Urban Electric ALLEN Quick start guide

ALLEN
ALLENALLEN
ALLEN
ASSEMBLY AND MOUNTING INSTRUCTIONS U E - 8 4 4 0
G E N E R A L N O T E S
G E N E R A L N O T E SG E N E R A L N O T E S
G E N E R A L N O T E S
•THIS LUMINAIRE IS SUITED FOR DAMP LOCATIONS.
•THIS LUMINAIRE IS UL LISTED. WHEN INSTALLING LUMINAIRE,
CONFORM TO ALL APPLICABLE LOCAL ELECTRICAL CODES,
ORDINANCES, AND THE NATIONAL ELECTRICAL CODE (NEC).
•FOR YOUR SAFETY AND PROPER OPERATION OF LUMINAIRE, READ
AND UNDERSTAND ALL INSTRUCTIONS COMPLETELY BEFORE
COMMENCING INSTALLATION OF THIS LUMINAIRE.
•CAREFULLY UNPACK THE LUMINAIRE AND INSPECT FOR DAMAGE.
•THIS PRODUCT IS RATED FOR ONE 60W MA , TYPE B BULB.
•SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CAUTION
CAUTIONCAUTION
CAUTION
THIS PRODUCT SHOULD BE INSTALLED ONLY BY A LICENSED
ELECTRICIAN.
WARNING
WARNINGWARNING
WARNING
THE ELECTRICITY MUST BE TURNED OFF AT THE MAIN FUSE BO BEFORE
INSTALLING THIS LUMINAIRE. TURNING POWER OFF USING THE LIGHT
SWITCH MAY NOT BE SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
C O M P O N E N T S P R O V I D E D F O R I N S T A L L A TI O N
C O M P O N E N T S P R O V I D E D F O R I N S T A L L A TI O NC O M P O N E N T S P R O V I D E D F O R I N S T A L L A TI O N
C O M P O N E N T S P R O V I D E D F O R I N S T A L L A TI O N
NIPPLE
NIPPLENIPPLE
NIPPLE
CAP
CAPCAP
CAP
WIRE NUTS
WIRE NUTSWIRE NUTS
WIRE NUTS
CROSSBAR
CROSSBARCROSSBAR
CROSSBAR
CANDELABRA BULB
CANDELABRA BULBCANDELABRA BULB
CANDELABRA BULB

ALLEN
ALLENALLEN
ALLEN
ASSEMBLY AND MOUNTING INSTRUCTIONS U E - 8 4 4 0
M O UN T I N G I N S TR U C T I O NS
M O UN T I N G I N S TR U C T I O NSM O UN T I N G I N S TR U C T I O NS
M O UN T I N G I N S TR U C T I O NS
STEP 1
STEP 1STEP 1
STEP 1
SHUT OFF THE MAIN ELECTRICAL SUPPLY TO THE JUNCTION
BO FROM THE FUSE BO /CIRCUIT BREAKER. TURNING
POWER OFF AT THE SWITCH IS NOT SUFFICIENT.
STEP 2
STEP 2STEP 2
STEP 2
LOCATE THE JUNCTION BO ON THE WALL. ATTACH THE
PROVIDED CROSS BAR TO THE JUNCTION BO USING THE
JUNCTION BO SCREWS.
STEP 3
STEP 3STEP 3
STEP 3
USING THE WIRE NUTS PROVIDED, MAKE ELECTRICAL
CONNECTIONS BY FOLLOWING THE ELECTRICAL CONFIGURATION
TABLE BELOW. ENSURE THAT ALL ELECTRICAL CONNECTIONS
ARE WRAPPED WITH UL LISTED ELECTRICAL TAPE.
STEP 4
STEP 4STEP 4
STEP 4
ATTACH THE FI TURE TO THE CROSS-BAR USING THE THREADED
NIPPLE AND CAP PROVIDED. BE CAREFUL TO AVOID SCRATCHING
THE FINISH ON THE FI TURE.
STEP
STEP STEP
STEP 5
55
5
INSTALL LIGHT BULB IN FI TURE SOCKET AND RESTORE POWER
TO THE CIRCUIT.
STEP
STEP STEP
STEP 6
66
6
CONFIRM PROPER OPERATION OF THE LIGHT FI TURE.
E L EC T R I C A L C O N F I G U R A T I O N T A B L E
E L EC T R I C A L C O N F I G U R A T I O N T A B L EE L EC T R I C A L C O N F I G U R A T I O N T A B L E
E L EC T R I C A L C O N F I G U R A T I O N T A B L E
F R O M H O M E
F R O M H O M EF R O M H O M E
F R O M H O M E F R O M L U M I N A I R E
F R O M L U M I N A I R EF R O M L U M I N A I R E
F R O M L U M I N A I R E
GENERAL NOTE:
GENERAL NOTE:GENERAL NOTE:
GENERAL NOTE: USE UL LISTED WIRE NUTS FOR THE
WIRING CONNECTIONS IN THIS LUMINAIRE. WRAP WIRE
NUT CONNECTIONS WITH UL LISTED ELECTRICAL TAPE.
FOR QUESTIONS, PLEASE CONTACT CLIENT SERVICES AT:
843.723.8140 OR [e-mail]
CONNECT BLACK OR RED (HOT)
HOUSE SUPPLY CIRCUIT WIRE
TO:
LUMINAIRE ROUND WIRE (HOT)
CONNECT WHITE (NEUTRAL)
HOUSE SUPPLY CIRCUIT WIRE
TO:
LUMINAIRE RIBBED WIRE
(NEUTRAL)
CONNECT GREEN INSULATED OR BARE COPPER (GROUND -)
HOUSE SUPPLY CIRCUIT WIRE AND LUMINAIRE BARE STRANDED
WIRE (GROUND -) TO GREEN GROUND SCREW ON CROSSBAR.