UPC Icon 72 Pocket Spinner 1453A User manual

ASSEMBLY INSTRUCTIONS
PARTS BAG UPC 1453A Icon 72 Pocket Spinner
PARTS LIST
Page 1 of 7
PART Quantity Reference
Push Pin 13 (1 extra) A
Long Trusshead Screw 6 B
Connector Bolt 4 C
Short Trusshead Screw 4D
Hex Wrench 1E
Header Clip 1F
PART Quantity Reference
Top Cap 1G
Tower Panel 3H
Spinner Plate Assembly 1I
Base 1J
X-Base Lower 1K
X-Base Upper 1L
Pockets 72 M
Tower Helper 2N
BCD
Revised 10/24/16
AE
TOOLS REQUIRED: #2 Phillips Screwdriver
F
G
U.S. PATENT NO.
8,534,472
H
I
J
K
M
L
N
Finished Display
Thank you for your purchase of one of many fine products designed & manufactured by UPC.
We have made every effort to make your assembly easy, clear & hassle free. For more information or
if you have any questions contact customer service at 1-800-859-7442.
upcdisplays.com
http://goo.gl/Z3AAcf
Watch the Instructional Video!

Page 2 of 7
ASSEMBLY
Insert X-Base Upper (L)
into X-Base Lower (K)
as shown below.
1
K
L
U.S. PATENT NO.
8,534,472
Attach Base (J)
to X-Base
Assembly (K/L) using
(4) Connector Bolts (C).
2
C
J
upcdisplays.com

ASSEMBLY
Page 3 of 7
Spin and align the large
holes in Spinner Plate
with Spinner.
3
4
Align large screw holes on
Spinner Plate Assembly (I) with
one of the four corresponding
holes on the X-Base Assembly.
Spinner Plate
Assembly (I)
(shown
exploded
for reference)
Spinner
Spinner
Plate
Spinner Plate
Assembly (I).
X-Base
Assembly
Hole 1
Hole 2
Hole 3
Hole 2
Hole 3
Hole 1
Hole 4
Bottom View of Spinner Plate Base (I).
Use Larger
Holes for
attachment
to X-Base.
I
I
Hole 1
Hole 2
Hole 3
U.S. PATENT NO.
8,534,472
upcdisplays.com

ASSEMBLY
Page 4 of 7
Attach Spinner Plate
Assembly (I) to
X-Base Assembly
by using (1) Short
Trusshead Screw (D)
through large screw hole in
Spinner Plate (I) to hole in
X-Base Assembly.
DO NOT tighten
completely!
5
D
I
Repeat Step 6 for attaching
Spinner Plate Assembly (I) to
X-Base Assembly using
3rd & 4th Short Trusshead
Screws (D). Tighten all screws
7
STOP! If you are installing casters, please refer to
instruction sheet #14532 enclosed in your caster kit.
8STOP!
Turn Spinner Plate Assembly (I) 90º to
continue attachment to X-Base
Assembly, slight positioning
adjustment may be necessary to find hole.
To attach Spinner Plate (I), use 2nd
Short Trusshead Screw (D)
through large hole to corresponding hole
of X-Base Assembly.
6
2nd Short
Trusshead
Screw
3rd Short
Trusshead
Screw
4th Short
Trusshead
Screw
D
I
D
I
D
I
U.S. PATENT NO.
8,534,472
upcdisplays.com

Small Hole
(align behind
Large Hole)
Facet with
Large Hole
(align in front
of Small Hole)
ASSEMBLY
Page 5 of 7
A
A. Peel protective masking off
Tower Panels (H) before assembly.
B. Overlap each Tower Panel (H) so the large hole
of facet lies outside the small hole of
adjacent panel. (see figure RIGHT)
C. Use Large Finger Holes (see figure RIGHT)
to hold Tower Panels (H) tightly
together while installing Push Pins (A).
D. Join (3) Tower Panels (H) together
using (12) Push Pins (A).
(see figure BELOW)
9
H
H
Tower Panels (H)
MUST be aligned properly
at facets BEFORE securing
with Push Pins (A).
NOTE:
Push Pins CANNOT be
removed once
inserted into holes!
(finger hole)
(finger hole)
(finger hole)
A
Top of
Tower Panel
(No Slot)
Bottom of
Tower Panel
(With Slot)
U.S. PATENT NO.
8,534,472
upcdisplays.com

H
B
Page 6 of 7
ASSEMBLY
This step will support Tower Panel
Assembly (H) up for installation to Base
Assembly. Insert (2) Tower Helpers (N)
in-between Spinner Plate Assembly (I) and
Base (J), as shown below.
10
HOLES
Align corresponding
holes and set the
Tower Panel
Assembly (H)
onto the
Base Assembly.
11
Continue to secure Tower Panel
Assembly (H) to Base Assembly at
corner holes of Tower Panel Assembly.
Attach panels to Spinner Plate edge with
(3) Long Trusshead Screws (B). Tighten
all (6) securely.
1312 Secure Tower Panel Assembly (H)
to Base Assembly at middle holes
of Tower Panel Assembly. Attach Tower Panels
to Spinner Plate edge with (3) Long Trusshead
Screws (B). DO NOT tighten completely!
N
H
B
H H
I
J
H
U.S. PATENT NO.
8,534,472
Base
Assembly
Base
Assembly
upcdisplays.com

Page 7 of 7
ASSEMBLY
Attach Pockets (M) by hooking the
tabs into the vertical slots in the
Tower Panels (H).
Lock bottom tongue of Pockets (M)
into the horizontal slots on
the Tower Panels (H).
Each vertical slot holds two
Pockets (M) side-by-side.
16
M
H
F
Peel masking off Header
Clip (F) and secure to the center
of the Top Cap (
G). Lower
Top Cap (G) on to the top
of the Tower Panel Assembly (H).
15
G
H
14
Remove Tower
Helpers (N).
N
U.S. PATENT NO.
8,534,472
upcdisplays.com