urmet domus Sinthesi Steel 1060/74 User manual

DS 1060-112B LBT 20367
Mod.
1060
POSTO ESTERNO VIDEO IP CON 2 TASTI
EXTERNAL IP VIDEO STATION WITH 2 PUSH BUTTONS
POSTE EXTERNE VIDÉO IP AVEC 2 TOUCHES
MICROALTAVOZ VIDÉO SOBRE IP CON 2 TECLAS
IP-VIDEOAUSSENSTELLE MIT 2 TASTEN
Sch./Ref. 1060/74 (50 Hz)

6DS1060-112B
ENGLISH
PERFORMANCE
The features of the IP video door phone on are the following:
Designed on 2-module Sinthesi Steel style.
Management of pedestrian door electric lock with pulse capacitive discharge and with low holding
current (SE+; SE-).
Management of driveway electric lock with relay SE2 with clean contacts (C-NC-NO).
Hall button input.
Door sensor input.
Audio repeat device control for use with hearing aid.
LAN connection with RJ45 connector and POE power.
Power supply of 30 external name holder tags max. with POE.
Management of 32 calling buttons, of which two on-board and 30 external with the use of expansion
modules Ref. 1158/82 and 1158/84;
2 terminal pins for external power supply of name holder tags, if necessary.
CCD colour camera with wide-angle lens.
2 pre-cabled call buttons.
Input for external camera, alternative to the local one.
Management of audio repeater device for hard of hearing people and module with voice messages and
leds.
PANEL INSTALLATION
1. Install the module at the height shown.
2. Fit the module holder frame in the flush-mounting box.
3. Fit the modules in the frame.
4. Tip the frame and connect wires.
5. Close the frame.
6. Fit the name tags on the removable front.
7. Fit the panel on the frame.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1,55 ÷ 1,60 m
12
Ref.1145/52
Ref.1145/53
Ref.1145/54
Ref.1158/42
Ref.1158/43
Ref.1158/44

7
DS1060-112B
3 4
5
6
7
EXP
connector for
button modules
with expansion
Ref. 1158/82 - /84
LAN
I2C
DIGITAL CONNECTOR
Connector for module
with voice messages
and led Ref. 1158/47
Ref.1145/52
Ref.1145/53
Ref.1145/54
Ref.1158/42
Ref.1158/43
Ref.1158/44
Dummy
transparent
name holder.
Final engraved
name holder.

8DS1060-112B
DESCRIPTION OF TERMINALS
SE+
}
Terminal pins of discharge electric lock with holding current for relay, if present
SE-
C Common lock relay contact
} SE2
NC Normally closed lock relay contact
NO Normally open lock relay contact
V-
}
Auxiliary power terminals
V+
]
ILL Terminal pins for external lighting of name holder tags
]
PA Hall button terminals for operating lock relay
]
SP Door open sensor terminals
V5 Reference for external camera signal
V3 External camera signal
]
AD/ILA Ref. 1158/48 hearing aid audio device terminals
EXP Connector for button modules with expansion Ref. 1158/82 and Ref. 1158/84
LAN Ethernet connector for LAN RJ45
I2C DIGITAL Connector for module with voice messages and led Ref. 1158/47
CONNECTOR
For further details, see the manual provided with the module with voice messages and leds.
Refer to the instructions contained in the system manual for wiring, maximum distances and configuration
operations.
Use Urmet RJ45 connector kit for connections (product on sale until stocks last).
CONNECTION TO BUTTON MODULE WITH EXPANSION UNIT
Ref. 1158/82 and Ref. 1158/84
Use the following connections to connect the IP video door phone to button modules with expansion unit
Ref. 1158/82 and Ref.1158/84:
ILL
1158/84
1158/84
1158/84
1158/84
1158/82
1158/84
1158/84
1158/84
AA
B B B
B
B
C
A 55 cm-long cable provided with the button module with
expansion unit Ref. 1158/82 and /84
B 20 cm-long cable provided with the button module with
expansion unit Ref. 1158/82 and /84
C20 cm-long cable provided with the outdoor IP video
station

9
DS1060-112B
EXTERNAL CAMERA CONNECTION
Instead of the camera present in the module, an
external camera can be connected to terminal pins
V3, V5.
To enable the external camera, move the jumper as
shown below.
WIRING INSTRUCTIONS WITH CAT5 WIRE
Fit the CAT5 wire in a RJ45 plug with Urmet logo:
Insert the wire in the guide respecting the colour coding shown (Standard T568B).
8
1
Wire
No. Wire colour
1 White-Orange
2 Orange
3 White-Green
4 Blue
Wire
No. Wire colour
5 White-Blue
6 Green
7 White-Brown
8 Brown
Cut the wires which protrude from the guide by approximately 5 mm, insert the guide in the plug and
crimp the plug with a specific tool. Plug
8
1
~ 5 mm
8
1
Make sure that the grey sheath remains inside the plug.
This type of connection DOES NOT ensure double insulation.
TECHNICAL SPECIFICATIONS
POWER VOLTAGE AND CONSUMPTION ON TERMINALS V+ V-
Power voltage:...............................................................................................................................44 ÷ 57 Vdc
Current consumption during video call (*) @48 V:................................................................................200 mA
Current consumption in standby (*) @48 V:..........................................................................................140 mA
Working temperature range: .................................................................................................. -10 °C ÷ +50 °C
(*) Current consumption of 30 external name holder tags is included.
Relay contact range C, NC, NO:
Maximum switching voltage: ................................................................................................................ 30 V
Maximum switching current: ...............................................................................................................3,5 A
Maximum switching load: ......................................................................................................... 40 VA 25 W
Max. distance from hall button: .............................................25 m with cable cross-section area 0.5 mm2
Max. distance from open door sensor: .................................50 m with cable cross-section area 1.5 mm2
Max. distance from supplementary power supply: .............100 m with cable cross-section area 1.5 mm2
Max. distance from capacitance lock: ................................100 m with cable cross-section area 1.5 mm2
RESTORE DEFAULT SETTINGS
Close the hall button and at the same time press the second button on the IP video door unit (the bottom
most one) for 20 seconds. After 20 seconds, the device will beep before restarting, then release both
buttons: the previous configuration of the IP video door unit will be lost.
•
•
TLC-EXT

DS 1060-112B LBT 20367
Area tecnica
servizio clienti +39 011.23.39.810
http://www.urmet.com
e-mail: [email protected]
MADE IN ITALY
URMET S.p.A.
10154 TORINO (ITALY)
VIA BOLOGNA 188/C
Telef. +39 011.24.00.000 (RIC. AUT.)
Fax [phone] - 323