UPC 1455A User manual

ASSEMBLY INSTRUCTIONS
PARTS BAG UPC 1455A 14552 Icon 56 Pocket Spinner
PARTS LIST
Page 1 of 7
PART Quantity Reference
Push Pin 9(1 extra) A
Long Trusshead Screw 4 B
Connector Bolt 4 C
Short Trusshead Screw 4D
Hex Wrench 1E
Header Clip 1F
PART Quantity Reference
Top Cap 1G
Tower Panel 2H
Spinner Plate Assembly 1I
Base 1J
X-Base Lower 1K
X-Base Upper 1L
Racks 56 M
Tower Helper 2N
BCD
Revised 01/12/15
E
TOOLS REQUIRED: #2 Phillips Screwdriver
F
A
U.S. PATENT NO.
8,534,472
G
J
K
M
L
N
I
H
Finished Display

Page 2 of 7
ASSEMBLY
Insert X-Base Upper (L)
into X-Base Lower (K)
as shown below.
Attach Base (J) to
X-Base Assembly (K/L)
using (4) Connector Bolts (C).
2
1
C
J
L
K
U.S. PATENT NO.
8,534,472

ASSEMBLY
Page 3 of 7
Spin and align the large
holes in Spinner Plate
with Spinner.
3
4
Align large screw holes on
Spinner Plate Assembly (I) with
one of the four corresponding
holes on the X-Base Assembly.
Spinner Plate
Assembly (I)
(shown
exploded
for reference)
Spinner
Spinner
Plate
Spinner Plate
Assembly (I).
X-Base
Assembly
Hole 1
Hole 2
Hole 3
Hole 4
I
Bottom View of Spinner Plate Base (I).
Use Larger
Holes for
attachment
to X-Base.
I
Hole 2
Hole 3
Hole 1
Hole 1
Hole 2
Hole 3
U.S. PATENT NO.
8,534,472

ASSEMBLY
Page 4 of 7
Attach Spinner Plate
Assembly (I) to
X-Base Assembly
by using (1) Short
Trusshead Screw (D)
through large screw hole in
Spinner Plate (I) to hole in
X-Base Assembly.
DO NOT tighten
completely!
5
D
Repeat Step 6 for attaching
Spinner Plate Assembly (I) to
X-Base Assembly using
3rd & 4th Short Trusshead
Screws (D). Tighten all screws
7
STOP! If you are installing casters, please refer to
instruction sheet #14532 enclosed in your caster kit.
8STOP!
Turn Spinner Plate Assembly (I) 90º to
continue attachment to X-Base
Assembly, slight positioning
adjustment may be necessary to find hole.
To attach Spinner Plate (I), use 2nd
Short Trusshead Screw (D)
through large hole to corresponding hole
of X-Base Assembly.
6
3rd Short
Trusshead
Screw 4th Short
Trusshead
Screw
I
D
I
D
I
2nd Short
Trusshead
Screw
D
U.S. PATENT NO.
8,534,472

Small Hole
(align behind
Large Hole)
Facet with
Large Hole
(align in front
of Small Hole)
ASSEMBLY
A
9
H
Tower Panels (H)
MUST be aligned properly
at facets BEFORE securing
with Push Pins (A).
NOTE:
Page 5 of 7
Push Pins CANNOT be
removed once
inserted into holes!
A
A. Peel protective masking off
Tower Panels (H) before assembly.
B. Overlap each Tower Panel (H) so the large hole
of facet lies outside the small hole of
adjacent panel. (see figure RIGHT)
C. Use Large Finger Holes
(see figure RIGHT) to hold
Tower Panels (H) tightly
together while installing Push Pins (A).
D. Join (2) Tower Panels (H) together
using (8) Push Pins (A). (see figure BELOW)
(finger hole)
(finger
hole)
(finger
hole)
(finger
hole)
(finger
hole)
(finger
hole)
H
H
(finger hole)
close up view Top of
Tower Panel
(No Slot)
Bottom of
Tower Panel
(With Slot)
U.S. PATENT NO.
8,534,472