US Automatic PN-030215 B Technical specifications

Carrier frequency..............................433.92 MHz
Modulation........................................AM/ASK
N° channels ......................................1
E.r.p. .................................................300 uW
Battery type ......................................ER14505 Lithium
Operating voltage .............................3.6 Vdc
Current consumption ........................2 µA : stand-by
..........................................................60 mA : transmission
Battery life:........................................ ~2 years
Security protocol...............................xed code
Code combinations...........................3exp9
Typical range in open space.............~200m / ~656 feet
Operating temperature .....................-20°/+80°C
Enclosure IP grade ...........................IP55
Dimensions (mm) .............................105 x 70 x 23.5
Weight ( gr. / oz) .....................................100 / 3.53
The push-to-operate wireless button operates at 433.92 MHz in AM/ASK
modulation.
It’s mainly composed by a capacitive touch sensitive circuit and by a radio
trans-mitter. It can be used to operate gates, doors or garage doors or any
device with the corresponding compatible 433 MHz receiver.
The security protocol is fixed with 19683 code combinations .
A special sensor lights the led frame when the hand approaches the device
at about 10 cm and triggers the radio transmission when it touches the front
surface. The enclosure allows outdoor installations ( IP55).
Each product is already factory programmed with a different security code.
The transmitter is supplied with a ER14505 lithium battery for ~2 yearsof life.
PUSH TO OPERATE WIRELESS BUTTON
PN-030215 B (B for black housing)
PN-030215 W (W for White housing)
2Technical Specications
1 Introduction
Fig. 2
70mm
2.76 in
105mm
4.134 in
23.5mm
.93 in
3Mounting 4Battery replacement
+
_
ER14505
3.6 V
NOTE: Please dispose of the baeries correctly, they are
hazardous waste.
Replace the battery with ER14505 or equivalent
!respecting the polarity as shown above
Fig. 3
Fig. 4
Use and Installation manual
Dimensions (in) .............................4.134 x 2.76 x .935

USAutomatic, LLC warrants this product to be free of defects in materials and workmanship for 1YEAR. For a period of 1YEAR
following purchase USAutomatic, LLC. will repair or replace the product free of charge, including parts, shop labor and return to
customer shipping and handling. This 1YEAR warranty does not cover the plastic case from normal wear or damage due to
misuse of the Push To Operate module. To have the product sent for warranty consideration, contact the dealer or distributor the
product was purchased from to obtain the return authorization number. The return authorization number must be clearly marked on
the outside of the return package or it may not be accepted.
5Operate
7 Programming
6Battery Low
11 Warranty
BEEP
BLUE
GREEN
BEEP
BLUE
RED
Press the receiver P1 button and hold until green LD light comes ON. While LD light is ON place hand on the Push To Operate
when the buzzer sounds programming is complete. The receiver LD light must be ON when placing hand on the Push to Operate.
Any changes or modications on equipment not expressly approved by the manufacturer could void the user’s authority to operate
with the equipment.
USAutomatic,LLC
1-888-204-0174
www.usautomatic.com
10 Notice
IS-TTHUAEN rev.0 on 16/2/2018
This device complies with Part 15 of the FCC Rules provided it is assembled in exact accordance with the instructions provided with
this kit. Operation is subject to the following conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received including interference that may cause undesired operation.
FCC ID = PWJTTH
9FCC
8Battery replacement
This device uses a lithium battery type ER14505. Insert the new battery in the battery location, respecting the right polarity. The
removal and the disposal of the battery must have effected before the elimination of the appliance and according to the current
Regulations.
ATTENTION: - Danger of explosion if the battery is not replaced in the correct way! Replace only with an equal or equivalent type.
The light of the touch transmitter becomes BLUE when the
hand approaches at about 10 cm / 3.9 inches and becomes
GREEN when the hand touches the surface. The RF
transmission starts at the “Beep” of the buzzer.
If battery is low the GREEN color becomes RED.
The Button operates when you skim over the external surface with
the hand. The sensitivity of the detector can change according to
the mounting surface type: metallic surfaces increase the
sensitivity but can reduce the range of the radio transmission.
Approach the cover or touch it until the buzzer sounds. The
RF transmission lasts while the buzzer sounds. Normally it’s
necessary to skim over the cover with the hand and not with a
single finger.