Ultimate Support SECOND TIER PRO User manual

V-STAND®PRO / IQ-3000
SECOND TIER PRO
Manual
V-Stand Pro
IQ-3000

Page 2
STEP 1 – PREPARE
V-STAND® PRO OR IQ-3000
OR
Back End
Back End
End
Cap
Sleeve
Sleeve
STEP 1A
Identify the back end of
the support arm of the
V-Stand Pro.
STEP 1B
Slide the support arm
back to make room for
second tier assembly
by lifting it up at an
angle, then sliding
it down until fully
extended. Lay arm flat
onto collar.
STEP 1C
Using a flathead
screwdriver, carefully
detach end cap.
STEP 1A
Identify the back end of
the support arm of the
IQ-3000.
STEP 1B
Slide sleeve forward to
make room for second
tier pro assembly.
STEP 1C
Using a flathead
screwdriver, carefully
detach end cap.

Page 3
STEP 2 – ASSEMBLE
SUPPORT ARMS
Small Spring
Riser Tube
Nut
Z-knob
Washer
Support Arm
STEP 2A
Place nut (H) in well of riser tube (B) on opposite side
of teeth. (NOTE: Until assembled, may fall
out – do not lose!)
STEP 2B
Place one small spring (G) in the well at the center of
the teeth of both support arm (A) and riser tube (B).
Press and hold together.
STEP 2C
Place washer on z-knob (E). Assemble by screwing
z-knob (E) into Nut (H) through riser tube (B) and
support arm (A).
STEP 2D
Repeat STEPS 2A-2C for second assembly.
PARTS USED
A. Two (2) Support Arms
B. Two (2) Riser Tubes
E. Two (2) Z-knobs
F. Two (2) Washers
G. Two (2) Small Springs
H. Two (2) Nuts

Page 4
STEP 3B
Release the quick release lever. Slide end clamp onto end of
stand support arm. (NOTE: Make sure end clamp is as far onto
the support arm as possible.)
STEP 3C
Utilizing the leveling bubble, ensure end clamp is level. Secure
by flipping the quick release lever toward end clamp (which
can be tightened, or loosened using a flathead screwdriver).
STEP 3A
Loosen z-knob on end clamp and rotate until bubble level
and riser tube receiver are perpendicular.
STEP 3 – ATTACH CLAMPS AND
ARMS TO STAND
Z-Knob
Support Arm End Clamp
Quick Release Lever
Quick Release Lever
Flathead screwdriver
Riser Tube
Bubble Level

Page 5
STEP 3D
Using printed height markers, choose desired height and adjust
memory collar position to that line. Use included allen wrench
to lock in place. (NOTE: Leave slightly loose, as you will tighten
completely in STEP 3F.)
STEP 3E
Slide riser tub with memory clamp into end clamp receiver.
STEP 3F
Memory Collar will lock into place in end clamp receiver
groove. After ensuring desired height, make sure 1st tier and
2nd tier support arms are parallel. Finally, tighten completely
using included allen wrench.
Allen Wrench
Allen Wrench
Memory Collar
Memory Collar
Memory Collar
Riser tub
Riser tub
End Clamp
End Clamp
Receiver Grove
End Clamp Receiver

Page 6
STEP 4A – Adjust Level
Utilizing the leveling bubble, ensure end clamp is level. If desired,
arms can be adjusted to desired angle, in or out of center, by
loosening Z-knob, adjust to desired angle, then tighten.
STEP 4C – Adjust Angle
Adjust angle of support arm by loosening z-knob, adjust to
desired angle, then tighten.
STEP 4B – Set Height
Set and/or change height by installing memory collar at desired
height (use included allen wrench to tighten).
STEP 4 – Adjust Angles
and Height

Page 7
Included Parts:
A. Two (2) Support Arms
B. Two (2) Riser Tubes
C. Two (2) Memory Collar
D. Two (2) End Clamps
E. Two (2) Z-knobs
F. Two (2) Washers
G. Two (2) Small Springs
H. Two (2) Nuts
Included Tool:
I. One (1) Allen Wrench
Other Tool needed:
J. One (1) Flathead
Screwdriver
(Not Included)
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.

Visit ultimatesupport.com
to download a detailed
product manual, read full
warranty details and to
register for warranty.
800.525.5628 . www.ultimatesupport.com . Copyright 2018, Ultimate Support Systems . All Rights Reserved