US Automatic PATRIOT RSL User manual

DL12 Limit Assembly Gear Spacing
Problem description: If the open and close position are changing randomly when the gate is operated
the possible cause can be limit assembly gear spacing. To inspect and adjust this follow the steps below.
1. Disconnect the actuator cable from the control board.
2. Remove the 5 bolts holding the rear cover on the actuator. 5/16 head size.
3. Inspect the spacing between the blue and white gear.
4. Loosen the 4 screws to allow the limit assembly to slide over against the blue gear.
5. Once limit assembly white gear spacing is adjusted tighten the 4 screws.
NOTE: Do not apply pressure to the limit assembly just slide over until space is reduced and
tighten screw.
Loosen 4 screws
Five bolts holding rear cover 5/16
1 not shown
The gap between the blue and white
gear

TheillustrationbelowshowshowtowiretheLCRreceiverP2channelsothattheremotecontrolcan
turnONorOFFtheaccessory.ThisallowscustomertoswitchONorOFFanaccessorysuchasawired
keypad,exitsensoretc...ThereceiverP2shouldbeprogrammedtolatchmode.
OnceremotebuttonisprogrammedtoP2andP2isinthelatchingmodetheremotecanthenenableor
disabletheaccessoryfunction.


LCRReceiver
Part#030205
RedblackOrange
+ Ͳ N/O
Keypad/FreeExit/etc..
RelayCommon RelayN/O
PatriotControlboard

J2pin2or7 J2pin1  J2pin?
Ground 12vdcPowerRelayN/OfromAccessory
ProgrammingP2toLatchmode
1. PressP2andholddownuntilgreenlightcomesON.
2. VerifyiflightissolidorflashinggreenwhenitfirstcomesON.
3. IfsolidthenimmediatelyreleaseP2andpressP1once.
4. VerifymodewaschangedtolatchbypressingP2andholduntilgreenlightcomesON.
5. IfgreenlightisflashingwhenitfirstcomesONlatchmodeisset.

PatriotGateLeafDelay


Subject:PatriotSoftwareChange_2014
SoftwareRevision–5p10.hex
EffectivecontrolboardserialnumberͲTBD
Reason:Gateleafdelay(2seconds)foroverlappinggatesandelectricgatelockinstalledondualgates.
Changedescribedbelow:
Toactivatethegateleafdelayoption
Gate1andGate2EnableswitchesͲDS1dipswitch3and4mustbeON.
SolenoidLockEnableswitchͲDS2switch1mustbeON
Howitworks:
WhenthegatesareclosedonanopencommandGate2willdelaystartupfor2seconds.
WhenthegatesareopenonaclosecommandGate1willdelaystartupfor2seconds.
ThiswillallowGate2toclosebeforeGate1by2seconds.





HowtowireOpengatelightindicatortoPatriotcontrolboard
Onceconnectedturnonthedipswitchnumber3labeledsecurityshuntenableinthelowerrightcorner
ofthecontrolboard.Dipswitch(DS2)isthesmallredblockwith4whiteswitches.
12vdcLight
BatteryNegativepost
+12vdclightconnection
Jumperwire
Lowerrightcornerofcontrolboard
SecurityshuntterminalHas2screwsforthe
connectionof2wires
ConnectjumperwirefromJ2pin1tooneside
thenconnectthelight+12vdctotheotherside.
J2greenconnector
Connectjumperwiretopin1

J2greenconnector

White Plug connecting to Circuit Board (Rear View)
TOP
Black Wire to Red Wire to
Battery Battery
Green Wire No Wire Connected
Black Wire with Red Wire with
White Stripe White Stripe
Orange Wire White Wite
BOTTOM
Inside back of actuator
Red wire with white stripe is connected to the red lead going to the motor
Black wire with white stripeis connected to the yellow lead going to the motor.


PhotoEyePowerManagement(PEPM)
PurposeofPEPMistoallowtheinstallationofPhotoEyesonallPatriotorRanger
installationwithoutdrainingthebattery.Thisisaccomplishedbyonlyapplyingpowerto
thePhotoEyewhenthegateistravelinginthecloseddirection.
PatriotWiringisidenticaltowhatwehavedoneinthepastusingthesecurityshunt.
PEPMActivationrequiresthatdipswitch10locatedonDS1beturnedON.Thisswitchis
currentlymarkedas“NotUsed”.
RangerWiringisalittleeasier.Simplyconnectthe12vdcpowerwirefromthePhotoEye
toJ2connector(Green13pinconnector)pin5.
PEPMActivationrequiresthatdipswitch6locatedDS1beturnedON.Thisswitchis
labeledPhotoEyeEnable.
xPEPMallowsforanybrandofPhotoEyetobeused.Itmustbea12vdcdevice.



USAutomaticPhotoEye
Part#550010
Send&ReceiveͲ12/24ACorDC
