UNITED MICA UHM-852 User manual

USER’S MANUAL
for
MICA HEATERS
UHM-839 / UHM-852
Please read this instruction manual carefully before operation! Keep in a safe place
for future reference.

Ⅰ. Product Appearance
Ⅱ. Main Technical Date
Model
Rated Voltage
Rated Frequency
Rated Power
UHM-839
220-240V
50Hz
2000W
UHM-852
220-240V
50Hz
2000W
Ⅲ.Precaution Items For Safe Use
1) Please read the product manual carefully before using the heater.
2) Insert the plug into the socket(requirements for socket and power cord: AC
220-240V, 50/60Hz,≥10A).The heater must not be located below a fixed socket.
3) Please operate according to the instructions of the manual. Any unrecompensed
operation can cause fire, short circuit and personal injuries.
4) Unauthorized extension of power cord is not allowed to avoid fire caused by
overheating of the extension part.
5) In order to prevent short circuit, fire or damages to the appliance, never insert any
article into the heater or block the cooling net.
6) Since the heater can generate heat, don not touch the hot surface with uncovered
human body to prevent burns. Grab the plastic handle at the rear to move the heater
when necessary. In case that children, animals or lame people and people lacking
self-discipline are on the spot and left unattended, avoid using the appliance.
7) Never use the heater outdoors.

8) Do not use this heater in the immediate surroundings of a bath, a shower or a
swimming pool
9) Do not use the appliance in area where gasoline, paint and flammable liquid are
used to stored.
10) Never cover anything on the heater during use.
11) To avoid current overload, do not share the use of a single socket with other
appliances.
12) The heater must not be located below a fixed socket.
13) If the power cord is damaged, it must be replaced by the manufacturer or its
maintenance agent or a similarly qualified person in order to avoid potential hazards.
14) Never use the product with automatic power-on programmer, timer or other types
of installations.
15) In case of product failure, please contact after-sales service agent for inspection
and repairing. Unauthorized disassembling and replacement of parts are not allowed.
16) The product shall be packed properly to prevent it from dust and kept in a
well-ventilated, dry place.
CAUTION:
This appliance is not intended for use by persons (including children) whit reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Ⅳ . How to install
1.Free standing installation:
First, take the heater out the package and place it upside down on soft
surface. Second, take four screws from the accessories(two screw for
each castor, parallel the bevel of castor bracket to the bevel of the heater,
if installed reversely, the screw cannot be revolved in.)and aim them at
the taps to tighten them. Third, Then just upright the heater and put it
into use. You may refer to the following figure.

2.Wall mounting:
First, use an electric drill to drill four holes on the wall. Diameter and
depth for the drilling holes , you can find the distance between
the four holes .
Second, insert the plastic bulged screws into the drilling holes, then lat
the screws through the hooks and aim them at the holes, fix the hooks on
the wall. Aim two rubber pads on the back of heater with screws.
Third, find two holes locations on the handle at the rear of the heater and fix
them to the hooks on the wall. Pull the heater rightward to make the hooks
tally with the holes locations.
NOTE:
If wall mount method is adopted, installation of truckles is not allowed.
The mounting location shall be 15cm above the floor and 50cm beneath
the ceiling or more. You may refer to the following figure.

OPERATION
1) Room temperature can be adjusted using the thermostat. Simply turn the thermostat
knob clockwise, to increase the heater, and anti-clockwise to decrease the temperature,
until you reach the desired temperature.
2) Switch the heater to one of the following power settings.
Push switch one (I) for 1000W
Push switch two (II) for 2000W
3) The power switch lights up when activated.
4) Turning the thermostat control clockwise will increase the “set” temperature.
5) Turning the thermostat anti-clockwise will decrease the “set” temperature.
6) Do not cover the heater at any time during operation. There is a risk of fire if the
heater is covered.
7) Once you have finished using your heater, turn the power switches off, and the
thermostat control switch to the “Low” positions, and unplug from the mains supply.
Ⅵ .Circuit diagram

NOTICE ABOUT RECYCLING
Your product is designed and manufactured with high quality materials
and components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their
end-of-life, should be disposed of separately from your household
waste.
Please dispose of this equipment at your local community waste
collection/recycling centre. In the European Union there are separate collection
systems for used electrical and electronic products.
Please help us to conserve the environment we live in!
DECLARATION OFCONFORMITY
Herewith, Amiridis-Savvidis S.A. states that this product, complies with the
requirements of below directives:
EMC-Directive: 14 / 30 / EU
Low Voltage Directive: 14/ 35 / EU
CE Marking: 93 / 68 / EEC
RoHS Directive: 11 / 65 / EU
The detailed declaration of conformity can be found at www.united-electronics.gr
EXCLUSIVE IMPORTER IN GREECE:
Amiridis – Savidis S.A.
87A, 17th November Str - P.C. 55534
Pylaia - Thessaloniki - Greece
T: 2310944944 | F: 2310944940
www.amiridis-savvidis.gr
www.united-electronics.gr