Ubiquiti EdgeSwitch ES-10XP Guide

18.02.2020 ES-10XP Quck Start Gude
https://dl.ubnt.com/qsg/ES-10XP/ES-10XP_EN.html 1/15
EdgeSw  tch 10XP Wall Mount Screws (Qty. 2) Wall Mount Anchors (Qty. 2)
Ground Screw Power Adapter* (24V, 2.5A) Power Cord*
Cable Cl  p
Package Contents
* Included only  n the s  ngle-pack of the ES-10XP
Installat  on Requ  rements
Wall-mount  ng (opt  onal)
Dr  ll w  th 6 mm dr  ll b  t
Ph  ll  ps screwdr  ver
For  ndoor appl  cat  ons, use Category 5 (or above) UTP cabl  ng approved for  ndoor
use.
ES-10XP Qu  ck Start Gu  de

18.02.2020 ES-10XP Quck Start Gude
https://dl.ubnt.com/qsg/ES-10XP/ES-10XP_EN.html 2/15
System LED
For outdoor appl  cat  ons, sh  elded Category 5 (or above) cabl  ng should be used for
all w  red Ethernet connect  ons and should be grounded through the AC ground of
the power supply.
We recommend that you protect your networks from harmful outdoor env  ronments
and destruct  ve ESD events w  th  ndustr  al-grade, sh  elded Ethernet cable from
Ub  qu  t  . For more deta  ls, v  s  t: u  .com/toughcable
Note: Although the cabl  ng can be located outdoors, the EdgeSw  tch  tself
should be housed  ns  de a protect  ve enclosure.
Hardware Overv  ew
Flash  ng Wh  te Bootup  n Progress
Wh  te
Ready for Use
Not Connected to Ub  qu  t  ® Network Management
System (UNMS™)
Blue Ready for Use
Connected to UNMS
Steady Blue w  th
Occas  onal Flash  ng
Ready for Use
Unable to Connect to UNMS
Qu  ckly Flash  ng Blue Used to Locate a Dev  ce  n UNMS
Alternat  ng Blue/Wh  te F  rmware Upgrade  n Progress
ES-10XP Qu  ck Start Gu  de

18.02.2020 ES-10XP Quck Start Gude
https://dl.ubnt.com/qsg/ES-10XP/ES-10XP_EN.html 3/15
RJ45 PoE LED (Ports 1 - 8)
RJ45 Speed/L  nk/Act  v  ty LED (Ports 1 - 8)
SFP L  nk/Act  v  ty LED (Ports 9 - 10)
RJ45 (Ports 1 - 8)
SFP (Ports 9 - 10)
Reset Button
Power
Off No Power over Ethernet
Green 24V Power over Ethernet
Off No L  nk
Amber L
 nk Establ  shed at 10/100 Mbps
Flash  ng Ind  cates Act  v  ty
Green L
 nk Establ  shed at 1000 Mbps
Flash  ng Ind  cates Act  v  ty
Off No L  nk
Green L
 nk Establ  shed at 1 Gbps
Flash  ng Ind  cates Act  v  ty
RJ45 ports support 10/100/1000 Ethernet connect  ons and 24V Pass  ve Power over
Ethernet (PoE) output.
Hot-swappable SFP ports support 1 Gbps connect  ons. If you use a copper Ethernet
module (example: UF-RJ45-1G), power off the EdgeSw  tch before  nsert  on;
otherw  se there may be a dev  ce reboot.
To reset to factory defaults:
1. D  sconnect power from the EdgeSw  tch.
2. Reconnect power wh  le hold  ng the Reset button. The port LEDs w  ll l  ght up  n
sequent  al order (th  s takes approx  mately f  ve seconds).
3. When the port 1 LED ashes aga  n, release the Reset button.
Connect the  ncluded Power Adapter to the Power port.
ES-10XP Qu  ck Start Gu  de

18.02.2020 ES-10XP Quck Start Gude
https://dl.ubnt.com/qsg/ES-10XP/ES-10XP_EN.html 4/15
Ground  ng Po  nt
Ground bond  ng po  nt for an opt  onal ground w  re.
Hardware Installat  on
The opt  onal EdgeRouter™ Rackmount K  t, model ER-RMKIT,  s sold separately.
WARNING: The EdgeSw  tch ES-10XP must not be stacked. Do not place  t on
top of another sw  tch. Do not place anyth  ng on top of the ES-10XP.
Wall Mount  ng
1.
2.
ES-10XP Qu  ck Start Gu  de

18.02.2020 ES-10XP Quck Start Gude
https://dl.ubnt.com/qsg/ES-10XP/ES-10XP_EN.html 5/15
3.
4.
ES-10XP Qu  ck Start Gu  de

18.02.2020 ES-10XP Quck Start Gude
https://dl.ubnt.com/qsg/ES-10XP/ES-10XP_EN.html 6/15
Ground  ng the EdgeSw  tch (Recommended)
The Power Adapter grounds the dev  ce; however, you can add opt  onal ESD ground  ng
for enhanced ESD protect  on (ground w  re not  ncluded).
Opt  onal
ES-10XP Qu  ck Start Gu  de

18.02.2020 ES-10XP Quck Start Gude
https://dl.ubnt.com/qsg/ES-10XP/ES-10XP_EN.html 7/15
Connect  ng Power
1.
2.
ES-10XP Qu  ck Start Gu  de

18.02.2020 ES-10XP Quck Start Gude
https://dl.ubnt.com/qsg/ES-10XP/ES-10XP_EN.html 8/15
Connect  ng Ethernet
Us  ng SFP Ports
1.
2.
3.
ES-10XP Qu  ck Start Gu  de

18.02.2020 ES-10XP Quck Start Gude
https://dl.ubnt.com/qsg/ES-10XP/ES-10XP_EN.html 9/15
For  nformat  on about compat  ble f  ber SFP modules, v  s  t:
ubnt.l  nk/SFP_DAC_Compat  b  l  ty
Access  ng the Conf  gurat  on Interface
The EdgeSw  tch  s set to DHCP by default, so  t w  ll try to automat  cally obta  n an IP
address. If that fa  ls, then  t w  ll use the default fallback IP address, 192.168.1.20.
Proceed to the appropr  ate sect  on, DHCP or “Fallback IP Address” :
DHCP
Use one of the follow  ng methods:
Set up the DHCP server to prov  de a spec  f  c IP address to the EdgeSw  tch based on
 ts MAC address (on the label).
Let the EdgeSw  tch obta  n an IP address and then check the DHCP server to see
wh  ch IP address was ass  gned.
To log  n, follow these steps:
1. Launch your web browser. Type the appropr  ate IP address  n the address f  eld. Press
enter (PC) or return (Mac).
2. Enter ubnt  n the Username and Password f  elds. Cl  ck S  gn In.
ES-10XP Qu  ck Start Gu  de

18.02.2020 ES-10XP Quck Start Gude
https://dl.ubnt.com/qsg/ES-10XP/ES-10XP_EN.html 10/15
The EdgeSw  tch Conf  gurat  on Interface w  ll appear. Custom  ze add  t  onal sett  ngs as
needed. For 24V Pass  ve PoE conf  gurat  on, refer to “Conf  gur  ng PoE Sett  ngs” . For
more  nformat  on, refer to the EdgeSw  tch documentat  on, wh  ch  s ava  lable at
u  .com/download/edgemax
Fallback IP Address
1. Ensure that your computer (or other host system)  s connected to the EdgeSw  tch.
2. Conf  gure the Ethernet adapter on your host system w  th a stat  c IP address on the
192.168.1.x subnet.
3. Launch your web browser. Type the appropr  ate IP address  n the address f  eld
(192.168.1.20  s the default fallback IP address). Press enter (PC) or return (Mac).
4. Enter ubnt  n the Username and Password f  elds. Cl  ck S  gn In.
5. The EdgeSw  tch Conf  gurat  on Interface w  ll appear. Cl  ck the System Sett  ngs tab.
ES-10XP Qu  ck Start Gu  de