Urban Electric DUNHILL Quick start guide

MA-1350
DUNHILL
ASSEMBLY AND MOUNTING INSTRUCTIONS
GENERAL NOTES
COMPONENTS PROVIDED FOR INSTALLATION
• THIS LUMINAIRE IS SUITED FOR WET LOCATIONS.
• THIS LUMINAIRE IS UL LISTED. WHEN INSTALLING LUMINAIRE, CONFORM
TO ALL APPLICABLE LOCAL ELECTRICAL CODES, ORDINANCES, AND THE
NATIONAL ELECTRICAL CODE (NEC).
• FOR YOUR SAFETY AND PROPER OPERATION OF LUMINAIRE, READ AND
UNDERSTAND ALL INSTRUCTIONS COMPLETELY BEFORE COMMENCING
INSTALLATION OF THIS LUMINAIRE.
• CAREFULLY UNPACK THE LUMINAIRE AND INSPECT FOR DAMAGE.
• THIS PRODUCT IS RATED FOR ONE 60W MAX, TYPE A BULB(S).
• SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CAUTION
THIS PRODUCT SHOULD BE INSTALLED ONLY BY A LICENSED ELECTRICIAN.
WARNING
THE ELECTRICITY MUST BE TURNED OFF AT THE MAIN FUSE BOX BEFORE
INSTALLING THIS LUMINAIRE. TURNING THE POWER OFF USING THE LIGHT
SWITCH MAY NOT BE SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
DUNHILL MOUNTING PLATE WOOD SCREWS SET SCREWS WALL ANCHOR
TUBULAR STANDARD
BASE BULB ALLEN WRENCH

DUNHILL
ASSEMBLY AND MOUNTING INSTRUCTIONS MA-1350
MOUNTING INSTRUCTIONS
MOUNTING DIAGRAM ELECTRICAL CONFIGURATION TABLE
FROM HOME FROM LUMINAIRE
CONNECT BLACK OR RED (HOT)
HOUSE SUPPLY CIRCUIT WIRE TO:
LUMINAIRE ROUND WIRE (HOT)
CONNECT WHITE (NEUTRAL)
HOUSE SUPPLY CIRCUIT WIRE TO:
LUMINAIRE RIBBED WIRE
(NEUTRAL)
CONNECT GREEN INSULATED OR BARE COPPER (GROUND -) HOUSE
SUPPLY CIRCUIT WIRE AND LUMINAIRE BARE STRANDED WIRE
(GROUND -) TO GREEN GROUND SCREW ON CROSSBAR.
GENERAL NOTE: USE UL LISTED WIRE NUTS FOR THE
WIRING CONNECTIONS IN THIS LUMINAIRE. WRAP WIRE NUT
CONNECTIONS WITH UL LISTED ELECTRICAL TAPE.
FOR QUESTIONS, PLEASE CONTACT CLIENT SERVICES AT:
843.723.8140 OR [email protected]
STEP 1
SHUT OFF THE MAIN ELECTRICAL SUPPLY TO THE JUNCTION
BOX FROM THE FUSE BOX/CIRCUIT BREAKER. TURNING POWER
OFF AT THE SWITCH IS NOT SUFFICIENT.
STEP 2
REMOVE MOUNTING PLATE FROM BACK OF THE FIXTURE USING
THE ALLEN WRENCH PROVIDED AND SET FIXTURE SCREWS
ASIDE.
STEP 3
LOCATE JUNCTION BOX AND PULL HOUSE SUPPLY CIRCUIT
WIRING THROUGH THE WIRE-WAY HOLE OF THE MOUNTING PLATE.
ATTACH THE MOUNTING PLATE DIRECTLY TO THE JUNCTION BOX
AND/OR DIRECTLY TO THE WALL SURFACE USING THE MOUNTING
SCREWS AND EXPANSION ANCHORS PROVIDED. IT IS IMPORTANT
TO CHECK LEVEL ON THE MOUNTED WALL PLATE.
STEP 4
USING THE WIRE NUTS PROVIDED MAKE ELECTRICAL
CONNECTIONS BY FOLLOWING THE ELECTRICAL CONFIGURATION
TABLE BELOW. ENSURE THAT ALL ELECTRICAL CONNECTIONS
ARE WRAPPED WITH UL-LISTED ELECTRICAL TAPE.
STEP 5
ATTACH THE FIXTURE TO THE MOUNTING PLATE BY SLIDING THE
FIXTURE OVER THE TOP OF THE MOUNTING PLATE AND THEN
SECURE THE FIXTURE AT THE BOTTOM WITH THE SET SCREWS
PROVIDED. BE CAREFUL TO AVOID SCRATCHING THE FINISH ON
THE FIXTURE.
STEP 6
TO INSTALL BULB AND GLASS IN FIXTURE, REMOVE THE TWO
SLOTTED SCREWS FROM THE TOP OF THE FIXTURE AND REMOVE
THE CAP
STEP 7
INSTALL LIGHT BULB/S IN FIXTURE SOCKET AND RESTORE
POWER TO THE CIRCUIT.
STEP 7
CONFIRM PROPER OPERATION OF THE LIGHT FIXTURE.
GLASS INSTALL
REMOVE 2 TOP SCREWS OF UPPER ARM AND SLIDE GLASS OVER
ELECTRICAL ASSEMBLY THEN FASTEN 2 SCREWS TO UPPER ARM.