urmet domus IPercom elekta steel 1060/18 User manual

DS 1060-119A LBT 20376
Mod.
1060
MODULO DI CHIAMATA ELEKTA STEEL
ELEKTA STEEL CALL MODULE
MODULE D’APPEL ELEKTA STEEL
MÓDULO DE LLAMADA ELEKTA STEEL
RUFMODUL ELEKTA STEEL
Sch./Ref. 1060/18

6DS1060-119A
ENGLISH
1 DESCRIPTION
The device Ref. 1060/18 is an Elekta Steel vandal-proof call module for Ipercom serverless system.
The main features are:
Signal management using 3.5” graphic colour display and evolved graphic user interface (GUI).
Simultaneous lock with pulse capacitance discharge (SE+; SE-) and no-voltage contact relay (C-NC-
NO) operation.
Garage gate lock low current operation (SE2).
Hall button input.
Door sensor input.
Audio repeat device control for use with hearing aid.
LAN connection with RJ45 connector and Power Over Ethernet (POE).
Set-up by means of 2 terminals for local power supply.
125 kHz integrated transponder key reader (Ref. 1125/50).
Infrared proximity sensor for user detection.
CCD colour camera with wide-angle lens.
Alphanumeric keypad with 18 buttons, three of which multifunctional.
2 INSTALLATION
Arrange the duct so that it ends in correspondence with the lower hole of the flush-mounting box.
Remove the lower cap from the wire hole (1).
Apply adhesive labels on the holes for the screws of the frame (2).
Install flush-mounting box at indicated height (3).
Fix the magnet (tamper) at the indicated height with the two-sided adhesive tape included (4).
Fix the frame to the flush-mounting body (5).
Make the electric connections.
Fix the calling module to the frame (5).
ALTO
TOP
HAUT
A
ALTO
TOP
HAUT
B
ALTO
TOP
HAUT
118 mm
1,55 ÷ 1,60 m
298 mm
1 2 3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•

7
DS1060-119A
The highlighted part of the magnet must face the wall of the box (in contact with the two-sided
adhesive tape).
2.1 DESCRIPTION OF TERMINALS
C Common lock relay contact
}
Simultaneous activation
NC Normally closed lock relay contact
NO Normally open lock relay contact
SE-
}
Discharge lock terminals
SE+
V+
}
Auxiliary power terminals
V-
]
PA Hall button terminals for operating lock relay
]
SP Open door sensor terminals
]
SE2 Garage gate contact terminals (NO)
]
AD Auxiliary power terminals
LAN Ethernet connector for LAN RJ45
READER Connector for integrated transponder key device
ALTO
TOP
HAUT
Screw M4 x 20
Antitheft special screw
130 mm
TAMPER
4
5

8DS1060-119A
3 CONNECTION INSTRUCTIONS
Refer to the instructions contained in the system manual for wiring, maximum distances and configuration
operations.
3.1 CONNECTOR AND WIRING WITH CAT5 WIRE
Use Urmet RJ45 connector kit for connections (product on sale until stocks last).
Connect the CAT5 wire to one of the RJ45 connectors with Urmet logo:
Insert the wire in the guide respecting the colour coding shown (Standard T568B).
8
1
Wire
No. Wire colour
1 White-Orange
2 Orange
3 White-Green
4 Blue
Wire
No. Wire colour
5 White-Blue
6 Green
7 White-Brown
8 Brown
Cut the wires which protrude from the guide by approximately 5mm, insert the guide in the plug and
crimp the plug with a specific tool.
Plug
8
1
~ 5 mm
8
1
Make sure that the grey sheath remains inside the plug.
This type of connection DOES NOT ensure double insulation..
4 TECHNICAL SPECIFICATIONS
Power voltage and consumption on terminals V+ e V-
Power voltage:............................................................................................................................... 44 – 57 Vdc
Max. consumption (video call) @48 V: .................................................................................................200 mA
Max. consumption (stand-by) @48 V: ....................................................................................................80 mA
Working temperature range: .................................................................................................. -10 °C ÷ +50 °C
Relay contact range C, NC, NO:
Maximum switching voltage: .................................................................................................................... 30 V
Maximum switching current: ...................................................................................................................3,5 A
Maximum switching load: ............................................................................................................. 40 VA 25 W
Garage gate relay contact range (SE2):
Maximum switching voltage: .................................................................................................................... 30 V
Maximum switching current: ...............................................................................................................200 mA
Max. distance from hall button: .............................................25 m with cable cross-section area 0.5 mm2
Max. distance from open door sensor: .................................50 m with cable cross-section area 1.5 mm2
Max. distance from supplementary power supply: .............100 m with cable cross-section area 1.5 mm2
Max. distance from capacitance lock: ................................100 m with cable cross-section area 1.5 mm2
Clean regularly with products suitable for metallic surfaces to keep the push-button panel looking
good in time. Do not use aggressive chemical products (e.g. solvents, ammonia, soda, etc.).
•
•

9
DS1060-119A
5 WIRING DIAGRAM
For connecting the device ref. 1060/18, follow the instructions provided in the Ipercom system (system
installation paragraph).
6 SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, URMET S.p.A. declares that the radio equipment type:
ELEKTA STEEL CALL MODULE Ref. 1060/18
is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
www.urmet.com

DS 1060-119A LBT 20376
Area tecnica
servizio clienti +39 011.23.39.810
http://www.urmet.com
e-mail: [email protected]
MADE IN ITALY
URMET S.p.A.
10154 TORINO (ITALY)
VIA BOLOGNA 188/C
Telef. +39 011.24.00.000 (RIC. AUT.)
Fax [phone] - 323