Uberhaus 72255168 User manual

Model / Modèle 72255168
Hard Top Gazebo
User Manual p. 2
Abri-soleil à toit rigide
Guide de l'utilisateur p.27

Please check yourprovincial and local regulationsprior to installing the gazebo. installing the gazebo.
Important Safety Instructions
WARNING! To reduce the risk of serious injury or damage to equipment, read all
the following safety instructions before assembling and using the gazebo.
Failure to follow these warnings may result in serious injury or death.
being assembled.
The assembled gazebo should be located at least 6feet (2 m) from any obstruction, such as fences,
garages, houses, overhanging branches, laundry lines or electrical wires.
Consult with your local municipal office for specific requirements.
secure the gazebo to the ground. Do not assemble the
gazebo on sandy, muddy or loose soil, as stakes do not have enough holding power in these types of soil. If you wish
to secure the gazebo to a wood deck or to a concrete surface, use anchors suited to these surfaces
T assemble this item alone. Make sure you have the help of at least 3 people for safe
assembling or moving of the gazebo.
frequent severe weather, securing the gazebo to a deck, concrete patio or footings should be considered.
or disassemble the gazebo in order to avoid damages.
thicker than 4 inches (10 cm). In order to avoid damages, use a plastic snow shovel to remove snow and ice
buildup from the roof and keep away from falling debris.
construction and not designed to withstand harsh weather, including high wind, or heavy rain and snow.
Some jurisdictions may require permits for installation and use. Some special procedures may be valid in
CAUTION
harsh weather (e.g., thunderstorms, high winds, hail, heavy snow, etc.). In
these conditions, it might tip over and could cause serious injury to bystanders. Any damage or injury caused by these
conditions is not covered by the warranty.
to trees or a sloped roof. Snow and ice may slide onto the gazebo and cause it
to collapse.
any of the following conditions or similar conditions:
1. Visible movement of support members, roofing panels or sagging roofline.
2. Vreaks or audible noise from the gazebo.
3. Vracks, fractures or malformation of support member or roof panels.
4. Damaged or missing fasteners.
DO NOT use a ladder leaning against thegazebo or climb onto the roof.
dry location.
-2-
Keep all children and pets away from the assembly area. Children and pets should be supervised while gazebo is
This product is for domestic outdoor use (for providing shade) only.
ALWAYS DISASSEMBLE the gazebo before experiencing heavy wind conditions, as it is a semi-permanent
your area.
(anchors not included).
Keep the gazebo away from heat or a flame source.
If the gazebo won't be used for a long period of time (e.g., during winter time), disassemble and store it in a clean,

PREPARATION
Required for assembly:
Before beginning assembly of this product, make sure all parts are present. Compare parts with the package contents
list and hardware contents list.
If any part is missing or damaged, do not attempt to assemble the product.
Have a team of 4 or more people when assembling or moving the product.
Estimated assembly time: 3 to 4 hours.
CARE AND MAINTENANCE
accessories are treated with rust inhibiting paint that protects it from
rusting. However, due to the nature of steel, surface oxidation (rusting) will occur if these protective coatings are
scratched. This is not a defect and thus not covered by the warranty.
To minimize this condition, we recommend care when assembling and handling the product to prevent scratching
the paint. Should any scratching or damage occur, we recomm end immediate touch-up with rust inhibiting paint.
Surface rust can also be easily removed with a very light application of regular cooking oil. If surface oxidation (rusting)
occurs and if no preventive measure is taken, the oxidation may start dripping onto the deck or patio and
cause damaging stains, which may be difficult to remove.
This damage can be prevented if the above-mentioned measures are taken to keep the gazebo’s frame from oxidizing.
ive cleaners on the roof or frame parts.
-3-
Keep the User Manual for future reference.

Left-Long Lintel
Right-Long Lintel
Left-Short Lintel
Right-Short Lintel
“L” Connector
Corner Cover
Lintel Cover
Connection Piece
Post
Base
Base Cover
Slanting Bar
Connector
Support Bar
Long-Big Top Bar
Short-Big Top Bar
Small Lintel #1
Small Lintel #2
Small Top Connector
Small Top Support
Beam
Small Top Support
Beam
Long-Top Bar
Short-Top Bar
A1
A2
A3
A4
B
C1
C2
C3
D
E
F1
F2
G
H
I1
I2
J1
J2
K
L1
L2
M
N
2
2
2
2
4
4
4
4
6
4
4
4
4
8
2
2
2
2
1
2
2
4
6
Parts List
-4-
Corner Cover

Middle-Big Roof Top Beam
Big Roof Top Beam
Middle-Big Roof Top Beam
Long-Big Roof Top Beam
Long-Big Roof Top Beam
P1
P2
Q1
Q2
R
1
2
3
4
5
6
7
8
4
4
4
4
6
2
4
4
2
4
4
2
2
-5-
Short-Big Roof Top
Beam
Short-Big Roof Top
Beam
O1
O2
4
4

Bolt/Plastic
Washer (M6*25)
Screw (M4*15)
Bolt/Flat washer/
Nut (M6*55)
Bolt/Flat Washer/Nut/
Plastic Nut Cap (M6*32)
Bolt/Plastic
Washer (M6*40)
Bolt (M6*15)
Bolt/Flat
Washer (M6*15)
Small Top Roof Cover
Small Top Cover
Mosquito Netting
Plastic Cap
Big Top Panel Cover
Top Panel Cover
S
T
U
V
W
X
Y
2
2
4
4
6
1
1
4
8
AA
BB
CC
DD
EE
FF
GG
HH
II
270
16
21
8
12
8
16
Hardware List
-6-
4
2
JJ
2

E
E
E
E
E
F1
F2
AA
AA
-7-
1. Insert the Base Cover (F2) into the Post (E), and then connect the Base (F1) to the Post (E)
by Bolt (AA). Connect the other Posts in the same way. When all the Posts are ready, place them
in position as shown.

A1
A2
A3
A4
A3
A4
A1
A2
A2
A2
A1
A1
B
D
AA
AA
AA
-8-
A3
A4
AA
2. Connect the Left-Long Lintel (A1) and Right-Long Lintel (A2) with the "L" Connector (B) by
Bolt (AA), then attach the Connection Piece (D) to Long Lintel (A1/A2) by Bolt (AA). Connect the
Left-Short Lintel (A3) and Right- Short Lintel (A4) with the "L" Connector (B) by Bolt (AA), and at
the same time attach the Connection Piece (D) to the Short Lintel (A3/A4).

A3
A2
A2
A3
A3
A4
A1
BB
BB
-9-
3. Connect the Right-Long Lintel (A2) to the Post (E) by Bolt (BB) and Bolt (AA).
Connect the Left-Short Lintel (A3) to the Post (E) by Bolt (BB) and Bolt (AA). Connect the Lintel
(A1/A4) to the Post (E) in the same way.
AA
AA
A2
A3
E

A2
A3
A2 A3
E
E
E
H
H
AA
AA
AA
AA
-10-
4. Attach the Slanting Bar Connector (G) to the
post (E) by Bolt (AA).
5. Connect the Support Bar (H) to the Right-Long
Lintel (A2) and the Post (E) by Bolt (AA). Connect
the Support Bar (H) to the Left-Short Lintel (A3) and
Post (E) by Bolt (AA). Connect the other KEEP
HIGHLIGTED TEXT TOGETHER in the same way.
A2
A3
G
E
AA