Urban Electric GAS VIC Quick start guide

GAS VIC (AUTO-IGNITE)
ASSEMBLY AND MOUNTING INSTRUCTIONS UE-1744
GENERAL NOTES
•THIS LUMINAIRE IS SUITED FOR WET LOCATIONS.
•WHEN INSTALLING LUMINAIRE, CONFORM TO ALL APPLICABLE
LOCAL CODES OR IN THE ABSENCE OF LOCAL CODES, WITH THE
NATIONAL FUEL GAS CODE.
•FOR YOUR SAFETY AND PROPER OPERATION OF LUMINAIRE, READ
AND UNDERSTAND ALL INSTRUCTIONS COMPLETELY BEFORE
COMMENCING INSTALLATION OF THIS LUMINAIRE.
•CAREFULLY UNPACK THE LUMINAIRE AND INSPECT FOR DAMAGE.
•SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CAUTION
•THIS PRODUCT SHOULD BE INSTALLED ONLY BY A LICENSED
ELECTRICIAN/GAS PLUMBER. PLEASE WEAR GLOVES TO PROTECT
THE FINISH OF THE FIXTURE.
MAINTENANCE INSTRUCTIONS
•KEEP APPLIANCE CLEAR AND FREE FROM COMBUSTIBLE
MATERIALS, GASOLINE AND OTHER FLAMMABLE VAPORS AND
LIQUIDS
•DO NOT OBSTRUCT THE FLOW OF COMBUSTION AND VENTILATION
AIR.
•VISUALLY CHECK THE BURNER AND PILOT FLAMES WITH PICTORIAL
REPRESENTATIONS.
•FOR QUESTIONS OR REPLACEMENT PARTS, PLEASE CONTACT
CLIENT SERVICES AT 843.723.8140 OR
[e-mail]
WARNINGS
FOR APPLIANCES FOR INDOOR INSTALLATION: FOR APPLIANCES FOR OUTDOOR
INSTALLATION:
FOR ALL APPLIANCES:
DANGER
FIRE OR EXPLOSION HAZARD
IF YOU SMELL GAS:
1. SHUT OFF GAS TO THE APPLIANCE.
2. OPEN WINDOWS.
3. DON’T TOUCH ELECTRICAL
SWITCHES.
4. EXTINGUISH ANY OPEN FLAME.
5. LEAVE THE BUILDING
IMMEDIATELY.
6. AFTER LEAVING THE BUILDING,
IMMEDIATELY CALL YOUR GAS
SUPPLIER OR FIRE DEPARTMENT.
DANGER
FIRE OR EXPLOSION HAZARD
IF YOU SMELL GAS:
1. SHUT OFF GAS TO APPLIANCE.
2. EXTINGUISH ANY OPEN FLAME.
3. IF ODOR CONTINUES, LEAVE THE
AREA IMMEDIATELY.
4. AFTER LEAVING THE AREA, CALL
YOUR GAS SUPPLIER OR FIRE
DEPARTMENT.
WARNING
FIRE OR EXPLOSION HAZARD
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE
VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER
APPLIANCE.

GAS VIC (AUTO-IGNITE)
ASSEMBLY AND MOUNTING INSTRUCTIONS UE-1744
•FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN FIRE OR
EXPLOSION, WHICH COULD CAUSE PROPERTY DAMAGE, PERSONAL INJURY,
OR DEATH.
COMPONENTS PROVIDED FOR INSTALLATION
FIXTURE FRAME
BURNER ASSEMBLY
BURNER COVER
BACK GLASS PANE
(002)
SIDE GLASS PANE (X2)
(003)
DOOR GLASS PANE
(001)
MOUNTING ANCHORS
(X4)
WOOD SCREWS
(X4)
GLASS RETAINING
CLIP
(X8)
24VAC 5VA POWER
TRANSFORMER
MOUNTING INSTRUCTIONS
STEP 1
ENSURE GAS LINE IS SHUT OFF OR GAS SUPPLY IS
OTHERWISE SECURED.
STEP 2
USING THE PROVIDED HEX WRENCH, LOOSEN THE TWO
SET SCREWS AT THE BOTTOM OF THE FIXTURE. REMOVE
THE MOUNTING PLATE FROM THE BACK OF THE FIXTURE
AND PLACE THE FIXTURE ASIDE.

GAS VIC (AUTO-IGNITE)
ASSEMBLY AND MOUNTING INSTRUCTIONS UE-1744
STEP 3
ATTACH THE MOUNTING PLATE TO THE WALL USING THE
FOUR MOUNTING SCREWS AND ANCHORS PROVIDED. IT IS
IMPORTANT TO CHECK LEVEL ON THE MOUNTING PLATE.
STEP 4
ATTACH THE FIXTURE TO THE WALL BY SLIPPING THE
FIXTURE OVER THE MOUNTING PLATE AND TIGHTENING THE
TWO SET SCREWS AT THE BOTTOM OF THE FIXTURE. BE
CAREFUL TO AVOID SCRATCHING THE FINISH ON THE
FIXTURE.
**MAKE SURE YOUR GAS SUPPLY LINE IS ROUTED THROUGH
NOTCH AT THE BOTTOM OF THE BACKPLATE BEFORE
ATTACHING THE FIXTURE TO THE WALL.
STEP 5
REMOVE THE DOOR LATCH PIN AND OPEN THE DOOR OF THE
FIXTURE. INSTALL THE DOOR GLASS (001) PANE BY
INSERTING THE TOP EDGE OF THE GLASS PANE INTO THE
CHANNEL AT THE TOP OF THE DOOR. ONCE THE TOP EDGE
OF GLASS IS IN PLACE, GENTLY STRAIGHTEN THE PANE AND
LOWER IT INTO THE CHANNEL AT THE BOTTOM OF THE DOOR.
INSTALL THE TWO GLASS RETAINING CLIPS ON THE INSIDE OF
THE GLASS IN THE TOP AND BOTTOM CHANNEL TO SECURE
THE GLASS PANE.
STEP 6
WITH THE FIXTURE DOOR OPEN, REMOVE THE TWO ACORN
NUTS AND THE GLASS SUPPORT PAN AT THE INSIDE TOP OF
THE FIXTURE AND SET ASIDE.

GAS VIC (AUTO-IGNITE)
ASSEMBLY AND MOUNTING INSTRUCTIONS UE-1744
STEP 7
INSTALL THE SIDE GLASS PANE (002) BY INSERTING THE
BOTTOM EDGE OF THE GLASS PANE INTO THE CHANNEL AT
THE BOTTOM OF THE FIXTURE. ONCE THE BOTTOM EDGE OF
GLASS IS IN PLACE, GENTLY STRAIGHTEN THE PANE OF
GLASS TO BE FLUSH WITH FRAME BODY. INSTALL A GLASS
RETAINING CLIP ON THE INSIDE OF THE GLASS IN THE
BOTTOM CHANNEL TO SECURE THE GLASS PANE. REPEAT
FOR THE REMAINING TWO PANES OF GLASS.
STEP 8
WITH THE FIXTURE DOOR OPEN, RE-INSTALL THE GLASS
SUPPORT PAN BY SLIPPING THE PAN OVER THE TOP STUDS
AND SECURE IN PLACE WITH THE TWO ACORN NUTS. FINALLY
INSTALL THE THREE REMAINING GLASS RETAINING CLIPS ON
THE INSIDE OF THE GLASS IN THE TOP CHANNEL TO SECURE
THE THREE GLASS PANES.
STEP 9
WITH THE FIXTURE DOOR OPEN, REMOVE THE TWO ACORN
NUTS AT THE BASE OF THE FIXTURE AND SET ASIDE.
STEP 10
ATTACH THE BURNER ASSEMBLY TO THE BASE OF THE
FIXTURE AND SECURE USING THE TWO ACORN NUTS
REMOVED IN STEP 9.

GAS VIC (AUTO-IGNITE)
ASSEMBLY AND MOUNTING INSTRUCTIONS UE-1744
STEP 11A
ROUTE GAS LINE. APPLY A THIN LAYER OF PIPE DOPE OR
THREAD SEALANT TO THE THREADED FITTINGS. CONNECT
THE GAS SUPPLY TO THE LANTERN AND HAND TIGHTEN ALL
FITTINGS. ENSURE THAT THE FITTINGS ARE NOT CROSS-
THREADED. CONTINUE TO TIGHTEN WITH THE APPROPRIATE
SIZED WRENCHES.
STEP 11B
CONNECT 120V HOUSE SUPPLY TO (120V) PRIMARY SIDE OF
TRANSFORMER
CONNECT BURNER ASSEMBLY WIRES TO (24V) SECONDARY
SIDE OF TRANSFORMER
STEP 12
SLIP THE BURNER COVER OVER THE BURNER ASSEMBLY.
STEP 13
OPEN THE GAS VALVE JUST ENOUGH TO IGNITE A FLAME AT
THE BURNER TIP.
STEP 14
ADJUST THE FLAME TO YOUR PREFERENCE BY ADJUSTING
THE LEVER POSITION OF THE MANUAL GAS VALVE. WE
RECOMMEND THAT THE FLAME BE NO LARGER THAN 2
INCHES IN HEIGHT.
STEP 15
IMPORTANT: IF THE FIXTURE IS INSTALLED IN AN EXTERIOR
LOCATION, RUN A BEAD OF SEALANT AROUND THE
PERIMETER OF THE BACKPLATE TO PREVENT WATER
FROM GETTING BEHIND THE BACKPLATE.