Ubiquiti Amplifi AFi-LR User manual

HOME WI-FI PERFECTED™MODEL: AFi-LR
QUICK START GUIDE

Getting Started
Thank you for purchasing the AmpliFi™LR Home Wi-Fi
System. To get started, download and install the AmpliFi
app from the App Store or Google Play™Store.

Package Contents
Router Mesh Points
(Qty. 2)
Power Adapter Ethernet Cable Quick Start Guide

Hardware Overview
Router Front
Remove the electrostatic sticker from the front of
the AmpliFi Router.
The front of the AmpliFi Router features a
full-color touchscreen display.
The bottom of the AmpliFi Router features an
LED with a brightness setting congurable in
the AmpliFi app. By default, the LED is fully lit
when congured and ready for use.

Router Back
1 2
3 4
1-4 Four Gigabit Ethernet ports available to
connect 10/100/1000Mbps wired network
devices to the Internet.
Connects to the broadband modem provided
by your ISP (Internet Service Provider).
Reserved for future use.
The Power Adapter connects to this port.

Mesh Point
Signal LEDs
Magnetic Connector
Mesh Point Base
Adjustable Antenna

Installing the Router
iPhone® Users: Ensure that Bluetooth is enabled.
Android™Users: Ensure that Wi-Fi is enabled.
1 Launch the AmpliFi app.

2 Power o your broadband modem.

3 Connect one end of the Ethernet Cable to your
broadband modem and the other end to the
Internet port on the AmpliFi Router.

4 Connect the Power Adapter to the power port on
the AmpliFi Router.

5 Connect the Power Adapter to a power outlet.

6 Power on your broadband modem.

7 Follow the on-screen instructions to congure your
AmpliFi Router.

Installing the Mesh Points
Find a suitable location for each Mesh Point with an
accessible power outlet. The Mesh Points should be
placed in dierent directions between the Router and the
areas farthest from the Router.

1 Plug the Mesh Point into a power outlet.
If a Mesh Point is powered on and does not
appear online in the app, the signal is too weak
and the Mesh Point should be relocated closer to
the Router.

2 After about a minute, all ve signal LEDs should be
lit solid once the Mesh Point is connected to the
AmpliFi Router.

3 The Mesh Point antenna can be adjusted to provide
optimal signal coverage for your location.

Resetting to Factory Defaults
If the AmpliFi Router
administration password is
lost, factory default settings
can be restored by using an
object such as a straightened
paper clip or pin to press the
Reset located on the bottom
of the AmpliFi Router for
approximately 10 seconds until
the LED turns o.
If the AmpliFi Router is
reset, all MeshPoints
should also be reset
using the same method.
Router
Reset
Mesh Point
Reset

System Specications
Max. TX Power 26 dBm
Radios 4
MIMO Chains 10
Speed 2.35 Gbps
Range 20,000 sq. ft
ESD/EMP Protection ± 24kV Air/Contact
Buttons Reset
Antennas (3) Dual-Band Antennas
Display 1.6"(40.6 mm) Diagonal, 240 x 240, 212 ppi,
G+F Touch, Full Color
Wi-Fi Standard 802.11ac
Power Save Supported
Wireless Security WPA2-PSK AES/TKIP
OperatingTemperature 14 to 131°F (-10 to 55°C)
Operating Humidity 5 to 95% Noncondensing
Certications FCC / CE / IC
Supported Data Rates
802.11ac 13 Mbps to 1300 Mbps (MCS0 - MCS9, VHT 20/40/80)
802.11n 6.5 Mbps to 450 Mbps (MCS0 - MCS23, HT 20/40)
802.11a 6, 9, 12, 18, 24, 36, 48, 54 Mbps
802.11b 1, 2, 5.5, 11 Mbps
802.11g 6, 9, 12, 18, 24, 36, 48, 54 Mbps