Urban Electric BELMONT WALL Quick start guide

MM-3900
BELMONT WALL
ASSEMBLY AND MOUNTING INSTRUCTIONS
GENERAL NOTES
COMPONENTS PROVIDED FOR INSTALLATION
• THIS LUMINAIRE IS SUITED FOR WET LOCATIONS.
• THIS LUMINAIRE IS UL LISTED. WHEN INSTALLING LUMINAIRE, CONFORM
TO ALL APPLICABLE LOCAL ELECTRICAL CODES, ORDINANCES, AND THE
NATIONAL ELECTRICAL CODE (NEC).
• FOR YOUR SAFETY AND PROPER OPERATION OF LUMINAIRE, READ AND
UNDERSTAND ALL INSTRUCTIONS COMPLETELY BEFORE COMMENCING
INSTALLATION OF THIS LUMINAIRE.
• CAREFULLY UNPACK THE LUMINAIRE AND INSPECT FOR DAMAGE.
• THIS PRODUCT IS RATED ONE 60W MAX, TYPE B BULB(S).
• SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CAUTION
THIS PRODUCT SHOULD BE INSTALLED ONLY BY A LICENSED ELECTRICIAN.
WARNING
THE ELECTRICITY MUST BE TURNED OFF AT THE MAIN FUSE BOX BEFORE
INSTALLING THIS LUMINAIRE. TURNING THE POWER OFF USING THE LIGHT
SWITCH MAY NOT BE SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
WOOD SCREWS MACHINE SCREWS WIRE NUTS EXPANSION ANCHORS
CANDELABRA BULB(S)
SUNLIGHT- 25R14FL-MED
REFLECTOR FLOOD- INDOOR R14
25 WATT-120V
SUNLIGHT- CAT # 01910
CANDELABRA BASE-25T6/CL BULB
25 WATT-120V CLEAR
SUNLIGHT- CAT # 01929
CANDELABRA BASE-25T8/CL BULB
25 WATT-120V CLEAR
SUNLITE- 40CFC CAT# 01345
CANDELABRA-BASE FLAME TIP
40 WATT-120V CLEAR
SUNLIGHT- CAT # 01105
HOUSEHOLD CLEAR
60 WATT-120
60A/CL
SUNLIGHT- 60CTC CAT # 01395
CANDELABRA BASE-TORPEDO TIP
60 WATT-120V CLEAR
SUNLIGHT- CAT # 01216
SILVER BOWL-A-19/CLEAR BULB
100 WATT-120/130V GLARE FREE
100ASB-SU
FERROWATT
40 WATT-120V CLEAR
SUNLIGHT- CAT # 03470
MEDIUM BASE-MR16 BULB
50 WATT-120V HALOGEN
SUNLIGHT
COMPACT FLUORESCENT
13 WATT-120V
SL13SP65-SU
SUNLITE-COMPACT FLOURESCENT
SLC14TW/30K
14 WATT-(INCANDESCENT EQUIVALENT 60 WATT)
CAT # 65700 WARM WHITE
SUNLIGHT- CAT # 05510
COMPACT FLUORESCENT
25 WATT- INCANDESCENT EQUIVALENT-100 WATTS
SLS25/65K-BX
WESTINGHOUSE # 03840
WHITE 580 LUMENS
60 WATT-120V
WESTINGHOUSE-TUBULAR-25W
STANDARD BASE
25 WATT-120V
03835 25T10/F

BELMONT WALL
ASSEMBLY AND MOUNTING INSTRUCTIONS MM-3900
MOUNTING INSTRUCTIONS
MOUNTING DIAGRAM ELECTRICAL CONFIGURATION TABLE
FROM HOME FROM LUMINAIRE
CONNECT BLACK OR RED (HOT)
HOUSE SUPPLY CIRCUIT WIRE TO:
LUMINAIRE ROUND WIRE (HOT)
CONNECT WHITE (NEUTRAL)
HOUSE SUPPLY CIRCUIT WIRE TO:
LUMINAIRE RIBBED WIRE
(NEUTRAL)
CONNECT GREEN INSULATED OR BARE COPPER (GROUND -) HOUSE
SUPPLY CIRCUIT WIRE AND LUMINAIRE BARE STRANDED WIRE
(GROUND -) TO GREEN GROUND SCREW ON CROSSBAR.
GENERAL NOTE: USE UL LISTED WIRE NUTS FOR THE
WIRING CONNECTIONS IN THIS LUMINAIRE. WRAP WIRE NUT
CONNECTIONS WITH UL LISTED ELECTRICAL TAPE.
FOR QUESTIONS, PLEASE CONTACT CLIENT SERVICES AT:
843.723.8140 OR [email protected]
STEP 1
SHUT OFF THE MAIN ELECTRICAL SUPPLY TO THE JUNCTION
BOX FROM THE FUSE BOX/CIRCUIT BREAKER. TURNING
POWER OFF AT THE SWITCH IS NOT SUFFICIENT. NOTE: IT IS
RECOMMENDED THAT THIS FIXTURE BE INSTALLED BY AT LEAST
TWO PEOPLE.
STEP 2
CAREFULLY SLIP FIXTURE WIRING THROUGH THE BRACKET AND
FEED OUT THE BACKPLATE. SEAT FIXTURE INTO BRACKET. WITH
ASSISTANCE, POSITION ASSEMBLED FIXTURE AND BRACKET AT
OR NEAR THE JUNCTION BOX.
STEP 3
USING THE WIRE NUTS PROVIDED, MAKE ELECTRICAL
CONNECTIONS BY FOLLOWING THE ELECTRICAL
CONFIGURATION TABLE BELOW. ENSURE THAT ALL
ELECTRICAL CONNECTIONS ARE WRAPPED WITH UL-LISTED
ELECTRICAL TAPE. IMPORTANT: NEVER ALLOW FIXTURE TO
“HANG” FROM ELECTRICAL CONNECTIONS OR TO OTHERWISE
PUT PRESSURE ON THE CONNECTIONS. DURING INSTALL, THE
WEIGHT OF THE FIXTURE SHOULD ALWAYS BE PROPERLY
SUPPORTED.
STEP 4
USING MOUNTING SCREWS AND EXPANSION ANCHORS
PROVIDED, ATTACH THE BRACKET TO THE WALL AT THE DESIRED
LOCATION, ENSURING THAT THE JUNCTION BOX HAS BEEN
COMPLETELY COVERED. IT IS IMPORTANT TO CHECK LEVEL ON
THE MOUNTED BRACKET.
STEP 5
INSTALL LIGHT BULB IN FIXTURE SOCKET AND RESTORE POWER
TO THE CIRCUIT.
STEP 6
CONFIRM PROPER OPERATION OF THE LIGHT FIXTURE.