Urban Electric ARCHIBALD Quick start guide

ARCHI B A LD
ARCHI B A LDARCHI B A LD
ARCHI B A LD
ASSEMBLY AND MOUNTING INSTRUCTIONS U E - 8 7 0 5
G E N E R A L N O T E S
G E N E R A L N O T E SG E N E R A L N O T E S
G E N E R A L N O T E S
•THIS LUMINAIRE IS SUITED FOR DAMP LOCATIONS.
•THIS LUMINAIRE IS UL LISTED. WHEN INSTALLING LUMINAIRE, CONFORM
TO ALL APPLICABLE LOCAL ELECTRICAL CODES, ORDINANCES, AND THE
NATIONAL ELECTRICAL CODE (NEC).
•FOR YOUR SAFETY AND PROPER OPERATION OF LUMINAIRE, READ AND
UNDERSTAND ALL INSTRUCTIONS COMPLETELY BEFORE COMMENCING
INSTALLATION OF THIS LUMINAIRE.
•CAREFULLY UNPACK THE LUMINAIRE AND INSPECT FOR DAMAGE.
•THIS PRODUCT IS RATED FOR ONE 0W MAX, TYPE B BULB.
•SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CAUTION
CAUTIONCAUTION
CAUTION
THIS PRODUCT SHOULD BE INSTALLED ONLY BY A LICENSED ELECTRICIAN.
PLEASE WEAR GLOVES TO PROTECT THE FINISH OF THE FIXTURE.
WARNING
WARNINGWARNING
WARNING
THE ELECTRICITY MUST BE TURNED OFF AT THE MAIN FUSE BOX BEFORE
INSTALLING THIS LUMINAIRE. TURNING POWER OFF USING THE LIGHT
SWITCH MAY NOT BE SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
C O M P O N E N T S P R O V I D E D F O R I N S T A L L A TI O N
C O M P O N E N T S P R O V I D E D F O R I N S T A L L A TI O NC O M P O N E N T S P R O V I D E D F O R I N S T A L L A TI O N
C O M P O N E N T S P R O V I D E D F O R I N S T A L L A TI O N
FIXTURE BODY
FIXTURE BODYFIXTURE BODY
FIXTURE BODY MOUNTING PLATE
MOUNTING PLATEMOUNTING PLATE
MOUNTING PLATE CANDELABRA BULB
CANDELABRA BULBCANDELABRA BULB
CANDELABRA BULB HEX WRENCH
HEX WRENCHHEX WRENCH
HEX WRENCH WIRE NUTS
WIRE NUTSWIRE NUTS
WIRE NUTS
WOOD SCREWS
WOOD SCREWSWOOD SCREWS
WOOD SCREWS
(X4)
(X4)(X4)
(X4)
EXPANSION ANCHORS
EXPANSION ANCHORSEXPANSION ANCHORS
EXPANSION ANCHORS
(X4)
(X4)(X4)
(X4)

ARCHI B A LD
ARCHI B A LDARCHI B A LD
ARCHI B A LD
ASSEMBLY AND MOUNTING INSTRUCTIONS U E - 8 7 0 5
M O U N T I N G I N S T R U C TI O N S
M O U N T I N G I N S T R U C TI O N SM O U N T I N G I N S T R U C TI O N S
M O U N T I N G I N S T R U C TI O N S
STEP 1
STEP 1STEP 1
STEP 1
SHUT OFF THE MAIN ELECTRICAL SUPPLY TO THE JUNCTION
BOX FROM THE FUSE BOX/CIRCUIT BREAKER. TURNING
POWER OFF AT THE SWITCH IS NOT SUFFICIENT.
STEP 2
STEP 2STEP 2
STEP 2
LOOSEN THE FOUR PAN HEAD SCREWS AT THE TOP & BOTTOM
OF THE FIXTURE FRAME AND REMOVE THE MIRRORED
BACKPLATE FROM THE BACK OF THE FIXTURE. PLACE THE
FIXTURE ASIDE.
STEP 3
STEP 3STEP 3
STEP 3
USING THE PROVIDED HEX WRENCH, LOOSEN THE TWO SET
SCREWS AT THE BOTTOM OF THE MIRRORED BACKPLATE
ENOUGH TO REMOVE THE MOUNTING PLATE. PLACE THE
MIRRORED BACKPLATE ASIDE.
STEP 4
STEP 4STEP 4
STEP 4
PULL HOUSE SUPPLY CIRCUIT WIRING THROUGH THE WIRE-WAY
OF THE MOUNTING PLATE. ATTACH THE MOUNTING PLATE TO
THE JUNCTION BOX USING THE JUNCTION BOX SCREWS AND/OR
THE WOOD SCREWS AND EXPANSION ANCHORS PROVIDED. IT IS
IMPORTANT TO CHECK LEVEL ON THE MOUNTING PLATE.

ARCHI B A LD
ARCHI B A LDARCHI B A LD
ARCHI B A LD
ASSEMBLY AND MOUNTING INSTRUCTIONS U E - 8 7 0 5
STEP 5
STEP 5STEP 5
STEP 5
USING THE WIRE NUTS PROVIDED, MAKE ELECTRICAL
CONNECTIONS BY FOLLOWING THE ELECTRICAL CONFIGURATION
TABLE BELOW. ENSURE THAT ALL ELECTRICAL CONNECTIONS
ARE WRAPPED WITH UL-LISTED ELECTRICAL TAPE.
STEP
STEP STEP
STEP
ATTACH THE MIRRORED BACKPLATE TO THE WALL BY SLIPPING
THE FIXTURE OVER THE MOUNTING PLATE AND TIGHTENING THE
TWO SET SCREWS AT THE BOTTOM OF THE BACKPLATE. BE
CAREFUL TO AVOID SCRATCHING THE FINISH ON THE FIXTURE.
STEP 7
STEP 7STEP 7
STEP 7
INSTALL THE LIGHT BULB IN THE FIXTURE SOCKET AND RESTORE
POWER TO THE FIXTURE. CONFIRM PROPER OPERATION OF THE
LIGHT FIXTURE.
STEP 8
STEP 8STEP 8
STEP 8
ATTACH THE FIXTURE TO THE MIRRORED BACKPLATE BY
SLIPPING THE FIXTURE OVER THE BACKPLATE AND RE-ATTACH
THE FOUR PAN HEAD SCREWS AT THE BOTTOM & TOP OF THE
FIXTURE. BE CAREFUL TO AVOID SCRATCHING THE FINISH ON
THE FIXTURE.
E L E C TR I C A L C O N F I G U R A T I O N T A B L E
E L E C TR I C A L C O N F I G U R A T I O N T A B L EE L E C TR I C A L C O N F I G U R A T I O N T A B L E
E L E C TR I C A L C O N F I G U R A T I O N T A B L E
F R O M H O M E
F R O M H O M EF R O M H O M E
F R O M H O M E F R O M L U M I N A I R E
F R O M L U M I N A I R EF R O M L U M I N A I R E
F R O M L U M I N A I R E GENERAL NOTE:
GENERAL NOTE:GENERAL NOTE:
GENERAL NOTE: USE UL LISTED WIRE NUTS FOR THE
WIRING CONNECTIONS IN THIS LUMINAIRE. WRAP WIRE
NUT CONNECTIONS WITH UL LISTED ELECTRICAL TAPE.
FOR QUESTIONS, PLEASE CONTACT CLIENT SERVICES
AT: 843.723.8140 OR [e-mail]
CONNECT BLACK OR RED (HOT)
HOUSE SUPPLY CIRCUIT WIRE
TO:
LUMINAIRE ROUND/BLACK WIRE
(HOT)
CONNECT WHITE (NEUTRAL)
HOUSE SUPPLY CIRCUIT WIRE
TO:
LUMINAIRE RIBBED/WHITE WIRE
(NEUTRAL)
CONNECT GREEN INSULATED OR BARE COPPER (GROUND
-
)
HOUSE SUPPLY CIRCUIT WIRE AND LUMINAIRE BARE STRANDED
WIRE (GROUND -) TO GREEN GROUND SCREW ON MOUNTING
PLATE