UNITED OFFICE ULGD 350 A1 User manual

IAN 100158
LAMINATOR ULGD 350 A1
LAMINATOR
Operating instructions
NAPRAVA ZA PLASTIFICIRANJE
Navodila za uporabo
LAMINÁLÓGÉP
Használati utasítás
URZĄDZENIE DO LAMINOWANIA
Instrukcja obsługi
PRÍSTROJ NA LAMINOVANIE
Návod na obsluhu
LAMINOVAČKA
Návod k obsluze
LAMINIERGERÄT
Bedienungsanleitung

GB Operating instructions Page 1
PL Instrukcja obsługi Strona 15
HU Használati utasítás Oldal 29
SI Navodila za uporabo Stran 43
CZ Návod k obsluze Strana 57
SK Návod na obsluhu Strana 71
DE/AT/CH Bedienungsanleitung Seite 85
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi
funkcjami urządzenia.
Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik
funkcióját.
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.

1
2
3
5
6
7
4

1
ULGD 350 A1
GB
Index
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Information for these operating instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Limited liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warning symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Basic Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setting up and connecting to the power supply . . . . . . . . . . . . . . . . . . . . . 5
Items supplied and transport inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Disposal of the packaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Requirements on the installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Appliance description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Handling and operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Suitable laminating pouches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Switching levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Preparing for hot lamination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Preparing for cold lamination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Lamination process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Anti-blocking function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Notes on the Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Importer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
IB_100158_ULGD350A1_LB4.indb 1 02.07.14 13:42

2ULGD 350 A1
GB Introduction
Information for these operating instructions
Congratulations on the purchase of your new appliance.
You have clearly decided in favour of a quality product. These operating instructions
are a component of the Laminator ULGD 350 A1 (henceforth designated as the
appliance) and they supply you with important information on the intended use,
safety, installation and connection as well as operation of the appliance.
These operating instructions must be constantly kept available close to the appli-
ance. They are to be read and applied by everyone occupied with operating the
appliance and eliminating any malfunctions it may have.
Retain these operating instructions and pass them on, with the appliance, to any
future owners.
Copyright
This documentation is copyright protected.
All reproductions or duplications, also as extracts, as well as representations
of the illustrations, even in an altered state, are only permitted with the written
approval of the manufacturer.
Limited liability
All technical information, data and instructions for installation, connection and
operation contained in this operating manual correspond to the latest available
at the time of printing and, to the best of our knowledge, take into account our
previous experience and know-how.
No claims can be derived from the details, illustrations and descriptions in these
instructions.
The manufacturer assumes no responsibility for damage caused by failure to observe
these instructions, improper use, incompetent repairs, making unauthorised modi-
fications or for using unapproved replacement parts.
Intended use
This laminator is intended exclusively for use in domestic households, for the hot
and cold lamination of documents made from paper or cardboard. This appliance
is not intended for commercial or industrial use.
This appliance is not intended for any other use or for uses beyond those men-
tioned. Claims of any kind for damage resulting from unintended use will not
be accepted. The user alone bears liability.
IB_100158_ULGD350A1_LB4.indb 2 02.07.14 13:42

3
ULGD 350 A1
GB
Warning symbols used
In these operating instructions the following warnings are used:
DANGER
A warning at this risk level indicates a threateningly dangerous
situation.
If the dangerous situation is not avoided, it could result in death or serious injury.
► Follow the instructions given in this warning to avoid the risk of death or
severe personal injury.
WARNING
A warning at this risk level indicates a possible dangerous
situation.
If the dangerous situation is not avoided it could lead to injuries.
► Follow the instructions given in this warning to avoid the risk of personal
injuries.
IMPORTANT
A warning at this risk level indicates possible property damage.
If the situation is not avoided it could lead to property damage.
► Follow the instructions in this warning to avoid property damage.
NOTICE
► A notice indicates additional information that may assist you in the handling
of the appliance.
IB_100158_ULGD350A1_LB4.indb 3 02.07.14 13:42

4ULGD 350 A1
GB Safety
In this chapter you receive important safety information regarding the handling
of the appliance. This appliance complies with the statutory safety regulations.
Incorrect usage can lead to personal injury and property damage.
Basic Safety Instructions
For safe handling of the appliance observe the following
safety information:
■ Before use check the appliance for visible external dam-
age. Do not put into operation an appliance that is dam-
aged. There will be a risk of a fatal electrical shock.
■ Repairs should only be carried out by authorised special-
ist companies or by the Customer Services department.
Incorrect repairs can result in significant risks for the user.
In addition, warranty claims become void.
■ To avoid risks, arrange for a defective power cable to be
replaced by qualified technicians or by our Customer
Service Department.
■ NEVER use the appliance with a defective power cable.
There will be a risk of a fatal electrical shock.
■ Do not use extension cables or power socket strips that
do not meet the required safety standards.
■ The mains power socket must be easily accessible, so that
the power cable can be easily and quickly disconnected
in the event of an emergency.
■ Do not use an external timing switch or a separate re-
mote control system to operate the appliance.
■ This appliance may be used by children aged 8 over
and by persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge, pro-
vided that they are under supervision or have been told
how to use of the appliance safely and are aware of the
potential risks. Children must not play with the appliance.
Cleaning and user maintenance tasks must not be carried
out by children unless they are supervised.
IB_100158_ULGD350A1_LB4.indb 4 02.07.14 13:42

5
ULGD 350 A1
GB
■ Never perform hot lamination on flammable, heat-
sensitive and/or meltable materials and do not laminate
drawings on temperature-sensitive paper or material that
will undergo changes in colour or quality when subjected
to heat.
■ Never laminate valuable or unique documents. Although
the appliance complies with all current safety norms/
standards, malfunctions can never be completely ruled
out. Malfunctions with the laminator can result in damage
to the document being laminated.
Setting up and connecting to the power supply
Items supplied and transport inspection
The appliance is delivered with the following components as standard:
▯ Laminator ULGD 350 A1
▯ Document support
▯ 10 x Laminating pouches DIN A4 for hot laminating (80 micron)
▯ 10 x Laminating pouches DIN A5 for hot laminating (80 micron)
▯ 10 x Laminating pouches for hot lamination of business cards (80 micron)
▯ This operating manual
NOTICE
► Check the contents to make sure everything is present and for signs of visible
damage.
► If the contents are not complete or are damaged due to defective packaging
or through transportation, contact the Service Hotline (see chapter Service).
Unpacking
♦ Extract the appliance, the laminating pouches and the operating instructions
from the carton.
♦ Remove all packing material.
DANGER
► Packaging material should not be used as a play thing by children. There is
a risk of suffocation!
IB_100158_ULGD350A1_LB4.indb 5 02.07.14 13:42

6ULGD 350 A1
GB Disposal of the packaging
The packaging protects the appliance from transport damage. The packaging
materials are selected from the point of view of their environmental friendliness
and disposal technology and are therefore recyclable.
The recirculation of packaging into the material circuit saves on raw material and
reduces the amount of waste generated. Dispose of packaging material that is
no longer needed as per the regionally established regulations.
NOTICE
► If possible preserve the appliance's original packaging during the warranty
period so that, in the event of a warranty claim, you can package the appli-
ance ideally for its return.
Requirements on the installation site
For safe and flawless operation of the appliance, the installation site must comply
with the following requirements:
■ When setting it up, place the appliance on a firm, flat and horizontal surface.
■ Place the appliance so that at least 30 cm of space remains unoccupied
behind the laminator. Otherwise the laminating pouch cannot be completely
ejected from the laminator after lamination.
■ Do not operate the appliance in a hot, wet or very humid environment or
close to combustible material.
■ The mains power socket must be easily accessible, so that the power cable
can be easily disconnected in the event of an emergency.
Electrical connection
IMPORTANT
► Before you connect the appliance, compare the connection data (voltage
and frequency) on the data plate with that of your mains power network.
This data must match in order to avoid any damage to the appliance.
► Ensure that the power cable is undamaged and is not routed over hot
surfaces and/or sharp edges.
► Ensure that the power cable is not taut or kinked.
► Do not let the power cable hang over edges (trip wire effect).
♦ Insert the plug into a mains power socket.
IB_100158_ULGD350A1_LB4.indb 6 02.07.14 13:42

7
ULGD 350 A1
GB
Appliance description
Pouch ejector slot
2Indicator light Ready (ready for use)
3Indicator light Power (appliance switched on)
4Anti-Blocking switch and pouch thickness switch
5On/Off switch with selector switch for hot and cold lamination (Hot/Off/Cold)
6Pouch slot for manual pouch insertion
Document support
Handling and operation
In this chapter you will receive important information about the handling and
operation of the appliance.
Suitable laminating pouches
For hot lamination you can use pouches with a width of up to 230 mm and a
maximum thickness of 125 micron. For cold lamination you can use pouches with
a maximum thickness of 200 microns. Please note that each laminating pouch
may only be used once.
NOTICE
► For hot lamination, use only laminating pouches that are expressly
intended for hot lamination.
► For cold lamination, use only laminating pouches that are expressly
intended for cold lamination.
► Take note that the laminating pouches supplied with the laminator are
intended exclusively for hot lamination.
Switching levels
Selector switch
position 5
Pouch thickness
switch position 4
Laminating pouch
thickness
Hot 80 > 60 - 80
Hot 125 85 - 125
Cold 125 to 200
NOTICE
► For high-gloss photos, you should select the switch position “125” as well
as the appropriate pouch thickness.
IB_100158_ULGD350A1_LB4.indb 7 02.07.14 13:42

8ULGD 350 A1
GB Preparing for hot lamination
♦ Insert the document support into the two openings under the pouch ejector
slot , such that it is seated firmly on the appliance.
♦ Insert the plug of the laminator into a mains power socket.
♦ Switch the appliance on by placing the selector switch for hot and cold
lamination 5at "HOT". The red indicator light Power 3glows.
♦ Place the pouch thickness switch 4at the corresponding pouch thickness
(see also chapter Switching levels).
NOTICE
► The attainment of the operating temperature is indicated by the glowing
of the green indicator light Ready 2. For a more uniform laminating result
we recommend, especially for thinner foils (below 125 Micron), and after
adjustment to a different foil thickness, to first wait an additional 2-3 minutes
before beginning with lamination.
♦ Place the document to be laminated into a laminating pouch of the
appropriate size.
NOTICE
► Ensure that all edges of the document have at least two millimetres of
space to the edges of the laminating pouch, as shown in Fig. 1.
► Ensure that you use only one pouch for laminating. First open it up, as
shown in Fig. 2.
► For further information about the lamination process, please read the
section Lamination process.
Fig. 1
Fig. 2
IB_100158_ULGD350A1_LB4.indb 8 02.07.14 13:42

9
ULGD 350 A1
GB
Preparing for cold lamination
IMPORTANT
► After hot laminating, allow the laminator to cool down completely before
beginning with cold lamination. Bear in mind, the rollers inside the laminator
will still be hot. This could damage the laminating pouch and the document
to be laminated!
♦ If not already done: Insert the document support into the two openings
under the pouch ejector slot , such that it is seated firmly on the appliance.
♦ Insert the plug of the laminator into a mains power socket.
♦ Switch the appliance on by placing the selector switch for hot and cold lami-
nation 5at "Cold". The red indicator light Power 3and the green indicator
light Ready 2glow.
♦ Place the pouch thickness switch 4at the corresponding pouch thickness
(see also chapter Switching levels).
♦ Place the document to be laminated into a laminating pouch of the appropriate
size.
NOTICE
► Ensure that all edges of the document have at least two millimetres of space
to the edges of the laminating pouch, as shown in Fig. 1 (see p. 8).
► Make certain that you use only one pouch for laminating. First open it up,
as shown in Fig. 2 (see p. 8).
► For further information about the lamination process, please read the section
Lamination process.
Lamination process
♦ Place the pouch centrally between the two A4 markings and with the closed
side towards the pouch slot 6and on the supporting surface.
♦ Slide the pouch slowly and straightly into the pouch slot 6.
♦ When you have slid the pouch several centimetres into the slot 6it will then
be pulled in automatically. Release the laminating pouch as soon as you
notice it being pulled in automatically.
IMPORTANT
► Ensure that there is at least 30 cm of free space behind the laminator.
Otherwise, the pouch will not be ejected completely from the laminator
after lamination. This could damage the pouch.
♦ The finished and laminated pouch is ejected from the pouch ejector slot
of the laminator.
IB_100158_ULGD350A1_LB4.indb 9 02.07.14 13:42

10 ULGD 350 A1
GB NOTICE
►Only after hot lamination: When the finished laminated pouch is
ejected from the pouch ejector slot of the laminator, it is hot and can
easily change its shape. For this reason, let the laminated pouch cool for
one minute before touching it.
► To improve the lamination result, you can weigh a still hot laminated pouch
down with a book, a file folder or any other heavy, flat object. This will
give it a smooth and flawless surface.
♦ If you do not wish to start another laminating procedure, move the On/
Off switch 5to "Off" and rotate the pouch thickness switch 4to the ABS
position.
♦ Disconnect the plug from the mains power socket.
Anti-blocking function
At the start of the lamination process, the pouch may be pulled in at an angle or
jam itself inside the appliance.
♦ Turn the anti-blocking switch 4to the position ABS. The pouch will no longer
be drawn in.
♦ Remove the pouch and turn the anti-blocking switch 4back to the desired
pouch thickness.
♦ Re-start the lamination process.
Cleaning
DANGER
Risk of potentially fatal electrical shock!
► Remove the plug from the mains power socket before beginning to clean
the appliance.
► Ensure that moisture cannot permeate into the appliance during cleaning.
IMPORTANT
Possible damage to the appliance.
► Do not use aggressive or abrasive cleaners as they may damage the surface
of the housing.
♦ Clean the housing of the appliance only with a lightly moistened cloth and
a mild detergent.
IB_100158_ULGD350A1_LB4.indb 10 02.07.14 13:42

11
ULGD 350 A1
GB
Cleaning the inside of the appliance:
With every lamination, contaminants are deposited on the rollers inside the
laminator. Over time, this reduces the performance of the laminator.
You should therefore clean the rollers inside the laminator after use.
♦ Prepare the appliance for use, as described in the chapter Preparing for
hot lamination, until the green indicator light Ready 2glows.
♦ Then guide a sheet of folded in the middle A4 paper (maximum thickness
1.0 mm), without a pouch and with the fold forward, slowly into the manual
pouch insertion slot 6.
♦ Release the sheet as soon as you notice that it is being pulled in automatically.
The contaminants on the rollers inside the laminator now firmly attach themselves
to the sheet of paper. The paper will be ejected from the pouch ejector slot
of the laminator.
♦ Repeat this cleaning process several times. Use a fresh clean sheet of paper
each time.
When you no longer see any contaminants on the paper, the rollers inside the
laminator are clean.
Storage
The appliance has a built-in cable winder on the underside of the housing, on
which you can wrap the power cable when it is not in use. This prevents the
power cable from being pinched, damaged or soiled, and it cannot become
a source of danger by hanging loosely down.
♦ Store the appliance in a clean, dry place away from direct sunlight.
Disposal
Do not dispose of the appliance into the normal household
waste. This product is subject to the provisions of the European
Directive 2012/19/EU WEEE (Waste Electrical and Electronic
Equipment).
Dispose of the appliance through an approved disposal centre or at your com-
munity waste facility. Pay heed to the currently applicable regulations. In case of
doubt, please contact your waste disposal centre.
IB_100158_ULGD350A1_LB4.indb 11 02.07.14 13:42

12 ULGD 350 A1
GB Appendix
Technical data
Operational voltage 220-240 V ∼, 50 Hz
Current consumption 1.6 A
Power consumption 350 W
Protection class II/
Pouch width max. 230 mm
Pouch thickness for hot lamination max. 125 Micron
Pouch thickness for cold lamination max. 200 Micron
Lamination times
Sheet size Pouch thickness switch
position: 80 Micron
Pouch thickness switch
position: 125 Micron
DIN A4 approx. 40 s approx. 51 s
DIN A5 approx. 29 s approx. 36 s
Overheating protection
This appliance is fitted with an overheating protector. If the motor overheats
due to overloading, the appliance switches itself off automatically. In this case,
disconnect the power cable and wait until the appliance has cooled down to
room temperature. You can then reconnect the power cable with a mains power
socket and take the appliance back into operation. We recommend that you let
the appliance cool down for about 30 minutes after 2 hours of operation.
Notes on the Declaration of Conformity
This appliance complies, in regards to conformance with
the basic requirements and other relevent regulations, with
the EMC Directive 2004/108/EC, as well as the Directive
for Low Voltage Devices 2006/95/EC.
The complete original Declaration of Conformity can be
obtained from the importer.
IB_100158_ULGD350A1_LB4.indb 12 02.07.14 13:42

13
ULGD 350 A1
GB
Warranty
The warranty for this appliance is for 3 years from the date of purchase. The
appliance has been manufactured with care and meticulously examined before
delivery.
Please retain your receipt as proof of purchase. In the case of a warranty claim,
please make contact by telephone with our Customer Service Department. Only
in this way can a post-free despatch for your goods be assured.
NOTICE
► The warranty covers only claims for material and manufacturing defects,
but not for transport damage, wearing parts or for damage to fragile com-
ponents, e.g. buttons or batteries.
This product is for domestic use only and is not intended for commercial use. The
warranty is void in the case of abusive and improper handling, use of force and
internal tampering not carried out by our authorised service branch.
Your statutory rights are not restricted in any way by this warranty. The warranty
period is not extended by repairs made under the warranty. This applies also to
replaced and repaired parts.
Damages and defects extant at the time of purchase must be reported immedi-
ately after unpacking, resp. no later than two days after the date of purchase.
Repairs made after the lapse of the warranty period are subject to charge.
Service
Service Great Britain
Tel.: [phone] (£ 0.10/Min.)
E-Mail: k[email protected]
IAN 100158
Hotline availability: Monday to Friday 08:00 - 20:00 (CET)
Importer
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM, GERMANY
www.kompernass.com
IB_100158_ULGD350A1_LB4.indb 13 02.07.14 13:42

14 ULGD 350 A1
IB_100158_ULGD350A1_LB4.indb 14 02.07.14 13:42

15
ULGD 350 A1
PL
Spis treści
Wprowadzenie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Informacje o niniejszej instrukcji obsługi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Prawo autorskie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Ograniczenie odpowiedzialności . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Użytkowanie zgodne z przeznaczeniem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Zastosowane wskazówki ostrzegawcze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Bezpieczeństwo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Podstawowe zasady bezpieczeństwa. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Ustawianie i podłączanie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Zakres dostawy i przegląd po rozpakowaniu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Rozpakowanie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Utylizacja opakowania . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Wymagania dotyczące miejsca ustawienia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Podłączenie elektryczne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Opis urządzania . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Obsługa i praca . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Odpowiednie folie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Stopnie przełączania. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Przygotowanie do laminowania na gorąco . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Przygotowanie do laminowania na zimno . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Laminowanie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Funkcja zapobiegająca blokowaniu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Czyszczenie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Przechowywanie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Utylizacja. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Załącznik. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Dane techniczne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Wskazówki dotyczące deklaracji zgodności . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Gwarancja. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Serwis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
IB_100158_ULGD350A1_LB4.indb 15 02.07.14 13:42

16 ULGD 350 A1
PL
Wprowadzenie
Informacje o niniejszej instrukcji obsługi
Gratulujemy zakupu naszego urządzenia.
Wybrany produkt charakteryzuje się wysoką jakością. Niniejsza instrukcja obsługi
stanowi część laminatora ULGD 350 A1 (nazywanego dalej „urządzeniem”)
i przekazuje ważne wskazówki dotyczące użytkowania zgodnego z przezna-
czeniem, bezpieczeństwa, montażu i podłączania, a także obsługi urządzenia.
Instrukcję obsługi należy zawsze przechowywać w pobliżu urządzenia. Musi ją
przeczytać, a także jej przestrzegać każdy, kto podejmuje się obsługi urządzenia
i usuwania usterek w urządzeniu.
Zachowaj tę instrukcję obsługi, a przy odsprzedaży urządzenia przekaż ją wraz
z urządzeniem nowemu właścicielowi.
Prawo autorskie
Niniejsza dokumentacja jest chroniona prawem autorskim.
Wszelkie rozpowszechnianie, wzgl. każdy przedruk, także we fragmentach,
jak również odtwarzanie ilustracji, także w zmienionym stanie, jest dozwolone
wyłącznie za pisemną zgodą producenta.
Ograniczenie odpowiedzialności
Wszystkie zawarte w niniejszej instrukcji obsługi informacje techniczne, dane,
wskazówki montażu i podłączania oraz obsługi, są aktualne na dzień prze-
kazania do druku i uwzględniają nasze dotychczasowe doświadczenie oraz
spostrzeżenia zgodnie z najlepszą wiedzą.
Na podstawie zawartych tu informacji, ilustracji i opisów nie można wysuwać
żadnych roszczeń.
Producent nie ponosi żadnej odpowiedzialności za szkody spowodowane nie-
przestrzeganiem instrukcji, użytkowaniem urządzenia niezgodnie z przeznacze-
niem, niefachowymi naprawami, niedozwolonymi przeróbkami ani używaniem
niedozwolonych części zamiennych.
Użytkowanie zgodne z przeznaczeniem
Urządzenie jest przeznaczone wyłącznie do laminowania na gorąco i na zimno
dokumentów z papieru i tektury w warunkach domowych. Urządzenie nie jest
przeznaczone do zastosowań przemysłowych ani profesjonalnych.
Inne lub wykraczające poza powyższe użytkowanie uznaje się za niezgodne
z przeznaczeniem. Wszelkie roszczenia z tytułu szkód wynikających z użytko-
wania niezgodnego z przeznaczeniem są wykluczone. Ryzyko ponosi wyłącznie
użytkownik.
IB_100158_ULGD350A1_LB4.indb 16 02.07.14 13:42

17
ULGD 350 A1
PL
Zastosowane wskazówki ostrzegawcze
W niniejszej instrukcji obsługi zastosowano następujące wskazówki ostrzegawcze:
NIEBEZPIECZEŃSTWO
Wskazówka ostrzegawcza tego stopnia zagrożenia oznacza
zagrażającą sytuację niebezpieczną.
Nieuniknięcie niebezpiecznej sytuacji może doprowadzić do śmierci lub
powstania ciężkich obrażeń.
► Należy przestrzegać instrukcji w niniejszej wskazówce ostrzegawczej,
aby uniknąć zagrożenia śmiercią lub ciężkich obrażeń ciała.
OSTRZEŻENIE
Wskazówka ostrzegawcza tego stopnia zagrożenia oznacza
możliwą sytuację niebezpieczną.
Nieuniknięcie niebezpiecznej sytuacji może doprowadzić do powstania
obrażeń.
► Należy przestrzegać instrukcji zawartych w niniejszej wskazówce
ostrzegawczej, by uniknąć obrażeń u osób.
UWAGA
Wskazówka ostrzegawcza tego stopnia zagrożenia oznacza
możliwą szkodę materialną.
Nieuniknięcie takiej sytuacji może doprowadzić do powstania szkód materialnych.
► Należy przestrzegać instrukcji zawartych w niniejszej wskazówce
ostrzegawczej, by uniknąć szkód materialnych.
WSKAZÓWKA
► Wskazówka oznacza dodatkowe informacje, ułatwiające korzystanie
z urządzenia.
IB_100158_ULGD350A1_LB4.indb 17 02.07.14 13:42