UNITED UHR-832 User manual

Oil-Filled Radiator
INSTRUCTION MANUAL
MODEL UHR-832
DO NOT TURN HEATER UPSIDE-DOWN DURING OPERATION.

INTRODUCTION
Thank you for purchasing our Oil-Filled Radiator. Each unit has been
manufactured to ensure safety and reliability. Before first use, please
read the instructions carefully and keep them for further reference.
ASSEMBLY
Remove the heater and all the accessories from the carton.
1. Turn the heater upside down.
2. Position the wheel base assemblies between the end fins.
3.Attach them to the heater using the U-bolts and wing nuts supplied.
4. Tighten the wing nuts.
5. Turn the heater the right way up.
PARTS DESCRIPTION
1. Power switch
2. handle
3. LCD Display Screen
4. Oil filled fins
5. Castors
6. Power supply plug
7. Cord storage
8. MODE button
9. ℃/℉button
10.+ button
11.- button
12.Power button

OPERATION
This heater is equipped with ElectronicDigital Controls that provide the
ability to set the temperature to the exact degree desired .To operate ,
simply follow these instructions.
Electrical connection
1. Make sure that the appliance’s voltage and the line voltage match
2. Switch the power switch to 0.
3. Only connect the mains plug to a properly installed earthed socket
220-240V~,50Hz.
Connected Wattage
The power level of the device is 2500W
With this connected load a separate supply line protected by a 16A
household circuit breaker is recommended.
CAUTION overload:
1. If you use extension leads, these should have a cable cross-section of
at least 1.5m ㎡.
2. Do not use any multiple sockets, as this device is too powerful.
3. Do not connect other high power appliances to the same circuit.
Safety Switch:
Your radiator has a safety switch which turns off the electricity as soon
as the device falls over . The safety switch prevents dangerous
situations caused by overheating.
1. Always place the device in an upright position so that it is stable as
well as in order to prevent malfunctions.
2. The appliance may still remain hot after it has toppled over.
Wait until it has cooled down.

Switch the appliance on again using the button.
1. Switch on the appliance with the power switch.
2. Press the button
1 X for high power ( ).
2 X for medium power ( )
3 X for low power ( ),
4 X and the appliance goes to standby.
Note:the heater will run continuously if you do not set a
temperature.
SETTING THE TEMPERATURE
Note: you must set the thermostat in proper operation. After the
button is turned on, you must press the MODE setting, and then
accordingly:
1. Temperature setting: If ambient temperature increases
or decreases, you must press the MODE button and then
press "+" or "-" to set the required temperature.
Otherwise, the heater will not operate.
2. Switch the appliance on.
3. Press the button. The number “88”flashes on the
display.
4. Press the MODE button.The number 24℃or 75℉and a
thermometer symbol shall appear on the display. The
thermometer symbol flashes.
5. Use the ℃/℉button to select the temperature display in degrees
Celsius or in Fahrenheit.
6. Use the “+/-” buttons to set the desired room temperature. The
values can be read off the display.

Note:The radiator will now warm up the room. The thermometer
symbol flashes throughout.
When the desired temperature is reached, the thermometer symbol
stops flashing and is constantly lit.
The thermometer symbol flashes again as soon as the radiator
needs to be heated up again.
Use the” +/-“ buttons to change the desired room temperature at any
time.
SETTING THE TIMER (AUTO-OFF)
This function should only be set if you desire the heater to be
automatically shut off after a certain period of time (1 to 24
hours from the time the function is set)
1. Press the “MODE” button until the timer icon blinks. The hour
display will appear. The”AUTO OFF “icon will also appear.
2. Use the +and -buttons to set the heater operation time between 1
and 24 hours. This function will activate once the timer icon stops
blinking.
3. The heater will automatically turn-off when time runs out. (If the
heater has not been set with a specific time, from opening the
heater shall automatically turn off at the default time of 10 hours.)
SETTING THE TIMER (AUTO-ON)
This function provides a delayed start option and should only
be set if you desire that the heater is being automatically turned
ON after a certain period of time (1 to 24 hours from the time
the function is set).
1. Press the “MODE” button until the timer icon blinks. The hour display
will appear. The” AUTO ON” icon will also appear.

2. Use the + and - buttons to set the heater starting time between 1 and
24 hours. This function will activate once the timer icon stops
blinking.
3. The heater will automatically turn on when time expires.
4. The heater will automatically turn-on when time runs out. (If the
heater has not been set with a specific time, from opening the heater
shall automatically turn off at the default time which is 10 hours)
The ”AUTO OFF” and “AUTO ON” functions cannot be
combined at the same time
IMPORTANT SAFEGUARDS
1. Read the instructions carefully before usage and save them for future
reference.
2. Always disconnect the heater from the main supply when not in use
and when cleaning.
3. Do not leave the heater "ON" unattended.
4. Never cover the heater as this may lead to risk of fire.
5. Keep the heater a distance of at least 90 cm from any combustible
material, such as furniture, curtains, bedding cloths or papers.
6. Keep the heater clean. Do not allow objects to enter the ventilation, as
this may cause electric shock, fire or damage the heater.
7. Close supervision is required when any appliance is used near or by
children.
8. Never allow the cord to touch wet or hot surfaces, become twisted or
be within the reach of children.
9. Do not use outdoors.
10. Do not place on or near a hot gas or electric burner.
11. Never use the appliance with a damaged cord or plug or after the
appliance has malfunctioned or been damaged in any way.
12. Never attempt to open any part or dismantle the controls.
Responsibility for failure cannot be accepted if these instructions have
been ignored.
13. Do not use the appliance for anything other than its intended use.
14. This appliance is intended for household use only.
15. Regulations concerning the disposal of the oil when scraping the
appliance have to be followed.
16.Any repairs that need to be done to the heater must be referred to an
authorized service agent only.

17. If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent in order to avoid a hazard.
18. The heater must not be located immediately below a socket-outlet.
19. Do not use this heater in the immediate surroundings of a bath, a
shower or a swimming pool.
20. This heater is filled with a precise quantity of special oil. Repairs
requiring opening of the oil container are only to be made by the
manufacturer of his service agent who should be contacted if there is
an oil leakage. Regulations concerning the disposal of the oil when
scrapping the appliance have to be followed.
21. The appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person
responsible for their safety
22. Children should be supervised to ensure that they do not play with
the appliance.

NOTICEABOUT RECYCLING
Your product is designed and manufactured with high quality
materials and components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their
end-of-life, should be disposed of separately from your household
waste.
Please dispose of this equipment at your local community waste
collection/recycling centre. In the European Union there are separate collection
systems for used electrical and electronic products.
Please help us to conserve the environment we live in!
DECLARATION OF CONFORMITY
This product is in compliance with the standards of the below regulations:
EMC-Directive: 04 / 108 / EC
Low Voltage Directive: 06 / 95 / EC
RoHS2 Directive: 11 / 65 / EU
The above listed regulations declare that this product is in compliance with the following
norms::
EN 55014-1:06+A1:09+A2:11
EN 55014-2:97+A1:01+A2:08
EN 61000-3-2:06+A1:09+A2:09
EN 61000-3-3:13
EN 60335-2-30:09+A11:12
EN 60335-1:12
EN 62233:08
EN 62321:09
EXCLUSIVE IMPORTER IN GREECE:
Amiridis – Savidis S.A.
33, Vas. Olgas Street – P.C. 54641 – Thessaloniki, Greece.
Tel: [phone], Fax: [phone]
45 Posidonos St. – P.C. 18344 – Moschato,Athens, Greece
Tel: [phone], Fax: [phone]
www.united-electronics.gr