V-tech VM344-2 User manual

Go to www.vtechphones.com
to register your product for
enhanced warranty support and
latest VTech product news.
VM344-2
Quick start guide
VM344-2 baby monitor system
Baby’s room Living room
Dim mode
With dim mode preset to on, your parent unit display will dim after 10 minutes of inactivity to conserve energy.
10 min inactivity
Press any buttons
Install the battery
THIS SIDE UP
Connect and power on - Baby unit
> 1m (3ft)
>1m (3ft)
CAUTION
The default volume of your parent unit
is level 4. If you experience high-pitched
screeching noise from your baby monitor
while positioning:
Make sure your baby units and parent unit
are more than 1 meter (3 feet) apart, OR
Turn down the volume of your parent unit.
•
-
-
Connect and power on - Parent unit
6U]KXOTMUT
6U]KXOTMUT 6U]KXOTMUT
2s
< 1m (3ft)
63ē
> 1m (3ft)
63ē
>1m (3ft)
<1m (3ft)
Once you power on your baby monitor, your parent unit displays image from baby unit , and the LI NK LED
light turns on.
The ON/OFF LED light of baby unit turns on. As baby unit is not being viewed, its ON/OFF LED light flashes.
Status check
63ē
63ē
63ē
Press VIEW to switch between the image of baby units and .
Press VIEW
Change different views - View Change different views - Patrol
Press PATROL to alternately view the image from baby units and every 10 seconds.
10s
Change different views - Split
Press SPLIT to view the images from all baby units at once.
What’s in the box

Specifications are subject to change without notice.
© 2016 VTech Communications, Inc. All rights reserved.
05/16. VM344-2_QSG_V6.Document order number : 96-011018-040-100
Overview - Parent unit
VIEW / LCD ON/OFF
PATROL
SPLIT
Antenna
Speaker
Stand
At least 1 meter
(3 feet)
Zoom
TALK
+ / VOL / -
On/off
MENU/SELECT
Arrow keys
Light indicators
Microphone
Overview - Baby unit
Microphone
Camera
Light sensor
Infrared LEDs
Temperature
sensor
Antenna
+ / VOL / -
Speaker
ON/OFF switch
ON/OFF light
Basic operation - Parent unit
Pan, tilt, zoom
Press and hold , , or to move the camera.
Press to zoom in or out.
Adjust speaker volume
Press + / VOL / -to adjust your parent unit speaker
volume. It determines the volume of sound
transmitted from your baby units.
63ē
63ē
63ē
63ē
63ē
63ē
Talk to your baby unit
Press and hold TALK and speak to your parent unit.
Your voice is transmitted to the baby unit.
63ē
63ē
63ē
Long press
63ē
63℉
More than
1 meter (3 feet)
63℉
Turn off the screen
Press and hold LCD ON/OFF to turn off the screen.
You can still hear sound from the selected baby unit.
LCD is turning off...
2s
Use the menu
Press MENU/SELECT to enter the menu, choose
a menu item, or save a setting.
While in the menu:
Press or to scroll up or down.
Press to select an item.
Press BACK to return to the main menu or
idle screen.
•
•
•
Alert Tone
Low Battery Tone
No Link Alert
Sound alert in split-view
Alert Tone
Low Bettery Tone
No Link Alert
Sound alert in split-view
Turn off the parent unit
Press and hold to power off your parent unit.
6U]KXOTMULL
6U]KXOTMULL
6U]KXOTMUT
2s
Basic operation - Baby unit
Adjust speaker volume
Press + / VOL / -to adjust your baby unit speaker
volume. It determines the talkback volume
transmitted from your parent unit.
Turn off the baby unit
Slide the ON/OFF switch to the right to power
off your baby unit.
Sound-activated Screen
On
O
Sound activation
Automatically turns on the parent unit screen when the baby
unit being viewed detects a sound after the screen is turned
off. When no sound is detected within 50 seconds, the
screen is automatically turned off to save power.
Insert the screws into the
holes and tighten the screws
until only 1/4 inch of the
screws are exposed.
If you drill the holes into a stud,
go to step 3.
-OR-
If you drill the holes into an object
other than a stud, insert the wall
anchors into the holes. Tap gently
on the ends with a hammer until
the wall anchors are flush with
the wall.
Mount the baby monitor (optional)
OR
Place the wall mount bracket on a
wall and then use a pencil to mark
the top and the bottom holes as
shown. Remove the wall mount
bracket and drill two holes in the
wall (7/32 inch drill bit).
NOTES
Check for reception strength and
camera angle before drilling the holes.
•
Align the wall mount bracket and
screws with the holes in the wall
as shown. Tighten the screw in the
middle hole first, so that the wall
mount bracket position is fixed.You
can tighten the other screw in the
top hole.
Place the baby unit on the wall
mount bracket.Tighten the screw
into the threaded socket at the
bottom to secure the baby unit.
The default angle of the wall mount bracket is 90 degrees. You
can maximize your baby unit’s viewing angles by tilting the wall
mount bracket.
Hold the baby unit, and then rotate the knob in anticlockwise
direction. This will loosen the joint of the wall mount bracket.
Tilt your baby unit up or down to adjust to your preferred angle.
Then, rotate the knob in clockwise direction to tighten the joint
and secure the angle.
Place the baby unit on the wall mount
bracket.Tighten the screw into the threaded
socket at the bottom to secure the baby
unit. Align the holes on the wall mount
bracket with the screws on the wall, and
slide the wall mount bracket down until it
locks into place.
Night vision
The baby unit has infrared LEDs that allow you to
see your baby at night or in a dark room. When the
baby unit detects low light levels, the infrared LEDs
turn on automatically. The images from this baby
unit is in black and white, and appears on screen.
NOTES
It is normal if you see a shor t white glare on your paren t
unit screen as the baby un it is adapti ng to the dark
environment.
When the i nfrared LEDs are on, t he image i s in black
and whit e. This is no rmal due to extern al light s ources .
TIP
Depending on the surroundings and other interfering
factors, like lightings, objects, colors and backgrounds,
the display resolution may vary. Adjust the baby unit’s
angle, or place the baby unit at a higher level to prevent
glare and blurry display.
•
•
•