Ubiquiti EdgeSwitch 5XP User manual

EdgeSwitch 5XP Screws (Qty. 2) Anchors (Qty. 2)
Power Adapter (24V, 2.5A) Power Cord
Package Contents
Installation Requirements
Drill, 6 mm drill bit, and Phillips screwdriver (wall-mounting)
For outdoor applications, shielded Category 5 (or above) cabling should be used for all
wired Ethernet connections and should be grounded through the AC ground of the power
supply.
We recommend that you protect your networks from harmful outdoor environments and
destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For
more details, visit
ui.com/toughcable
IMPORTANT: Although the cabling can be located outdoors, the EdgeSwitch itself
should be housed inside a protective enclosure.
WARNING: To reduce the risk of re or electric shock, do not expose this
EdgeSwitch to rain or moisture.
Hardware Overview
ES-5XP Quick Start Guide

Management Power/Link LED
RJ45 PoE LED (Ports 1 - 5)
RJ45 Speed/Link/Act LED (Ports 1 - 5)
Management Port
USB Port
RJ45 (Ports 1 - 5)
Off No Power/No Link
Amber
After bootup, the LED indicates power. After an initial link
is established, the LED indicates a 10/100 Mbps
connection. If the link terminates, the LED turns off until a
link is re-established. If the unit reboots, the LED will
again indicate power until a link is established.
Off No Power over Ethernet
Green 24V Power over Ethernet
Off No link
Amber Link established at 10/100 Mbps
Amber Flashing Link activity at 10/100 Mbps
Green Link established at 1000 Mbps
Green Flashing Link activity at 1000 Mbps
10/100 Mbps port used to access the EdgeSwitch Conguration Interface.
Reserved for future use.
ES-5XP Quick Start Guide

Reset Button
Power
10/100/1000 Mbps ports for switching and PoE (also available for management by
default).
To reset to factory defaults, press and hold the Reset button for more than 10 seconds
while the unit is powered on.
Connect the included Power Adapter to the Power port.
Hardware Installation
Place the EdgeSwitch on a bench top or other at surface.
WARNING: FAILURE TO PROVIDE PROPER VENTILATION MAY CAUSE FIRE HAZARD.
KEEP AT LEAST 20 MM OF CLEARANCE NEXT TO THE VENTILATION HOLES FOR
ADEQUATE AIRFLOW.
Wall-Mounting
1.
2.
ES-5XP Quick Start Guide

3.
ES-5XP Quick Start Guide

4.
ES-5XP Quick Start Guide

Grounding the EdgeSwitch (Optional)
The EdgeSwitch is grounded through the Power Adapter; however, you can add optional ESD
grounding for enhanced ESD protection.
1.
2.
ES-5XP Quick Start Guide

Connecting Power
1.
2.
Connecting Ethernet
1.
ES-5XP Quick Start Guide

2.
Note: PoE is disabled by default on all numbered ports and is not available on the
Management port. To enable PoE on the appropriate ports, use the Ports tab in the
Conguration Interface.
Accessing the Conguration Interface
Connect to the Conguration Interface:
1. Ensure that your computer (or other host machine) is connected to the Management port
on the EdgeSwitch.
Note: By default, you can congure the EdgeSwitch via any port; however, we
recommend the Management port. (Access to the Conguration Interface can be
limited to the Management port only. You can congure this setting on the Device
tab.)
2. Congure the Ethernet adapter on your host system with a static IP address on the
192.168.1.x subnet (e.g., 192.168.1.100).
3. Launch your web browser. Type https://192.168.1.20 in the address eld. Press enter (PC)
or return (Mac).
ES-5XP Quick Start Guide

4. Enter ubnt in the Username and Password elds. Click Login.
The Conguration Interface will appear and allow you to customize your settings. You can
enable PoE on the Ports tab.
You can also manage your device using the Ubiquiti® Network Management System. UNMS™
lets you congure, monitor, upgrade, and back up your devices using a single application.
Specications
ES-5XP
Dimensions 197 x 87.5 x 27.3 mm
(7.76 x 7.28 x 1.61")
Weight 250 g
(8.82 oz)
Power Input 24VDC, 2.5A Power Adapter (Included)
Max. Power Consumption 60W
PoE Out Voltage Range 22-24VDC
Max. PoE Wattage Per Data Port 11.5W
ESD Rating ±24 kV Air/Contact
PoE Method Passive
Button Reset
USB Port 2.0 Type A (Reserved for Future Use)
Processor MIPS 24K, 400 MHz
System Memory 64 MB
Code Storage 8 MB
PoE Congurable Per Port
Management Port N/A
ES-5XP Quick Start Guide

ES-5XP
Data Ports Off/24V
LEDs Per Port
Management Port Power/Link
Data Ports PoE, Speed/Link/Activity
Networking Interfaces
Management Port (1) 10/100 Ethernet Port
Data Ports (5) 10/100/1000 Ethernet Ports
Operating Temperature -25 to 55° C
(-13 to 131° F)
Operating Humidity 90% Noncondensing
Certications CE, FCC, IC
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specied by the manufacturer.
WARNING: Failure to provide proper ventilation may cause re hazard. Keep at least 20 mm of
clearance next to the ventilation holes for adequate airow.
WARNING: To reduce the risk of re or electric shock, do not expose this product to rain or
moisture.
WARNING: Do not use this product in location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote risk of
electric shock from lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the
manufacturer’s label. Connection to a different power source than those specied may result in
improper operation, damage to the equipment or pose a re hazard if the limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided only by a
qualied service technician.
3. This equipment is provided with a detachable power cord which has an integral safety ground wire
intended for connection to a grounded safety outlet.
a. Do not substitute the power cord with one that is not the provided approved type. Never use an
adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire.
b. The equipment requires the use of the ground wire as a part of the safety certication, modication
or misuse can provide a shock hazard that can result in serious injury or death.
c. Contact a qualied electrician or the manufacturer if there are questions about the installation prior
to connecting the equipment.
d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate
short-circuit backup protection.
e. Protective bonding must be installed in accordance with local national wiring rules and regulations.
ES-5XP Quick Start Guide