Urban Electric CLIPPER Quick start guide

MA-1540
CLIPPER
ASSEMBLY AND MOUNTING INSTRUCTIONS
GENERAL NOTES
COMPONENTS PROVIDED FOR INSTALLATION
MOUNTING PLATE #6 WOOD SCREWS #6 MACHINE SCREWS SET SCREWS
HEX WRENCH WALL ANCHORS WIRE NUTS HOUSEHOLD BULB(S)
• THIS LUMINAIRE IS SUITED FOR WET LOCATIONS.
• THIS LUMINAIRE IS UL LISTED. WHEN INSTALLING LUMINAIRE, CONFORM
TO ALL APPLICABLE LOCAL ELECTRICAL CODES, ORDINANCES, AND THE
NATIONAL ELECTRICAL CODE (NEC).
• FOR YOUR SAFETY AND PROPER OPERATION OF LUMINAIRE, READ AND
UNDERSTAND ALL INSTRUCTIONS COMPLETELY BEFORE COMMENCING
INSTALLATION OF THIS LUMINAIRE.
• CAREFULLY UNPACK THE LUMINAIRE AND INSPECT FOR DAMAGE.
• THIS PRODUCT IS RATED ONE 60W MAX, TYPE A BULB(S).
• SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CAUTION
THIS PRODUCT SHOULD BE INSTALLED ONLY BY A LICENSED ELECTRICIAN.
WARNING
THE ELECTRICITY MUST BE TURNED OFF AT THE MAIN FUSE BOX BEFORE
INSTALLING THIS LUMINAIRE. TURNING THE POWER OFF USING THE LIGHT
SWITCH MAY NOT BE SUFFICIENT TO PREVENT ELECTRICAL SHOCK.

CLIPPER
ASSEMBLY AND MOUNTING INSTRUCTIONS MA-1540
MOUNTING INSTRUCTIONS
STEP 1
SHUT OFF THE MAIN ELECTRICAL SUPPLY TO THE JUNCTION
BOX FROM THE FUSE BOX/CIRCUIT BREAKER. TURNING POWER
OFF AT THE SWITCH IS NOT SUFFICIENT.
STEP 2
REMOVE MOUNTING PLATE BY REMOVING BOTTOM SET
SCREWS ONLY FROM THE BACK OF THE FIXTURE (USUALLY
SHIPPED WITH SET SCREWS ATTACHED) AND SET FIXTURE AND
SET SCREWS ASIDE.
STEP 3
LOCATE JUNCTION BOX AND PULL HOUSE SUPPLY CIRCUIT
WIRING THROUGH THE WIRE-WAY OF THE SEPARATE
MOUNTING PLATE.
STEP 4
LOCATE THE JUNCTION BOX AND ATTACH THE MOUNTING PLATE
USING THE MACHINE SCREWS PROVIDED OR MOUNT DIRECTLY
TO THE WALL WITH THE WOOD SCREWS AND WALL ANCHORS
PROVIDED.
STEP 5
USING THE WIRE NUTS PROVIDED, MAKE ELECTRICAL
CONNECTIONS BY FOLLOWING THE ELECTRICAL
CONFIGURATION TABLE ON THE NEXT PAGE. ENSURE THAT ALL
ELECTRICAL CONNECTIONS ARE WRAPPED WITH UL-LISTED
ELECTRICAL TAPE.
STEP 6
ATTACH THE FIXTURE TO THE WALL PLATE BY SLIPPING IT OVER
THE WALL PLATE AND TIGHTENING THE BOTTOM SET SCREWS
PROVIDED. BE CAREFUL TO AVOID SCRATCHING THE FINISH ON
THE FIXTURE.
STEP 7
INSTALL LIGHT BULB IN FIXTURE SOCKET AND RESTORE POWER
TO THE CIRCUIT.
STEP 8
CONFIRM PROPER OPERATION OF THE LIGHT FIXTURE.
STEP 9
IF THE FIXTURE IS INSTALLED IN AN EXTERIOR LOCATION, RUN
A SMALL BEAD OF SEALANT AROUND THE PERIMETER OF THE
BACKPLATE TO PREVENT WATER FROM REACHING THE WIRE
CONNECTIONS.
STEP 2 STEP 4 STEP 6

CLIPPER
ASSEMBLY AND MOUNTING INSTRUCTIONS MA-1540
MOUNTING DIAGRAM
ELECTRICAL CONFIGURATION TABLE
FROM HOME FROM LUMINAIRE
CONNECT BLACK OR RED (HOT)
HOUSE SUPPLY CIRCUIT WIRE TO:
LUMINAIRE ROUND WIRE (HOT)
CONNECT WHITE (NEUTRAL)
HOUSE SUPPLY CIRCUIT WIRE TO:
LUMINAIRE RIBBED WIRE
(NEUTRAL)
CONNECT GREEN INSULATED OR BARE COPPER (GROUND -) HOUSE
SUPPLY CIRCUIT WIRE AND LUMINAIRE BARE STRANDED WIRE
(GROUND -) TO GREEN GROUND SCREW ON CROSSBAR.
GENERAL NOTE: USE UL LISTED WIRE NUTS FOR THE
WIRING CONNECTIONS IN THIS LUMINAIRE. WRAP WIRE NUT
CONNECTIONS WITH UL LISTED ELECTRICAL TAPE.
FOR QUESTIONS, PLEASE CONTACT CLIENT SERVICES AT:
843.723.8140 OR [email protected]

CLIPPER
ASSEMBLY AND MOUNTING INSTRUCTIONS MA-1540
GLASS INSTRUCTIONS
GLASS DIAGRAM
STEP 1 STEP 2 STEP 3
STEP 1
REMOVE GLASS HOLDER BY REMOVING THE 2 SCREWS TOP
AND BOTTOM INSIDE FIXTURE. SLIDE PANES OF GLASS INTO
THE SIDES OF THE FIXTURE AND SECURE BY RE-ATTACHING
GLASS HOLDER.
STEP 2
CAREFULLY INSERT DOOR GLASS INTO DOOR THROUGH TOP
OPENING. COVER THE TOP CORNERS OF THE DOOR WITH A
SOFT CLOTH AND PINCH WITH A PAIR OF PLIERS TO SECURE
THE GLASS IN PLACE.