Ubiquiti UA-Hub User manual

11/6/2020 UA-Hub Quick Start Guide
https://dl.ubnt.com/qsg/UA-Hub/UA-Hub_EN.html 1/16
UA-Hub DIN Rail Self-Tapping Screws
(Qty. 2)
Screw Anchors
(Qty. 2)
Package Contents
Note: Each UniFi Access component and all third-party accessories are sold
separately.
Installation Requirements
Phillips screwdriver
Ethernet cables, CAT5e or better
Copper wire, 18 AWG to 22 AWG
Drill Kit
DIN Rail
Wire Ferrule Terminal (Recommended)
Sample Wiring Topology
UA-Hub Quick Start Guide

11/6/2020 UA-Hub Quick Start Guide
https://dl.ubnt.com/qsg/UA-Hub/UA-Hub_EN.html 2/16
Door Position Switch
Externally Powered Door Opener
Magnetic Lock
Hardware Overview
UA-Hub Quick Start Guide

11/6/2020 UA-Hub Quick Start Guide
https://dl.ubnt.com/qsg/UA-Hub/UA-Hub_EN.html 3/16
Power (In) LED
PoE (Out) LEDs
12V Line Output LED
12V Line Output Relays
Steady Blue Adopted/device is ready
Steady White Pending adoption
Alternating White/Blue Upgrading firmware
Off Not connected or no data link
Steady Blue Connected and data link on
Off Not connected
Steady Blue Effectively connected*
UA-Hub Quick Start Guide

11/6/2020 UA-Hub Quick Start Guide
https://dl.ubnt.com/qsg/UA-Hub/UA-Hub_EN.html 4/16
Input Relays
Input Relay LEDs
Output Relays
Output Relay LEDs
Line voltage with 12VDC power
REN Request to enter
REX Request to exit
DPS Door position switch
REL Remote release
Off Not connected
Steady Blue Effectively connected*
DRY Output relay with no power
POWERED Output relay with 12VDC
Off Not connected
Steady Blue Effectively connected*
* Wires are properly connected to both relays in any of the following sets:
+/-
NC/COM
NO/COM
Default I/O State Matrix
LOCK
Dry
NO COM NC
Door Locked
Initial State
Opened Shorted Shorted
Unlocked
REN, REX, or REL is shorted; or the reader has
granted access
Shorted Shorted Opened
UA-Hub Quick Start Guide

11/6/2020 UA-Hub Quick Start Guide
https://dl.ubnt.com/qsg/UA-Hub/UA-Hub_EN.html 5/16
LOCK
Powered
NO COM NC
Door Locked
Initial State
0V GND +12V
Unlocked
REN, REX, or REL is shorted; or the reader has
granted access
+12V GND 0V
AUX
Dry
NO COM NC
Door Locked
Initial State
Opened Shorted Shorted
Unlocked
REN, REX, or REL is shorted; or the reader has
granted access
Shorted Shorted Opened
Powered
NO COM NC
Door Opened
DPS is opened
+12V GND 0V
Door Closed
DPS is closed
0V GND +12V
Example 1: Recommended Setup - Connect AUX DRY to automatic door opener with external
power
Example 2: Recommended Setup - Connect AUX POWERED to siren (12V / 0.33A / 4W) for
door position warning
Note: Specific behaviors can be further configured in UniFi Access Controller.
UA-Hub Wiring
Connecting the UA-Hub to LAN
Ensure the switch port that is connected to the UA-Hub is on the same LAN segment
or VLAN as the UniFi Access agent. It must also support PoE+ or PoE++.
Connecting the UA-Pro to the UA-Hub
1
2
1
2
UA-Hub Quick Start Guide

11/6/2020 UA-Hub Quick Start Guide
https://dl.ubnt.com/qsg/UA-Hub/UA-Hub_EN.html 6/16
Use an Ethernet cable to connect the UA-Pro access reader to the UA-Pro PoE port
on the UA-Hub.
Connecting the UA-Lite to the UA-Hub
Use an Ethernet cable to connect the UA-Lite access reader to the UA-Lite PoE port
on the UA-Hub.
Connecting the G3-Flex to the UA-Hub
Use an Ethernet cable to connect the G3-Flex camera to the G3-Flex PoE port on
the UA-Hub.
Connecting a Fail-Safe Lock with No External Power Supply
1. Connect the Lock Powered (NC) port on the UA-Hub to the (+) on the lock.
2. Connect the Lock Powered (COM) port on the UA-Hub to the (-) on the lock.
Fail-safe lock in this diagram refers to magnetic lock or electric bolt.
Connecting a Fail-Safe Lock with an External Power Supply
1. Connect the Lock DRY (NC) port on the UA-Hub to the (+) on the lock.
2. Connect the (-) on the lock to the (-) on the external power supply.
3. Connect the Lock DRY (COM) port on the UA-Hub to the (+) on the external
power supply.
UA-Hub Quick Start Guide

11/6/2020 UA-Hub Quick Start Guide
https://dl.ubnt.com/qsg/UA-Hub/UA-Hub_EN.html 7/16
Connecting a Push Button
1. Connect NO on the push button to REL (+) on the UA-Hub.
2. Connect COM on the push button to REL (-) on the UA-Hub.
Note: REL, REX, and REN all work the same way with push buttons.
Connecting a Motion Sensor
UA-Hub Quick Start Guide

11/6/2020 UA-Hub Quick Start Guide
https://dl.ubnt.com/qsg/UA-Hub/UA-Hub_EN.html 8/16
1. Connect NO on the motion sensor to REX (+) on the UA-Hub.
2. Connect COM on the motion sensor to REX (-) on the UA-Hub.
3. Connect V+ on the motion sensor to Line 12V (+) on the UA-Hub.
4. Connect V- on the motion sensor to Line 12V (-) on the UA-Hub.
Note: REL, REX, and REN all work the same way with motion sensors.
Connecting a Siren
1. Connect AUX Powered (NO) on the UA-Hub to the (+) on the siren.
2. Connect AUX Powered (COM) on the UA-Hub to the (-) on the siren.
Note: AUX powered output is 12VDC up to 0.33A.
The diagram below is an example; please consult the manual for your specific siren.
UA-Hub Quick Start Guide

11/6/2020 UA-Hub Quick Start Guide
https://dl.ubnt.com/qsg/UA-Hub/UA-Hub_EN.html 9/16
Connecting a Door Position Switch (Door Sensor)
1. Connect NC on the door position switch to the DPS (+) on the UA-Hub.
2. Connect COM on the door position switch to the DPS (-) on the UA-Hub.
Connecting an Automatic Door Opener with an External Power Supply
UA-Hub Quick Start Guide

11/6/2020 UA-Hub Quick Start Guide
https://dl.ubnt.com/qsg/UA-Hub/UA-Hub_EN.html 10/16
Please consult the manual for your specific automatic door opener. Use the AUX
relays for the automatic door opener connection.
Connecting a Fail-Secure Lock with No External Power Supply
Connect the Lock Powered NO and COM ports on the UA-Hub to the NO and COM
ports on the fail-secure lock, respectively.
Fail-secure lock in this diagram refers to electric strike.
Connecting Wire to Terminal Block
1.
UA-Hub Quick Start Guide