3) loss of use, data or profits, (4) delays or business interruptions, (5) and any
principle of legal responsibility, arising out of or in reference to the use or overall
performance or from delays in servicing or lack of ability to render service) of any U-Reach
product. U-Reach makes every effort to ensure proper operation of all products. However,
the customer is responsible to affirm that out of the U-Reach product meets the customer’s
quality requirement. The customer further acknowledges that fallacious operation of U-
Reach product and/or software program, or hardware issues, can cause loss of data,
defective formatting, or data loading. U-Reach will make efforts to resolve or repair any
issues recognized by customer either within the warranty period or on a time and materials
basis.
Specifications and features subject to change without notice or obligation.
Warranty
U-Reach provides a basic one-year parts and labor warranty for all of its products (excluding
cables, adapters, and other consumable items). An optional extended warranty is also
available for an added cost. Telephone and email support is available for the life of the
product as defined by U-Reach.
All warranties will be restricted and defined by the market region from which customers
purchased.
Piracy Statement
U-Reach accepts no responsibility for copyright infringement or misuse of any U-Reach
equipment. Copying all forms of data: audio, video, or software without the permission of
the copyright holder is illegal. It is the sole responsibility of the user to ensure that the legal
copyrights of the copyright owners are respected.

4
Before You Start
Important Notice
⚫Carefully read the entire manual before operating.
⚫Make sure the source device is correct and functioning.
⚫Equal capacity of source and target is recommended for guaranteed data consistency.
⚫Using the Copy+Compare function provides the most flawless duplication.
⚫Damage incurred due to non-compliance with U-Reach operating instructions will void
the warranty.
⚫Store the equipment safely when not in use and keep out of the reach of children.
⚫Please turn off duplicator before replacing a socket.
⚫Never turn off the power while the firmware is updating.
⚫Use only approved, stable power sources.
⚫Use product only in a clean, dry, dust-free, and ventilated area. Liquids or foreign
debris can severely damage your duplicator.
⚫It is typical for the machine to heat up during operation.
⚫While in use, do not move the duplicator or remove devices.
⚫Static electricity may cause duplication error. Please pay attention to the duplicator’s
environment while operating equipment. Purchasing electricity elimination equipment
helps avoid shock.
Notice Symbols
Special items, procedures, or notes to be observed prior to use.
Note
Refers to related duplicator operations, special details, tips, or
suggestions for operational effectiveness.
Caution
Refers to procedures that need to be adhered to or precautions.

5
Introduction
1. Features
The new Intelligent 9 Series was designed with diversified media compatibility and high-
speed performance in mind to not only flawlessly duplicate numerous large capacity targets
that effectively meet high volume demands, but also provides helpful flash card
examinations by delivering the most accurate testing functions known today. The user-
friendly interface offers stress-free operation with no steep learning curve to climb. Its
ergonomic design facilitates efficient operation through simpler insertion and removal of
flash cards and since the new design allows for better space utilization, its helped slash
freight costs, thus ensuring a 20-80% carbon footprint reduction.
⚫Ultra-high transmission speed.
⚫Real multitask processing capability. Whether copy, compare, media check or format,
each feature is independently executed. Each flash slot has an independent processing
unit.
⚫Powerful H3/H5/H6 for speed and flash quality check.
⚫Non-PC based, with no risk of virus infection.
⚫One touch copy. Real time information will be displayed on the LCD screen.
⚫Supports Synchronous and Asynchronous copy/compare/erase/format/media
check/speed check. The status of each flash media can be viewed during copy
operation by pressing the▲▼keys.
⚫Ultra-high speed bit-for-bit hardware comparison.
⚫Various copy speed selection is available for assorted flash media quality.
⚫Special speed selection function to filter out qualified flash media during quality control
process.
⚫Burn-In test & Log Report function are built in for advanced industrial application.
(Golden Series Only)

6
2. Hardware Overview
Front View
Back View
Souce Port
LED Indicator
Green: Pass/Working
Red: Fail
Control Buttons
▲:
Forward
▼
: Backward
OK: Confirm
ESC: Escape
Power Switch
Power Supply
USB Port for PC Link

7
3. Package Contents
4. Power Adapter
Each model may require a different power adapter per its need. The following reference
table illustrate adapter requirements for each series.
Reference table (CF/CFast/CFN)
Ports
Adapter
Adapter volume needed
when copying CF
4-32
12V 5A
1
40-60
12V 9A
1
80-120
12V 12.5A
1
12V DC Adaptor x 1
Power Cord x 1
User Manual x 1
Duplicator x 1
PC-Link Software
Disc x 1
USB Cable for
PC Link x 1

8
Function Table
*Below functions and features subject to change without notice.
Silver/Golden: CF / CFast Series
Function
Description
1. Copy
Data or whole media duplication only.
2. Compare
Bit-by-bit comparison between the source and target flash medias.
3. Copy
&Compare
First copies, then compares the target to the source once duplication is
completed.
4. Media check
4.1 H3 Safe
Checks the flash’s quality by reading it. This safe check will not change
the flash’s content or format.
4.2 H5 Test
Checks the flash’s quality by reading and writing. This function will
change the flash’s content and format.
4.3 H6 Test
Checks the flash’s quality by writing and reading its empty space. This
function will not change the flash’s content or format.
4.4 Setup Range %
Sets the flash’s checking range percentage.
4.5 Setup Range MB
Sets the flash’s checking range in MB.
4.6 Set Error Limit
Sets the error tolerance range when checking the flash. (Units:
Sector/KB/MB)
4.7 Minimum Read Speed
Set the minimum read speed criteria for H3/H5/H6 checking.
4.8 Minimum Write Speed
Set the minimum read speed criteria for H5/H6 checking.
4.9 Set Capacity Limit
Sets capacity range when checking the
flash device.
4.9.1 Set Upper Limit
4.9.2 Set Lower Limit
4.9.3 Clear Limit

9
5. Information
5.1 CF Info.
This feature will show flash’s data information, file format, content size,
and capacity.
5.2 System Info.
This feature will show system information, such as, model number and
software version.
6. Utility
6.1 Do Format
6.1.1 Auto Format
Auto formats media to FAT16 or 32.
6.1.2 FAT16 Format
Formats media to FAT16.
6.1.3 FAT32 Format
Formats media to FAT32.
6.1.4 Set FAT 16 Cluster Size
Sets FAT16 Cluster size.
6.1.5 Set FAT 32 Cluster Size
Sets FAT 32 Cluster size.
6.2 Measure Speed
This function measures the flash reading and writing speed. This
function will damage the format and content.
6.3 Capacity Check (Available in CF and CFast Series)
Checks real capacity of the flash.
6.4 Quick Erase
Erases flash media content. It will keep the FAT format.
6.5 Full Erase
Fully erases, bit for bit, data on flash, including format and content.
6.6 DoD Erase
Erases flash three times complying with USA Department of Defense
(DoD) standards.
6.7 System Update
System firmware update via the flash media.
6.8 Calc. Checksum
Calculates the source’s flash media Checksum value.

10
7. Setup
7.1 Start-up Menu
Selects which function to display first upon system start up.
7.2 Copy Area
7.2.1 System and Files
Automatically analyzes source data’s format and
copies only the data area.
7.2.2 Whole Media
Copies the entire flash content, including the empty
space.
7.3 Button Sound
Enables or disables the audible beep when a button is pressed.
7.4 Target Tolerance
Sets the of capacity gap tolerance between the source and target.
Default setting is “No limit”.
7.5 Asynchronous
Enable opens Asynchronous function. Disable closes this function.
7.6 Check Before Copy
Allows user to check the flash media before duplicating.
7.7 Power Off Time Between Copy+Compare
Sets the power-off time between Copy and Compare.
7.8 Auto Start After Fill Device
Sets automatic start of copy/compare once all targets have been inserted.
7.9 Language
Sets system language.
7.10 CF Transfer Mode
Sets data transmission speed.
7.11 Monitor Device After Copy
Allows user to set a device status check after duplication.
7.12 Adjust Clock (Available in Golden Series)
Adjusts the time clock displayed on the LCD monitor.
7.13 Use Port 2 as Compare Source (Available in Golden Series)
Double-source setting. When this function is enabled, Port 2 will
become the comparison source.
7.14 Advanced Setup
(Available in Golden Series)
7.14.1 LED in Factory Mode
LED in Factory Mode Sets the LED mode.
7.15 Set to Default
Reverts everything back to the original manufacturer settings.

11
8. Burn-In
8.1 Burn-In (Copy+Comp)
Performs Burn-in test on USB targets by copying & comparing the
source.
8.2 Burn-In (Auto Data)
Automatically performs the Burn-in test on USB targets.
8.3 Set Burn Time
Sets the Burn-In test duration.
8.4 Set Loop Count
Sets the Burn-In test loop count. Each test loop contains a writing &
comparing test.
8.5 Set Test Range
Sets the flash card test range.
8.6 Set Bad Limit
Sets the Burn-In test error tolerance.
8.7 Set Data Pattern
Sets the burn-in test writing pattern.
8.8 Compare Count Per Loop
Sets the data reading count per loop.
8.9 Power Off Between Loop
Sets the power off time between each data writing and reading loop.
8.10 Compare Count Per Copy
Sets the burn-in test data reading count per loop.
(copy+compare)
9. Log
Manager
(Available in
Golden Series)
9.1 Out Today Report
Outputs today’s log records.
9.2 Out Recent Report
Outputs recent log records.
9.3 Out Period date
Outputs log records for user defined time periods.
9.4 Advanced Function
*Access to this function
requires a password*
9.4.1 Clear ALL Log
Clears all log records with password
entry.
9.4.2 Setup Password
Sets the password for clearing log
records.

12
Silver/Golden: CFast-Native (CFN) Series
Function
Description
1. Copy
Data or whole media duplication only.
2. Compare
Bit-by-bit comparison between the source and target flash medias.
3. Copy
&Compare
First copies, then compares the target to the source once duplication is
completed.
4. Media check
4.1 H2 Test
Checks the flash’s quality by reading and writing and leaves the written
pattern.
4.2 H2 + Format
Checks the flash’s quality by reading and writing and then executes
format.
4.3 H5 + Format
Checks the flash’s quality by writing and reading and then executes
format.
4.4 Setup Range %
Sets the flash’s checking range percentage.
4.5 Setup Range MB
Sets the flash’s checking range in MB.
4.6 Set Error Limit
Sets the error tolerance range when checking the flash. (Units:
Sector/KB/MB)
4.7 Minimum Read Speed
Set the minimum read speed criteria for H3/H5/H6 checking.
4.8 Minimum Write Speed
Set the minimum read speed criteria for H5/H6 checking.
4.9 Low Speed Tolerance Time
Sets the tolerance time for “minimum read/write speed.”
4.10 Set Capacity Limit
Sets capacity range when checking the
flash device.
4.10.1 Set Upper Limit
4.10.2 Set Lower Limit
4.10.3 Clear Limit

13
5. Information
5.1 CFast Info.
This feature will show flash’s data information, file format, content size,
and capacity.
5.2 System Info.
This feature will show system information, such as, model number and
software version.
6. Utility
6.1 Do Format
6.1.1 Auto Format
Auto formats media to FAT16 or 32.
6.1.2 FAT16 Format
Formats media to FAT16.
6.1.3 FAT32 Format
Formats media to FAT32.
6.1.4 Set FAT 16 Cluster Size
Sets FAT16 Cluster size.
6.1.5 Set FAT 32 Cluster Size
Sets FAT32 Cluster size.
6.2 Measure Speed
This function measures the flash reading and writing speed. This
function will damage the format and content.
6.3 Quick Erase
Erases flash media content. It will keep the FAT format.
6.4 Full Erase
Fully erases, bit for bit, data on flash, including format and content.
6.5 DoD Erase
Erases flash three times complying with USA Department of Defense
(DoD) standards.
6.6 Calc. CRC64
Calculates the CRC64 value of the source port’s flash media.
6.7 System Update
System firmware update via the flash media.
7. Setup
7.1 Start-up Menu
Selects which function to display first upon system start up.
7.2 Copy
Area
7.2.1 System and Files
Automatically analyzes source data’s format and copies
only the data area.

14
7. Setup
7.2.2 Whole Media
Copies the entire flash content, including the empty space.
7.3 Button Sound
Enables or disables the audible beep when a button is pressed.
7.4 Target Tolerance
Sets the of capacity gap tolerance between the source and target.
Default setting is “No limit”.
7.5 Asynchronous
Enable opens Asynchronous function. Disable closes this function.
7.6 Check Before Copy
Allows user to check the flash media before duplicating.
7.7 Power Off Time Between Copy+Compare
Sets the power-off time between Copy and Compare.
7.8 Auto Start After Fill Device
Sets automatic start of copy/compare once all targets have been inserted.
7.9 Language
Sets system language.
7.10 Monitor Device After Copy
Allows user to set a device status check after duplication.
7.11 Use Port 2 as Compare Source (Available in Golden Series)
Double-source setting. When this function is enabled, Port 2 will
become the comparison source.
7.12 Adjust Clock (Available in Golden Series)
Adjusts the time clock displayed on the LCD monitor.
7.13 Set to Default
Reverts everything back to the original manufacturer settings.
8. Log
Manager
(Available in
Golden Series)
8.1 Out Today Report
Outputs today’s log records.
8.2 Out Recent Report
Outputs recent log records.
8.3 Out Period date
Outputs log records for user defined time periods.
8.4 Advanced Function
*Access to this function
requires a password*
8.4.1 Clear ALL Log
Clears all log records with password entry.
8.4.2 Setup Password
Sets the password for clearing log records.

15
Function Description
1. Copy
Step 1: Prepare source and target devices.
Step 2: Insert source and target devices.
Step 3: Proceed to copy.
Scroll to select "1. Copy", then press "OK" to start the duplication process.
The information below states what is displayed on the LCD during duplication.
Step 4: Copy Completed!
The quantity of passed or failed target device(s) and the copied duration will be displayed
on the LCD after duplication completes.
Note
Recommendation: Target device(s)’ capacity must be equal to or larger
than the source device capacity.
Note
The number of working/connected targets will be displayed on LCD. Press
"OK" to start.
Note
⚫Before duplication, select the data area at "7.2 Copy area"
⚫Press ▲▼ together for 5 seconds to stop operation on the slowest
device.
⚫Press “ESC” for 5 seconds to stop all the copy jobs.
Caution
It is recommended to reboot the machine after manually stopping the
copy.
USB3.1 Duplicator
1. Copy (Data)
Copy 7695M
3% 0:27 (3)270M
(3) indicates Port #3 is the slowest.

16
2. Compare
The compare function checks the accuracy of copy result.
Scroll to select "2. Compare", then press "OK" to start the
verification process.
3. Copy+Compare
Sequentially automates from Function 1, Copy to Function 2, then Compare.
Scroll to select "3. Copy+Compare", then press "OK" to start
the automated duplication and verification process.
4. Media Check
Note
⚫Functions mentioned with “Overwrite” will change the content and
format of flash media, please do not execute this function if there is
important data stored in it.
⚫You can set the checking range in [4. Media Check >> Setup Range].
⚫To protect source data, the system default setting will not execute this
function on the master device.
➢CF/CFast Series
4.1 H3 Safe
This function reads the flash media to assess its quality. After executing this function, the
flash’s bad sector quantity and reading speed will be displayed.
Use the ▲▼ buttons to view the status of each port.
Note
(For CFN only)
The CRC64 value will be displayed on the LCD after duplication completes.
Note
⚫If flash card is removed during copy process, the system will stop
immediately, and red light will illuminate to notify user the copy has
failed. Removing the flash card during copy is strongly discouraged as
it will damage the flash card.
⚫Backup the data on target flash cards before starting the copying
process as any pre-existing data will be lost once copy is complete.
USB3.1 Duplicator
2. Compare
USB3.1 Duplicator
3. Copy+Compare

17
Note
⚫This function will not alter the content or format.
⚫You can set the checking range in [4. Media Check >> Setup Range].
4.2 H5 Test
This function performs a read and write test to determine the flash’s quality. The flash’s
original data will be erased during this test. Use the ▲▼buttons to view the status of each
port.
Note
The flash device will be formatted at FAT 16/32 once testing is complete.
4.3 H6 Test
This function performs a read and write test on the empty space to determine the flash’s
quality. The flash’s original data will not be erased during this test.
Note
⚫This function supports FAT16/32 format only.
⚫This function will NOT alter the flash’s content.
[#02] Bad: 0 3871M
R: 14.2MB/s
Bad Sector
Test Capacity
Reading Speed
Pass: 1 H3 SafeTest
Fail: 0 0
Pass Quantity
Fail Quantity
[#02] Bad:0 3871M
W: 7.2M/s R:14.2M/s
Pass:1 H6 Test
Fail: 0 0
Pass: 1 H5 Test
Fail: 0 0
Pass Quantity
[#02] Bad: 0 3871M
W:7.2 M/s R: 14.2M/s
Bad Sector
Test Capacity
Writing Speed
Reading Speed
Fail Quantity

18
➢CFast-Native(CFN) Series
4.1 H2 Test
This function performs a read and write test to determine the flash’s quality. After H2 Test,
the device will contain H2 files which can be verify again through computer’s software if
necessary.
4.2 H2 + Format
This function performs a read and write test to determine the flash’s quality. After H2 Test,
it will execute format to delete the H2 files.
4.3 H5 + Format
This function performs a read and write test to determine the flash’s quality. After H5 Test,
it will execute format.
4.4 Setup Range %
This function sets the quality check capacity range. Use the▲▼buttons to set the range
from 1 to 100%. The higher the percentage, the longer it takes.
4.5 Setup Range MB
This function sets the quality check capacity range in MB. Use the▲▼buttons to set the
range from 1MB to 9000MB.
Note
The duplicator will abide by whichever was set last if both Range% and
Range MB are set.
4.6 Setup Error Limit
This function sets the error tolerance range while checking the flash. Use the ▲▼ buttons
to set the error limit value. Select units to use (KB or MB), then select the value.
[Setup Range]
100%
[Setup Range MB]
2000MB

19
4.7 Minimum Read Speed
This function can be used to select the flash media whose reading speed is too slow. Users
can set an expected minimum reading speed for media check, so the flash media that
doesn’t reach the minimum speed value will be identified.
4.8 Minimum Write Speed
This function can be used to select the flash media whose writing speed is too slow. Users
can set an expected minimum writing speed for media check, so the flash media that
doesn’t reach the minimum speed value will be identified.
Note
When the red-light illuminates to indicate that an error has occurred, use
the▲▼buttons to view the error information.
4.9 Low Speed Tolerance Time (Available in CFast-Native(CFN) Series)
This function can set the tolerance time for “minimum read/write speed.”Within the
tolerance time, if the instantaneous speed is always lower than the minimum speed value,
the flash media will be identified.
The default setting is 30 seconds.
4.10 Set Capacity Limit
This function is used to set the flash device testing capacity limit. Users can set an upper
and lower limit of the flash capacity. To reset, select “clear limit”.
[Setup Unit]
MB
[Setup Error Limit]
9000MB
[Minimum Read Speed]
10.0MB/Second
[Minimum Write Speed]
10.0MB/Second
[Set Capacity Limit]
1. Set Upper Limit
[Set Capacity Limit]
2. Set Lower Limit

20
5. Information
5.1 CF/CFast Info.
This setting displays the flash media’s basic information such as file format, content size,
and total capacity.
Use the ▲▼buttons to view the information of each flash media, source included.
Note
Using this function will not delete the flash media content or format.
5.2 System Info.
This function displays system information such as model number and software version.
6. Utility
6.1 Do Format
6.1.1 Auto Format
This function formats flash into FAT. Plug in the flash media and press "OK". The system will
automatically detect its capacity, then format the media per its capacity.
⚫If the flash media format is already FAT16 or FAT32, the format function won’t alter its
original format.
⚫If the original flash media is not FAT format, i.e. NTFS, Linux or FAT multi-partition.
Note
The source port will not perform any formatting because this function will
delete the flash media’s data.
[#01] 116G
FAT32
15M
Total Capacity of the Device
Data Size
CFast Dupe 1-15
Ver: 2.41.4
Press ▼for further information