Urban Electric ADGER’S WHARF Quick start guide

JG-1900
ADGER’S WHARF
ASSEMBLY AND MOUNTING INSTRUCTIONS
GENERAL NOTES
COMPONENTS PROVIDED FOR INSTALLATION
• THIS LUMINAIRE IS SUITED FOR WET LOCATIONS.
• THIS LUMINAIRE IS UL LISTED. WHEN INSTALLING LUMINAIRE, CONFORM
TO ALL APPLICABLE LOCAL ELECTRICAL CODES, ORDINANCES, AND THE
NATIONAL ELECTRICAL CODE (NEC).
• FOR YOUR SAFETY AND PROPER OPERATION OF LUMINAIRE, READ AND
UNDERSTAND ALL INSTRUCTIONS COMPLETELY BEFORE COMMENCING
INSTALLATION OF THIS LUMINAIRE.
• CAREFULLY UNPACK THE LUMINAIRE AND INSPECT FOR DAMAGE.
• THIS PRODUCT IS RATED ONE OR TWO 60W MAX, TYPE B BULB(S).
• SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CAUTION
THIS PRODUCT SHOULD BE INSTALLED ONLY BY A LICENSED ELECTRICIAN.
WARNING
THE ELECTRICITY MUST BE TURNED OFF AT THE MAIN FUSE BOX BEFORE
INSTALLING THIS LUMINAIRE. TURNING THE POWER OFF USING THE LIGHT
SWITCH MAY NOT BE SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
NIPPLE CAP WIRE NUTS CROSS BAR
CANDELABRA BULB(S)
SUNLIGHT- 25R14FL-MED
REFLECTOR FLOOD- INDOOR R14
25 WATT-120V
SUNLIGHT- CAT # 01910
CANDELABRA BASE-25T6/CL BULB
25 WATT-120V CLEAR
SUNLIGHT- CAT # 01929
CANDELABRA BASE-25T8/CL BULB
25 WATT-120V CLEAR
SUNLITE- 40CFC CAT# 01345
CANDELABRA-BASE FLAME TIP
40 WATT-120V CLEAR
SUNLIGHT- CAT # 01105
HOUSEHOLD CLEAR
60 WATT-120
60A/CL
SUNLIGHT- 60CTC CAT # 01395
CANDELABRA BASE-TORPEDO TIP
60 WATT-120V CLEAR
SUNLIGHT- CAT # 01216
SILVER BOWL-A-19/CLEAR BULB
100 WATT-120/130V GLARE FREE
100ASB-SU
FERROWATT
40 WATT-120V CLEAR
SUNLIGHT- CAT # 03470
MEDIUM BASE-MR16 BULB
50 WATT-120V HALOGEN
SUNLIGHT
COMPACT FLUORESCENT
13 WATT-120V
SL13SP65-SU
SUNLITE-COMPACT FLOURESCENT
SLC14TW/30K
14 WATT-(INCANDESCENT EQUIVALENT 60 WATT)
CAT # 65700 WARM WHITE
SUNLIGHT- CAT # 05510
COMPACT FLUORESCENT
25 WATT- INCANDESCENT EQUIVALENT-100 WATTS
SLS25/65K-BX
WESTINGHOUSE # 03840
WHITE 580 LUMENS
60 WATT-120V
WESTINGHOUSE-TUBULAR-25W
STANDARD BASE
25 WATT-120V
03835 25T10/F

ADGER’S WHARF
ASSEMBLY AND MOUNTING INSTRUCTIONS JG-1900
MOUNTING INSTRUCTIONS
MOUNTING DIAGRAM ELECTRICAL CONFIGURATION TABLE
FROM HOME FROM LUMINAIRE
CONNECT BLACK OR RED (HOT)
HOUSE SUPPLY CIRCUIT WIRE TO:
LUMINAIRE ROUND WIRE (HOT)
CONNECT WHITE (NEUTRAL)
HOUSE SUPPLY CIRCUIT WIRE TO:
LUMINAIRE RIBBED WIRE
(NEUTRAL)
CONNECT GREEN INSULATED OR BARE COPPER (GROUND -) HOUSE
SUPPLY CIRCUIT WIRE AND LUMINAIRE BARE STRANDED WIRE
(GROUND -) TO GREEN GROUND SCREW ON CROSSBAR.
GENERAL NOTE: USE UL LISTED WIRE NUTS FOR THE
WIRING CONNECTIONS IN THIS LUMINAIRE. WRAP WIRE NUT
CONNECTIONS WITH UL LISTED ELECTRICAL TAPE.
FOR QUESTIONS, PLEASE CONTACT CLIENT SERVICES AT:
843.723.8140 OR [email protected]
STEP 1
SHUT OFF THE MAIN ELECTRICAL SUPPLY TO THE JUNCTION
BOX FROM THE FUSE BOX/CIRCUIT BREAKER. TURNING
POWER OFF AT THE SWITCH IS NOT SUFFICIENT.
STEP 2
LOCATE JUNCTION BOX AND ATTACH CROSS-BAR PROVIDED TO
THE JUNCTION BOX.
STEP 3
USING THE WIRE NUTS PROVIDED, MAKE ELECTRICAL
CONNECTIONS BY FOLLOWING THE ELECTRICAL CONFIGURATION
TABLE BELOW. ENSURE THAT ALL ELECTRICAL CONNECTIONS ARE
WRAPPED WITH UL-LISTED ELECTRICAL TAPE.
STEP 4
ATTACH THE FIXTURE TO THE CROSS-BAR USING THE THREADED
NIPPLE AND CAP PROVIDED. BE CAREFUL TO AVOID SCRATCHING
THE FINISH ON THE FIXTURE.
STEP 5
INSTALL LIGHT BULB IN FIXTURE SOCKET AND RESTORE POWER
TO THE CIRCUIT.
STEP 6
CONFIRM PROPER OPERATION OF THE LIGHT FIXTURE.