urmet domus iPercom VOG 5+ 1761 Installation and operation manual

DS1761-047 LBT21282
Mod.
1761
SSSSSSSSSSSS
IP 5” VIDEO DOOR PHONE US
MONITEUR IP 5” US
VIDEOINTERFONO IP 5” US
Sch./Ref. 1761/18
(white / blanc / blanco)
Sch./Ref. 1761/19
(black / noire / negro)
PARAMETER CONFIGURATION BOOKLET
NOTICE DE CONFIGURATION DES PARAMÈTRES
MANUAL DE CONFIGURACIÓN PARÁMETROS
Interactive Links

2DS1761-047
ENGLISH
INDEX
1. GENERAL DESCRIPTION......................................................................................................................... 3
2. CONFIGURATION MENU......................................................................................................................... 3
2.1 Audio ............................................................................................................................................... 3
2.2 Video ............................................................................................................................................... 5
2.3 Language selection ........................................................................................................................ 5
2.4 Date and time ................................................................................................................................. 6
2.5 Activating the call forwarding function (master only) ...................................................................... 6
2.6 Call diversion function (master only) ............................................................................................... 9
2.7 Call button assignment ................................................................................................................. 11
2.8 Activation button assignment ....................................................................................................... 12
2.9 Automatic door open (master video door phone only) ................................................................. 14
2.10 Mute function .............................................................................................................................. 16
2.11 Touchless commands .................................................................................................................. 18
2.12 Exporting video messages (master only)....................................................................................... 19
2.13 System information ...................................................................................................................... 21
2.14 Restore factory setting ................................................................................................................. 22
FRANÇAIS.............................................................................................................................................. 23
ESPAÑOL................................................................................................................................................ 44
The document contains INTERACTIVE LINKS for faster and more ecient consultation.
Interactive Links

3
DS1761-047
1. GENERAL DESCRIPTION
This booklet describes the conguration of parameters and functions in the conguration menu of the video
door phone.
2. CONFIGURATION MENU
The conguration menu allows conguring the video door phone’s parameters and functions. On the
homepage, select the following icon , then press the key to display the conguration menu.
The display shows the following screen:
To exit the conguration menu and go back to the Homepage, simply press the key. In any
case, the video door phone exits the menu after 60 seconds of inactivity.
The and keys allow selecting parameters or functions within the menu. After selecting the last
displayed item, pressing the key again allows you to switch to the next conguration screen. When
selection has been made press the key to carry out the conguration.
Press the key to return to the conguration menu after selecting a parameter or function.
The congurable parameters and functions within the menu are described below.
2.1 AUDIO
In the conguration menu, select the “Audio” item to adjust the audio volume of the video door phone and
select the ring tone according to the type of call.

4DS1761-047
Press the and keys to select the parameter to be adjusted. After selecting the last displayed
parameter, pressing the key again allows you to switch to the next screen.
After selecting the parameter, press the and keys to adjust the value of the selected parameter.
After conguration is complete, press the key to conrm settings and return to the conguration menu.
Press the key to cancel and go back to the conguration menu.

5
DS1761-047
2.2 VIDEO
In the conguration menu, select the “Video” item to adjust the display brightness.
Press the and keys to adjust the brightness value. After conguration is complete, press the key
to conrm settings and return to the conguration menu.
Press the key to cancel and go back to the conguration menu.
2.3 LANGUAGE SELECTION
In the conguration menu, select the “Language” item to change the language of the video door phone.
Press the key to open the drop-down menu with the selection of available languages.

6DS1761-047
Press the keys and to select the language you wish to set, then press the key to conrm
your selection.
Press the key to go back to the conguration menu.
The “System language” item allows the language to be congured automatically when
conguring the Ipercom system.
2.4 DATE AND TIME
In the conguration menu, select the “Date and Time” item to set/change the date and time visible on the
video door phone.
Press the keys and to select the parameter to be congured, then press the key to carry out
the conguration.
• Date: the box on the left allows changing the format of the displayed date: DD/MM/YYYY or MM/DD/
YYYY. The boxes on the right show the date detected by the Ipercom system.
• Time: The box on the left allows changing the format of the displayed time: 24H or 12H. The boxes on
the right allow the time detected by the Ipercom system to be displayed. If the time detected is before
noon, AM is displayed in the last box, whereas PM is displayed, if it is after noon.
After conguration is complete, press the key to return to the conguration menu.
2.5 ACTIVATING THE CALL FORWARDING FUNCTION (MASTER
ONLY)
ATTENTION! To enable the function, a router providing Internet access to the video door phone must be
present.
The “Call forwarding” function allows forwarding an audio/video or audio only call to a Smartphone with
Android or iOS operating system.
In order to receive the call, the Urmet CallMe App must be installed on the Smartphone, connected to the
Internet via its own data connection or WiFi.
Depending on the Ipercom system conguration (“CallMe Manager Support” parameter enabled or
disabled) it is necessary to follow the correct procedure for conguring and activating the call forwarding
function:
CallMe Manager support enabled on the Ipercom system
1. Download the Urmet CallMe App from the Apple Store (IOS) or the Play Store (Android)
2. Create an account on the Urmet Cloud through the CallMe App.
3. Enable the account using the PDF document sent by the administrator and the CallMe App.
For the procedure required to create an account through the CallMe App, refer to the
“Conguring the CallMe App” appendix in the Ipercom system technical manual available at
the website www.urmet.com

7
DS1761-047
4. In the conguration menu of the video door phone, select “Call forwarding” to congure the function.
The display shows the following screen:
5. Press key on the video door phone to verify and activate the call forwarding function
Press key to cancel the activation of the function and return to the conguration menu.
6. If successful, a screen page conrming the activation of the function will be displayed.
Press the key to close the screen and return to the function menu.
If the operation failed, a screen page indicating that the activation of the function was not successful
will be displayed.
In this case, perform the procedure again, making sure that you perform the described steps correctly.

8DS1761-047
CallMe Manager support disabled on the Ipercom system
1. Download the Urmet CallMe App from the Apple Store (IOS) or the Play Store (Android)
2. Create an account on the Urmet Cloud through the CallMe App
For the procedure required to create an account through the CallMe App, refer to the
“Conguring the CallMe App” appendix in the Ipercom system technical manual available at
the website www.urmet.com
3. In the conguration menu of the video door phone, select “Call forwarding” to congure the function.
The display shows the following screen:
4. Launch the application on the smartphone where the CallMe App is installed.
5. Press button: “Settings” → “Service Manager” → “My Devices” → “Add”.
6. The QR Code Reader application on your smartphone is launched. Scan the QR Code shown on the
video door phone display with your smartphone.
7. Press key on the video door phone to verify and activate the forwarding call function.
Press key to cancel the activation of the function and return to the conguration menu.
8. If successful, a screen page conrming the activation of the function will be displayed.
Press the key to close the screen and return to the function menu.
If the operation failed, a screen page indicating that the activation of the function was not successful
will be displayed.

9
DS1761-047
In this case, perform the procedure again, making sure that you perform the described steps correctly.
2.6 CALL DIVERSION FUNCTION (MASTER ONLY)
The call diversion function allows a call from a call station to be diverted to a contact in the address book.
In the conguration menu select “Call diversion” to activate the function.
Press the key to open a drop-down menu containing the contacts in the address book.
Press the keys and to select the contact, then press the key to conrm the contact to which
the call is diverted.

10 DS1761-047
After selecting the contact, the following parameters can be congured:
Press the keys , , and to select the parameter and value to be congured, then press the
key to conrm.
• Diversion delay (sec): this parameter allows setting the waiting time within which the call will be
diverted (from 0 to 40 seconds).
• Diversion on busy: if set to ON, this parameter allows diverting the call if the video door phones in
the apartment are busy with another call.
It is possible to change the contact associated with the function by repeating the procedure described
above.
The key allows exiting the page and returning to the conguration menu.
If you wish to disable the diversion function, simply press the key to select the following icon and
press the key .
The display shows the following screen:
Press the key to conrm disabling of the function.
Press the key to cancel and return to the contact selection screen.

11
DS1761-047
2.7 CALL BUTTON ASSIGNMENT
Select the “Call button assignment” item in the conguration menu to associate a contact in the phone
book with the , key, so that an intercom call can be made to the selected contact without having to
access the video door phone book.
Press the key to display the list of contacts in the video door phone book.
Press the and keys to select the contact you wish to associate with the . key. Then press the
key to conrm your selection.
The contact associated with the intercom key can be changed by repeating the procedure described
above.

12 DS1761-047
The key allows exiting the page and returning to the conguration menu.
If you wish to remove the contact associated with the key simply press the key to select the
following icon and press the key .
The display shows the following screen:
Press the key to conrm disabling of the function..
Press the key to cancel and return to the contact selection screen.
2.8 ACTIVATION BUTTON ASSIGNMENT
In the conguration menu, select the “Activation button assignment” item to associate a special function
to the , key. In this way it is possible to activate the selected function without having to access the
activation list on the homepage.
Press the key to display the list of activations present.

13
DS1761-047
Press the and keys to select the activation you wish to associate with the key. Then press
the key to conrm your selection.
You can change the activation associated with the special function key by repeating the procedure
described above.
The key allows exiting the page and returning to the conguration menu.
If you wish to remove the activation associated with the key , simply press the key to select the
following icon and press the key . The display shows the following screen:

14 DS1761-047
Press the key to conrm the removal of the activation.
Press the key to cancel and return to the activation selection screen.
• select the box of the Hearing impaired function on key 8.
2.9 AUTOMATIC DOOR OPEN (MASTER VIDEO DOOR
PHONE ONLY)
The following parameter allows the automatic door open function to be activated and programmed during
the various days of the week.
In the conguration menu select “Automatic door open” to congure the function.
Press the key to select the function mode.
• OFF: function disabled
• ON: function enabled
• TIMER: function enabled according to the programmed schedule
Press the and keys to select the day on which you wish to set the automatic door opener.
By pressing the key after selecting the last day on the screen, you can switch to the next screen where
the next days of the week are displayed.

15
DS1761-047
After selecting the day, press the key to set the function to ON.
The key allows you to scroll through and select the various parameters for enabling the function:
• Hour, minutes and denition of start time of the function (red box)
• Hour, minutes and denition of end time of the function (blue box)
The and keys allow you to congure the parameters listed above.

16 DS1761-047
The icon associated with the selected day allows the conguration to be copied and applied to the
following day, e.g. by pressing the icon on Wednesday, the conguration will also be copied on Thursday.
2.10 MUTE FUNCTION
The following parameter is used to activate and programme the MUTE function on the video door phone.
In the conguration menu select “Ringtone mute” to congure the function.
Press the key to select the function activation mode.

17
DS1761-047
• OFF: function disabled
• ON: function enabled
• 8h: function enabled for a maximum time of 8 hours
• TIMER: function enabled according to the programmed schedule
To programme the schedule press the key and select the days on which you want to enable the MUTE
function.
By pressing the key after selecting the last day on the screen, you can switch to the next screen where
the next days of the week are displayed.
After selecting the day, press the key to set the function to ON.
The key allows you to scroll through and select the various parameters for enabling the function:

18 DS1761-047
• Hour, minutes and denition of start time of the function (red box)
• Hour, minutes and denition of end time of the function (blue box)
The and keys allow you to congure the parameters listed above.
The icon associated with the selected day allows the conguration to be copied and applied to the
following day, e.g. by pressing the icon on Wednesday, the conguration will also be copied on Thursday.
2.11 TOUCHLESS COMMANDS
The following parameter allows enabling gesture commands on the video door phone.
In the conguration menu select “Touchless commands” to congure the function.

19
DS1761-047
Press the key to select the “Gesture” box, then press the key to enable the function.
For all information on the use of gesture commands click on the corresponding link and download the
Complete use booklet to gesture commands.
2.12 EXPORTING VIDEO MESSAGES (MASTER ONLY)
If a video message is particularly important, it can be exported from the video door phone using a microSD-
type memory card.
Insert the microSD card into the suitable slot.
In the conguration menu, select the “Video Messages Export” item; the display will show a screen with
all recorded video messages.
Press the and keys to select the video clip, and press the key to start viewing.
Each saved video clip shows the date and time it was taken. The red dot to the right indicates that the
video clip has not yet been viewed.
By pressing the key, the following icon can be selected to export the selected video clip.

20 DS1761-047
Press the key to conrm your selection; the following screen appears on the display:
If the export was successful, the following screen will appear after a few seconds:
Press the key to return to the video message export page.
By pressing the key twice, the following icon can be selected to export all present video clips.
Press the key to conrm your selection; the following screen appears on the display: