UPC 7290 User manual

ASSEMBLY INSTRUCTIONS
PARTS BAG UPC 7290 80 Pocket Spinner with Vacuum Formed Top
PARTS LIST
PART Quantity Reference
Push Pin 13 (1 extra) A
Long Trusshead Screw 6 B
Short Trusshead Screw 4 C
Connector Bolt 4 D
Hex Wrench 1E
Header Clip 1F
PART Quantity Reference
Top Cap 1G
Tower Panel 3-facet 2H
Tower Panel 4-facet 1I
Spinner Plate Assembly 1J
Base 1K
X-Base Lower 1L
X-Base Upper 1M
Racks 80 N
Tower Helper 2O
DC
E
TOOLS REQUIRED: #2 Phillips Screwdriver
B
E
G
F
J
K
L
M
O
N
A
Page 1 of 7
U.S. PATENT NO.
8,534,472
Revised 01/26/15
H
I
Finished Display

Insert X-Base Upper (M)
into X-Base Lower (L)
as shown below.
1
L
M
Attach Base (K)
to X-Base
Assembly (L/M) using
(4) Connector Bolts (D).
2
D
K
Page 2 of 7
U.S. PATENT NO.
8,534,472
L
M
ASSEMBLY
ASSEMBLY

Page 3 of 7
U.S. PATENT NO.
8,534,472
Hole 1
Hole 2
Hole 3
Spin & align the large
holes in Spinner Plate
and Spinner.
3
4
Align large screw holes on
Spinner Plate Assembly (J) with
one of the four corresponding
holes on the X-Base Assembly.
Spinner Plate
Assembly (J)
(shown
exploded
for reference)
Spinner
Plate
Spinner Plate
Assembly (J).
X-Base
Assembly
Hole 1
Hole 2
Hole 3
Hole 2
Hole 3
Hole 1
Hole 4
J
J
Bottom View of Spinner Plate Base (J).
Use Larger
Holes for
attachment
to
X-Base.
ASSEMBLY

Page 4 of 7
U.S. PATENT NO.
8,534,472
Attach Spinner Plate
Assembly (J) to
X-Base Assembly
by using (1) Short
Trusshead Screw (C)
through large screw hole in
Spinner Plate (J) to hole in
X-Base Assembly.
DO NOT tighten
completely!
5
C
J
Repeat Step 6 for attaching
Spinner Plate Assembly (J) to
X-Base Assembly using
3rd & 4th Short Trusshead
Screws (C). Tighten all screws
7
STOP! If you are installing casters, please refer to
instruction sheet #14532 enclosed in your caster kit.
8STOP!
Turn Spinner Plate Assembly (J) 90º to
continue attachment to X-Base
Assembly, slight positioning
adjustment may be necessary to find hole.
To attach Spinner Plate (J), use 2nd
Short Trusshead Screw (C)
through large hole to corresponding hole
of X-Base Assembly.
6
2nd Short
Trusshead
Screw
3rd Short
Trusshead
Screw
4th Short
Trusshead
Screw
C
J
C
J
C
J
ASSEMBLY

9
Small Hole
(align behind
Large Hole)
Facet with
Large Hole
(align in front
of Small Hole)
A
I
A. Peel protective masking off
(2) 3-facet Tower Panels (H),
and (1) 4-facet Tower Panel (I)
before assembly.
B. Overlap each Tower Panel (H, I) so the large hole
of facet lies outside the small hole of
adjacent panel. (see figure RIGHT)
C. Use Large Finger Holes (see figure RIGHT)
to hold Tower Panels (H, I) tightly
together while installing Push Pins (A).
D. Join (3) Tower Panels (H, I) together
using (12) Push Pins (A). (see figure BELOW)
H
Tower Panels (H) & (I)
MUST be aligned properly
at facets BEFORE securing
with Push Pins (A).
NOTE:
Push Pins CANNOT be
removed once
inserted into holes!
A
(finger
hole)
(finger
hole)
(finger
hole)
(finger
hole)
(finger
hole)
(finger
hole)
H
I
NOTE: No slot at
top of Tower Panel (H)
NOTE: Slot at
bottom of Tower Panel (H)
(finger hole)
close up view
H
Page 5 of 7
U.S. PATENT NO.
8,534,472
ASSEMBLY
ASSEMBLY

10
HOLES
Align corresponding
arrows and holes up then
set the Tower Panel
Assembly (H/I) onto the
Base Assembly.
11
Continue to secure Tower Panel
Assembly (H/I) to Base Assembly at
corner holes of Tower Panel Assembly.
Attach panels to Spinner Plate edge with
(3) Long Trusshead Screws (B) tighten
all (6) securely.
13
12 Secure Tower Panel Assembly (H/I)
to Base Assembly at middle holes
of Tower Panel Assembly. Attach Tower Panels
to Spinner Plate edge with (3) Long Trusshead
Screws (B). DO NOT tighten completely!
O
J
Page 6 of 7
U.S. PATENT NO.
8,534,472
This step will support Tower Panel
Assembly (H/I) up for installation to Base
Assembly. Insert (2) Tower Helpers (O)
in-between Spinner Plate Assembly (J) and
Base (K), as shown below.
Base
Assembly
Base
Assembly
K
H/I
B
Page 3 of 3
B
ASSEMBLY
H/I H/I

Attach Racks (N) by hooking the
tabs into the vertical slots in the
Tower Panel Assembly (H/I).
Lock bottom tongue of Racks (N)
into the horizontal slots on
the Tower Panel Assembly (H/I).
Each vertical slot holds two
Racks (N) side-by-side.
16
Peel masking off Header
Clip (F) and secure to the center
of the Top Cap (
G). Lower
Top Cap (G) on to the top
of the Tower Panel Assembly (H/I).
15
14
Remove Tower
Helpers (O).
G
Page 7 of 7
U.S. PATENT NO.
8,534,472
O
M
ASSEMBLY
F
H/I
H/I
H/I