Unfinished Furniture of Wilmington T-36SDP User manual

ITEM
NO
:
T
-
36SDP
REVISED
SEP 09
, 2014
Printed in Vietnam
- 1 -
Description
Item No.
: 36 X 36 SQUARE DROPLEAF PED TABLE
: T-36SDP
ASSEMBLY INSTRUCTIONS

ITEM
NO
:
T
-
36SDP
REVISED
SEP 09
, 2014
Printed in Vietnam
- 2 -
BEFORE ASSEMB
LY
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
-Remove all wrapping material, including staples & packing straps before you start to assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish of your
table. Protect the surface of the table with cloth if you are using any product with rubber feet or base.
PART
LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO Description Qty Sketch NO Description Qty Sketch
A Top 1 B Leg 4
C Pedestal 1 D Mounting
Plate 1
E Wood slide 2

ITEM
NO
:
T
-
36SDP
REVISED
SEP 09
, 2014
Printed in Vietnam
- 3 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1 Large Flat Washer
( 8.5x19mm) 4
2 Large Lock Washer
(8.5x13mm) 4
3 Hexagon Nut
(M8 x13mm) 4
4 Wrench
(13mm) 1
5 Small Flat Washer
( 6.5x13mm) 4
6 Small Lock Washer
( 6.5x11mm) 12
7 Medium Flat Washer
( 6.5x19mm) 8
8 Bolt
(M6x45mm) 12
9 Allen Key
(M4 x 80mm) 1
STEP 1
Attach Legs (B) to pedestal (C) with Nuts (3), and Washers (2) and (1). Tighten with the Wrench (4) as
shown below.

ITEM
NO
:
T
-
36SDP
REVISED
SEP 09
, 2014
Printed in Vietnam
- 4 -
STEP 2
Attach the mouting plate (D) on top of the pedestal (C) with washers (5) and (6), and bolts (8), as
shown below. Tighten with the Allen key (9).
Insert the wood slides (E) into the groove of the mouting plate.
STEP 3
Carefully place the pedestal on the bottom side of the table top. Attach the top (A) to mounting
plate with bolts (8), and washers (6) and (7). Tighten with the Allen key (9)

ITEM
NO
:
T
-
36SDP
REVISED
SEP 09
, 2014
Printed in Vietnam
- 5 -
STEP 4
Hold the dropleaf push and slide the wooden piece from underneath the table top . To lower the
dropleaf, carefully hold the dropleaf with one hand and slide the wooden piece from underneath
the table top towards the center of the top. Then, gently lower the leaf and place in the down
position.