US Robotics USR805453A User manual

1R24.0658.00
rev 2.1 08/06
Professional Access Point
Quick Installation Guide

2

3
Contents
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Installing the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
What’s Next? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Interpreting the Access Point Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

4

1
Getting Started
Package Contents
• Access Point
• Installation CD-ROM
•QuickInstallationGuide
• Ethernet Cable
• Power Adapter
• Two 5 dBi antennas
• Mounting Hardware
• Rubber Feet
What You Need in Order To Begin
• An administrator computer. This is the computer that you will use to set up and test
your new wireless network before adding live wireless clients. On this computer,
you must have
■Administrator rights
■A CD-ROM drive
■An HTML 4.01-compliant Web Browser (such as Internet Explorer 5.5 or later or
Netscape 7.0 or later) with JavaScript enabled
■An Ethernet connection to your existing network
The instructions in this guide require that you use a DHCP server. If you do not
have a DHCP server and you want to assign a static IP address to the access
point, see “Setting Up and Launching Your Wireless Network” in the
Adminis-
trator Guide
on the Installation CD-ROM.
• Your Professional Access Point product number, serial number, and MAC addresses,
which are on the label on the bottom of the access point.
USRobotics periodically updates both firmware and documentation for the Professional Access
Point. For the latest updates, visit www.usr.com/support/.
Installing the Access Point
When you install the first Professional Access Point to create a wireless network, you must pro-
vide basic configuration information. Subsequently-added access points automatically use the
same configuration information as the first access point. This guide leads you through the
steps for installing the first access point, including basic configuration. For more information
about installing multiple access points, see the
Administrator Guide on the Installation CD-
ROM.
Product
Number Serial Number MAC Address
5453 LAN ____ : ____ : ____ : ____ : ____ : ____
WLAN ____ : ____ : ____ : ____ : ____ : ____

2
Step 1: Connect the Access Point to the Network and to Power.
The first USRobotics Professional Access Point in your network must be installed and config-
ured using an Ethernet cable. Make the following hardware connections:
1. Attach the antennas to the access point.
2. Connect one end of the supplied Ethernet cable to the LAN port on the access point,
and connect the other end to the same network that the administrator computer
uses.
3. Connect the supplied power adapter to the 5.0 VDC port on the access point, and
plug the power adapter into a standard power outlet.
Note to UK Users: Replace the plug on the power adapter with the UK standard
plug that is supplied in your USRobotics package. Apply enough pressure to cause a
click and firmly seat the new plug in the adapter.
Administrator
Computer
Professional Access Point
Router
Administrator
Computer
Professional Access Point
Router

3
Note: The access point may take up to one minute to boot. To ensure a smooth installation pro-
cess, USRobotics recommends that you wait one minute before proceeding with Step 2.
Step 2: Open the Access Point’s Web User Interface.
For Windows Operating Systems
1. Insert the USRobotics Installation CD-ROM into the CD-ROM drive on the adminis-
trator computer and select Setup from the menu.
The Professional Access Point Detection Utility starts automatically and displays its
Welcome screen:
If the CD-ROM does not start automatically, navigate to the CD-ROM drive and dou-
ble-click setup.exe.
Note: If you receive a Windows Security Alert from your Windows Firewall, click
Unblock to enable the java program to access your network. If network access
is blocked, the Detection Utility cannot find your access point.
2. Click Next and wait until the Detection Utility finds your access point.
If the Detection Utility does not find the access point, click Back and then click Next
to restart the scan. If the second scan does not find the access point, go to the
“Troubleshooting” section of this guide and follow the instructions under “The
Detection Utility does not find the access point.”

4
3. Click Next to display the page that will start the configuration process.
4. In the Detection Utility window, click Administration Console.
For Non-Windows Operating Systems
1. Using the configuration program for the networking device, such as a router, to
which the access point is connected, view the device’s client list.
2. Find the LAN MAC address of the access point in the client list.
3. Note the IP address that corresponds to the LAN MAC address of the access point.
4. Open a Web browser, enter the IP address in the address or navigation bar, and click
Enter.
Step 3: Configure Basic Settings.
Before giving you access to the Web User Interface, the system prompts you for a user name
and password:
Enter the password and click OK. The Basic Settings page appears.
The default value for both User Name
and Password is admin.

5
Review Description of this Access Point
Type a description of the access point’s location.
Provide Network Settings
■In Current Password, type admin.
■Type a New Password that is eight or fewer alphanumeric characters (0–9, a–z,
A–Z). Do not use special characters or spaces.
Note: The Password field is case sensitive, so be sure to remember exactly
how you enter it.
■Type the new password in Confirm New Password.
■Type a Network Name. This is the SSID of the network and must be 32 or fewer
alphanumeric characters.
Set Configuration Policy for New Access Points
Leave this value set to the factory default, are configured automatically.
Settings
Click Update to save your basic settings.
Step 4. Configure Security.
Your wireless network is now open to wireless devices within operating range. To prevent
access by unauthorized users, you must apply security to the access point as follows:
1
2
3
4

6
1. From the Advanced menu, select Security.
2. Select a Security Mode other than None, and mode-specific options appear on the
screen.
USRobotics recommends that you use one of the WPA/WPA2 options so that you
have the maximum level of security on your network. For more information about
the security modes available on the Professional Access point, see the
Administra-
tor Guide
on the Installation CD-ROM.
3. Enter the mode-specific security options, including a security key, and click Update.
Please register your Professional Access Point by going to www.usr.com/productreg/. For con-
figuration details, regulatory information, and warranty information, see the
Administrator
Guide
on the USRobotics Installation CD-ROM.
What’s Next?
Backing Up the Access Point Configuration
Now that you have configured your first access point, U.S. Robotics recommends that you back
up your configuration. If you ever need to reset your access point to its factory default settings,
having a configuration backup will quicken the process of restoring your network configura-
tion.
1. From the Advanced menu, select Backup/Restore.
2. Click download configuration.
3. When the File Download window appears, click Save.
4. Browse to the location where you want your configuration saved and click Save.
For information about restoring a saved configuration, see the
Administrator Guide on the
Installation CD-ROM.
Congratulations! The installation procedure is complete!

7
Adding a Wireless Client
You can now connect wireless devices to your new wireless network. To access the network,
the wireless adapter in each device must support the same mode as the access point—either
802.11b or 802.11g—and must be configured with the same security mode and security key as
the access point. For information about configuring the adapter in your wireless device, refer to
the adapter’s documentation.
Defining Virtual Networks
The Professional Access Point lets you use VLANs to establish both an internal network and a
guest network as well as two additional VLANs. The guest network is a way for you to allow
unsecured wireless access to the Internet or to public areas of your network. While the internal
network may use either dynamic or static IP addressing, the guest network must use dynamic
IP addressing through a DHCP server on the wired network.
For more information about the guest network, see “Setting Up Guest Access” in the
Profes-
sional Access Point Administrator Guide
.
For more information about VLANs, see “Configuring Virtual Wireless Networks” in the
Profes-
sional Access Point Administrator Guide
.
Adding Another Access Point
When you add a Professional Access Point to your new wireless network, it automatically clus-
ters with existing Professional Access Points that reside on the same wired network. The basic
configuration settings of the first access point are shared with the additional access points
automatically. Note, however, that guest network settings are not shared among access points
in a cluster: each access point needs its own guest settings.
Up to eight access points can belong to a single cluster. For more information about clusters,
see “Managing Access Points and Clusters” in the
Professional Access Point Administrator
Guide
.
Interpreting the Access Point Indicators
The front of the Professional Access Point has the following LED indicators:
Symbol Name State Condition
Power Off Not receiving power.
Solid Receiving power.
WLAN Off Radio is off.
Flashing Radio is on.
LAN
Off Not connected to LAN.
Solid Ethernet LAN link is achieved.
Flashing Sending or receiving Ethernet data.

8
Troubleshooting
The installation procedure does not begin when I insert the Installation
CD-ROM.
Possible Solution:
You may be running a program that interferes with the autolaunch feature of the CD-ROM. Nav-
igate to your CD-ROM drive and launch Startup.exe.
The Detection Utility does not find the access point.
Possible Solution 1:
1. Ensure that all cables are plugged in firmly, and verify that the access point’s power
indicator is lighted.
2. In the Detection Utility, click Back and then click Next to restart the discovery proc-
ess.
Possible Solution 2:
You can open the access point’s Web User Interface without using the Detection Utility by typ-
ing the IP address in your Web browser’s navigation or address bar. To find the IP address of
the access point,
1. Using the configuration program for the networking device, such as a router, to
which the access point is connected, view the device’s client list.
2. Find the LAN MAC address of the access point in the client list.
3. Note the IP address that corresponds to the LAN MAC address of the access point.
Possible Solution 3:
You can perform access point configuration by using a direct connection. For more information
about using this method, see “Setting Up and Launching Your Wireless Network” in the
Admin-
istrator Guide
on the Installation CD-ROM.
I cannot access the Web User Interface.
Possible Solution 1:
Verify that you are entering the correct IP address in your Web browser.
Possible Solution 2:
Reboot the access point by disconnecting and then reconnecting its power adapter.
Possible Solution 3:
Verify the connection setting of your Web browser, and verify that the HTTP Proxy feature of
your Web browser is disabled.
Internet Explorer users:
1. Click Tools, click Internet Options, and then click the Connections tab.
2. Select Never dial a connection, and then click the LAN Settings button.
3. Clear all the checkboxes and click OK.
4. Click OK again to apply the connection setting.
Mozilla-based browser users:
1. Click Edit, Preferences, and then double-click Advanced in the Category window.
2. Click Proxies, select Direct connection to the Internet, and then click OK.

9
My wireless device cannot find the wireless network.
Possible Solution 1:
Ensure that the access point is broadcasting its SSID:
1. Open the Web User Interface of the access point.
2. From the Advanced menu, select Security.
3. Verify that Broadcast SSID is set to Allow.
4. Click Update to save any change.
Possible Solution 2:
Reboot the access point by disconnecting and then reconnecting its power adapter.
My wireless device cannot connect to the wireless network.
Possible Solution 1:
Ensure that the wireless device is set to Infrastructure mode and has the following settings in
common with the access point:
• SSID, also called Network Name.
• Kind of security (for example, WPA/WPA2)
• Security key value
If you change the settings on the access point, remember to change the settings on your wire-
less devices also.
Possible Solution 2:
I am experiencing poor wireless link quality.
Possible Solution 1:
Reposition the access point or the wireless device so that environmental factors, such as lead-
based paint or concrete walls, do not interfere with your wireless signal.
Possible Solution 2:
Create a wireless connection on a different channel so that electronic devices, such as 2.4 GHz
phones, do not interfere with your wireless signal. For more information about changing chan-
nels, see “Channel Management” in the
Administrator Guide .
I need to configure the access point with an operating system other
than Windows.
Possible Solution:
You must configure the access point through its Web User Interface as follows:
1. Find the access point’s IP address:
■Using the configuration program for the networking device, such as a router, to
which the access point is connected, view the device’s client list.
■Find the LAN MAC address of the access point in the client list.
■Note the IP address that corresponds to the LAN MAC address of the access
point.
2. Launch a Web browser, type the IP address of the access point in the browser’s nav-
igation bar, and press Enter.
3. You can now log in and perform access point configuration as described in “Step 3:
Configure Basic Settings.”

10
Additional Information
For Regulatory and warranty information, see the Administrator Guide on the USRobotics
Installation CD-ROM.
For operation and configuration information, see the Administrator Guide on the USRobotics
Installation CD-ROM.
For troubleshooting and technical support, see:
1. The Administrator Guide on the USRobotics Installation CD-ROM.
2. The Support section of the USRobotics Web site at www.usr.com/support/.
Many of the most common difficulties that users experience have been addressed in the
FAQ and troubleshooting Web pages for your phone. The support Web pages also contain
current support contact information and documentation.
3. Contact the U.S. Robotics Technical Support Department. To receive assistance, you need
your serial number.
Model Number Serial Number
5453
Country Webmail Voice
U.S. www.usr.com/emailsupport [phone]
Canada www.usr.com/emailsupport [phone]
Austria www.usr.com/emailsupport/de 07110 900 116
Belgium (Flemish) www.usr.com/emailsupport/bn 070 23 35 45
Belgium (French) www.usr.com/emailsupport/be 070 23 35 46
Czech Republic www.usr.com/emailsupport/cz
Denmark www.usr.com/emailsupport/ea 38323011
Finland www.usr.com/emailsupport/ea 08 0091 3100
France www.usr.com/emailsupport/fr 0825 070 693
Germany www.usr.com/emailsupport/de 0180 567 1548
Greece www.usr.com/emailsupport/gr
Hungary www.usr.com/emailsupport/hu 0180 567 1548
Ireland www.usr.com/emailsupport/uk 1890 252 130
Italy www.usr.com/emailsupport/it 800 979 266
Luxembourg www.usr.com/emailsupport/be 342 080 8318
Middle East/Africa www.usr.com/emailsupport/me [phone]
Netherlands www.usr.com/emailsupport/bn 0900 202 5857
Norway www.usr.com/emailsupport/ea 23 16 22 37
Poland www.usr.com/emailsupport/pl
Portugal www.usr.com/emailsupport/pt 21 415 4034
Russia www.usr.com/emailsupport/ru 8 800 200 20 01
Spain www.usr.com/emailsupport/es 902 117964
Sweden www.usr.com/emailsupport/se 08 5016 3205
Switzerland www.usr.com/emailsupport/de 0848 840 200
Turkey www.usr.com/emailsupport/tk 0212 444 4 877
UAE www.usr.com/emailsupport/me 0800 877 63
UK www.usr.com/emailsupport/uk 0870 844 4546
U.S. www.usr.com/emailsupport [phone]
Canada www.usr.com/emailsupport [phone]
Austria www.usr.com/emailsupport/de 07110 900 116
Belgium (Flemish) www.usr.com/emailsupport/bn 070 23 35 45

11
Belgium (French) www.usr.com/emailsupport/be 070 23 35 46
Czech Republic www.usr.com/emailsupport/cz
Denmark www.usr.com/emailsupport/ea 38323011
Finland www.usr.com/emailsupport/ea 08 0091 3100
France www.usr.com/emailsupport/fr 0825 070 693
Germany www.usr.com/emailsupport/de 0180 567 1548
Country Webmail Voice

12

13

14
Printed in Xxxx