UPC HealthShield BarFly User manual

Page 1 of 5
Revised 05/28/20
H
H
I
I
I
J
A
A
B
B
CE
D
C
F
G
ASSEMBLY INSTRUCTIONS
#14096 / 14097 - BarFly
ASSEMBLY
Thank you for your purchase of one of many fine HealthSheild products designed & manufactured
by UPC. We have made every effort to make your assembly easy, clear & hassle free. For more
information or if you have any questions contact customer service at 1-800-859-7442.
upcdisplays.com
PART BAG Quantity Reference
Connector Bolt 6 A
Wing Nut 2 B
Washer 2 C
Rubber Washer 2 D
Allen Wrench 1 E
PART LIST Quantity Reference
BarFly Shield 1 F
Base 1 G
Large Extender Bracket 1 H
Small Extender Bracket 1 I
Foot 4 J
UPC HealthShield
TM
TM
D
1
Combining Large Extender Bracket (H) and Small Extender Bracket (I) is
determined by the thickness of the bar. This will determine where
Small Extender Bracket (I) is placed for this step.
If the thickness of the bar is less than 2” use Option 1.
If the thickness of the bar is greater than 2” use Option 2.
Attach Large Extender Bracket (H) to
Small Extender Bracket (I) with
(1) Connector Bolt (A),
(1) Rubber Washer (D)
(1) Washer (C) and
(1) Wing Nut (B).
Option 1
Option 2

Page 2 of 5
J
G
H
HI
B
G
ASSEMBLY
upcdisplays.com
2
3 Connect (2) Feet (J) to Base (G) with (2) Connector Bolts (A) using Allen Wrench (E). Make sure
(2) Feet (J) are aligned using BarFly Shield (F).
C
Attach Extender Assembly (H, I) to Base (G) using
(1) Connector Bolt (A), (1) Rubber Washer (D),
(1) Washer (C) and (1) Wing Nut (B).
Attach Base (G) to bar so that Base (G)
is closest to the patron and the
Extender Assembly (H,I) is
closest to the staff. Hook around
the bar, adjust
Extender Assembly (H, I)
accordingly.
A
A
D
I

Page 3 of 5
ASSEMBLY
upcdisplays.com
5
F
J
Adhesive Pads Protective
Strips
Peel the (2) Protective Strips from Adhesive Pads on (4) Feet (J).
6
Peel the Protective Paper from
both sides of the BarFly Shield (F).
Protective
Paper
4
Test fit the Assembly thus far to be sure that everything is fitting
correctly.
Note: Be careful to not make contact with
adhesive pads to any surface other than
intended location as adhesive is extremely
strong and bonds instantly.

Page 4 of 5
ASSEMBLY
upcdisplays.com
F
F
G
7
8
Overhang
Screw
Holes
Bar
NOTE: Make sure that overhang
of BarFly Shield (F) clears the front
of the bar.
Press the bottom of BarFly Shield (F)
into (2) Feet (J) to align. Then
press the top of BarFly Shield (F)
into Adhesive Pads on (2) Feet (J).
NOTE: Make sure Base (G) screw
holes align with screw holes on
(2) Feet (J).
Press Adhesive Pads of remaining
(2) Feet (J) against the BarFly Shield (F).
J
J

Page 5 of 5
ASSEMBLY
upcdisplays.com
F
9
To secure BarFly Shield (F) to Base (G) screw (2) Connector Bolts (A) into
remaning (2) Feet (J) using Allen Wrench (E).
A
JG