Unfinished Furniture of Wilmington T-4464XB User manual

ITEM NO.: T-4464XB
ISSUED APR 17, 2019
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: 44X44X64 BUTTERFLY SEASIDE TABLE
: T-4464XB

ITEM NO.: T-4464XB
ISSUED APR 17, 2019
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish
of your table. Protect the surface of the table with cloth if you are using any product with
rubber feet or base.
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
B
Leg
4
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M8 x 50mm)
8
2
Lock Washer
(8.5 x13mm)
8
3
Flat Washer
(2 x 8.5 x19mm)
8
4
Allen Key
(M4 x 30mm x 110mm)
1
BEFORE ASSEMBLY

ITEM NO.: T-4464XB
ISSUED APR 17, 2019
Printed in Vietnam
- 3 -
Unlock the table top (A) from both sides underneath the top and pull the two parts of the table top apart.
Attach legs (B) to the top (A) with bolts (1), and washers (2) and (3) as shown below. Tighten with Allen key (4).
STEP 1

ITEM NO.: T-4464XB
ISSUED APR 17, 2019
Printed in Vietnam
- 4 -
STEP 2
Unlock the table top from both sides underneath the top as shown below.
Pull the two parts of the table top apart.

ITEM NO.: T-4464XB
ISSUED APR 17, 2019
Printed in Vietnam
- 5 -
STEP 3
Place the butterfly leaf in the center of the open table top, as shown below.
Note: The metal swivel bar bracket is very flexible and a slight twist of one half of the leaf can get the
leaf into alignment. With one of these tops opened and in the topside up position and can be
attached to the base to accomplish this too.
Have the top fully extended first, pull the leaf operation out, and with one leaf end down and other in
the upward position, grasp the sides of the leaf w/ two hands and twist slightly (the metal bracket is
flexible) so to shift the alignment of the leaf and then lower it into place being careful not to let the metal
pins hit the edges of top or the leaf apron end, but repeat if necessary so to get the pins to align.
We use the flexible metal bar for this purpose, as a hardened metal would snap during transport or
damage the under structure.
STEP 3

ITEM NO.: T-4464XB
ISSUED APR 17, 2019
Printed in Vietnam
- 6 -
STEP 4
Push the table top closed. Lock the mechanism underneath two sides of the table top as shown below.
STEP 3