Urban Electric PAM POCKET Quick start guide

PAM P O CKE T
PAM P O CKE TPAM P O CKE T
PAM P O CKE T
ASSEMBLY AND MOUNTING INSTRUCTIONS M A - 8 0 2 8
G E N E R A L N O T E S
G E N E R A L N O T E SG E N E R A L N O T E S
G E N E R A L N O T E S
•THIS LUMINAIRE IS SUITED FOR DAMP LOCATIONS.
•THIS LUMINAIRE IS UL LISTED. WHEN INSTALLING LUMINAIRE,
CONFORM TO ALL APPLICABLE LOCAL ELECTRICAL CODES,
ORDINANCES, AND THE NATIONAL ELECTRICAL CODE (NEC).
•FOR YOUR SAFETY AND PROPER OPERATION OF LUMINAIRE, READ
AND UNDERSTAND ALL INSTRUCTIONS COMPLETELY BEFORE
COMMENCING INSTALLATION OF THIS LUMINAIRE.
•CAREFULLY UNPACK THE LUMINAIRE AND INSPECT FOR DAMAGE.
•THIS PRODUCT IS RATED FOR:
oWALL REGULAR: ONE 0W MAX, TYPE B BULB.
oWALL LARGE: TWO 0W MAX, TYPE B BULBS.
•SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CAUTION
CAUTIONCAUTION
CAUTION
THIS PRODUCT SHOULD BE INSTALLED ONLY BY A LICENSED
ELECTRICIAN.
WARNING
WARNINGWARNING
WARNING
THE ELECTRICITY MUST BE TURNED OFF AT THE MAIN FUSE BOX BEFORE
INSTALLING THIS LUMINAIRE. TURNING POWER OFF USING THE LIGHT
SWITCH MAY NOT BE SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
C O M P O N E N T S P R O V I D E D F O R I N S T A L L A T I O N
C O M P O N E N T S P R O V I D E D F O R I N S T A L L A T I O NC O M P O N E N T S P R O V I D E D F O R I N S T A L L A T I O N
C O M P O N E N T S P R O V I D E D F O R I N S T A L L A T I O N
(X4)
(X4) (X4)
(X4)
WOOD SCREWS
WOOD SCREWSWOOD SCREWS
WOOD SCREWS
(X4)
(X4) (X4)
(X4)
WALL ANCHORS
WALL ANCHORSWALL ANCHORS
WALL ANCHORS
MOUNTING PLATE
MOUNTING PLATEMOUNTING PLATE
MOUNTING PLATE
TUBULAR BULB
TUBULAR BULBTUBULAR BULB
TUBULAR BULB
WIRE NUTS
WIRE NUTSWIRE NUTS
WIRE NUTS HEX WRENCH
HEX WRENCHHEX WRENCH
HEX WRENCH

PAM P O CKE T
PAM P O CKE TPAM P O CKE T
PAM P O CKE T
ASSEMBLY AND MOUNTING INSTRUCTIONS M A - 8 0 2 8
M O U N T I N G I N S T R U C T I O N S
M O U N T I N G I N S T R U C T I O N SM O U N T I N G I N S T R U C T I O N S
M O U N T I N G I N S T R U C T I O N S
STEP 1
STEP 1STEP 1
STEP 1
SHUT OFF THE MAIN ELECTRICAL SUPPLY TO THE JUNCTION
BOX FROM THE FUSE BOX/CIRCUIT BREAKER. TURNING
POWER OFF AT THE SWITCH IS NOT SUFFICIENT.
STEP 2
STEP 2STEP 2
STEP 2
USING THE HEX WRENCH PROVIDED, LOOSEN THE SET
SCREWS AT THE BOTTOM OF THE FIXTURE ENOUGH TO
REMOVE THE MOUNTING PLATE FROM THE BACK OF THE
FIXTURE. SET THE FIXTURE AND SET SCREWS ASIDE.
STEP 3
STEP 3STEP 3
STEP 3
LOCATE THE JUNCTION BOX AND PULL HOUSE SUPPLY CIRCUIT
WIRING THROUGH THE WIRE-WAY HOLE OF THE MOUNTING
PLATE. ATTACH THE MOUNTING PLATE DIRECTLY TO THE
JUNCTION BOX USING THE JUNCTION BOX SCREWS AND
DIRECTLY TO THE WALL SURFACE USING THE MOUNTING
SCREWS AND EXPANSION ANCHORS PROVIDED. IT IS IMPORTANT
TO CHECK LEVEL ON THE MOUNTED WALL PLATE.
STEP 4
STEP 4STEP 4
STEP 4
USING THE WIRE NUTS PROVIDED, MAKE ELECTRICAL
CONNECTIONS BY FOLLOWING THE ELECTRICAL CONFIGURATION
TABLE ON THE LAST PAGE. ENSURE THAT ALL ELECTRICAL
CONNECTIONS ARE WRAPPED WITH UL-LISTED ELECTRICAL
TAPE.

PAM P O CKE T
PAM P O CKE TPAM P O CKE T
PAM P O CKE T
ASSEMBLY AND MOUNTING INSTRUCTIONS M A - 8 0 2 8
S
SS
STEP 5
TEP 5TEP 5
TEP 5
ATTACH THE FIXTURE TO THE MOUNTING PLATE BY SLIDING THE
FIXTURE OVER THE TOP OF THE MOUNTING PLATE AND THEN
SECURE THE FIXTURE AT THE BOTTOM WITH THE SET SCREWS.
BE CAREFUL TO AVOID SCRATCHING THE FINISH ON THE
FIXTURE.
IMPORTANT: IF THE FIXTURE IS INSTALLED IN AN EXTERIOR
LOCATION, RUN A SMALL BEAD OF SEALANT AROUND THE
PERIMETER OF THE BACKPLATE TO PREVENT WATER FROM
REACHING THE WIRE CONNECTIONS.
STEP
STEP STEP
STEP
INSTALL LIGHT BULB IN FIXTURE SOCKET AND RESTORE POWER
TO THE CIRCUIT. CONFIRM PROPER OPERATION OF THE LIGHT
FIXTURE.
E L E C T R I C A L C O N F I G U R A T I O N T A B L E
E L E C T R I C A L C O N F I G U R A T I O N T A B L EE L E C T R I C A L C O N F I G U R A T I O N T A B L E
E L E C T R I C A L C O N F I G U R A T I O N T A B L E
F R O M H O M E
F R O M H O M EF R O M H O M E
F R O M H O M E F R O M L U M I N A I R E
F R O M L U M I N A I R EF R O M L U M I N A I R E
F R O M L U M I N A I R E GENERAL NOTE:
GENERAL NOTE:GENERAL NOTE:
GENERAL NOTE: USE UL LISTED WIRE NUTS FOR THE
WIRING CONNECTIONS IN THIS LUMINAIRE. WRAP WIRE
NUT CONNECTIONS WITH UL LISTED ELECTRICAL TAPE.
FOR QUESTIONS, PLEASE CONTACT CLIENT SERVICES
AT: 843.723.8140 OR [e-mail]
CONNECT BLACK OR RED (HOT)
HOUSE SUPPLY CIRCUIT WIRE TO:
LUMINAIRE ROUND/BLACK WIRE
(HOT)
CONNECT WHITE (NEUTRAL)
HOUSE SUPPLY CIRCUIT WIRE TO:
LUMINAIRE RIBBED/WHITE WIRE
(NEUTRAL)
CONNECT GREEN INSULATED OR BARE COPPER (GROUND -) HOUSE
SUPPLY CIRCUIT WIRE AND LUMINAIRE BARE STRANDED WIRE
(GROUND -) TO GREEN GROUND SCREW ON CROSSBAR.