V-tech Go Go Smart Wheels Car User manual

© 2015 VTech
Printed in China
91-003063-009
User’s Manual
RC SmartPoint®Racer

2
LIGHT-UP
DRIVER BUTTON
FORWARD/BACKWARD
BUTTONS
POWER
INDICATOR LIGHT
INTRODUCTION
Thank you for purchasing the VTech®Go! Go! Smart Wheels®RC
SmartPoint®Racer.
Grab the steering wheel-shaped remote control and race to victory with
the Go! Go! Smart Wheels®RC SmartPoint®Racer! Reid and his
race car will entertain your little one with playful music, fun sounds and
phrases. Use the remote control to drive the racer over SmartPoint®
locations to hear fun phrases, sounds, short tunes and sing-along songs.
INTRODUCTION

3
INCLUDED IN THIS PACKAGE
• OneRC SmartPoint®Racer
• Oneremotecontrol
• Oneuser’smanual
WARNING:
All packing materials, such as tape, plastic sheets, packaging locks
and tags are not part of this toy, and should be discarded for your
child’ssafety.
ATTENTION:
Pour la sécurité de votre enfant, débarrassez-vous de tous les produits
d’emballagetelsquerubansadhésifs,feuillesdeplastique,attaches
etétiquettes.Ilsnefontpaspartiedujouet.
NOTE:
Pleasekeepthisuser’smanualasitcontainsimportantinformation.
INCLUDED IN THIS PACKAGE
Unlock the packaging locks:
Turn the packaging lock counter-clockwise
several times.
Pull out and discard the packaging lock.

4
GETTING STARTED / BATTERY INSTALLATION
GETTING STARTED
BATTERY INSTALLATION – VEHICLE
1. Make sure the unit is turned OFF.
2. Locate the battery cover on
the back of the race car. Use a
screwdriver to loosen the screw.
3. Install 3 new “AAA” (AM-4/LR03)
batteries following the diagram
inside the battery box. (The
use of new alkaline batteries
is recommended for maximum
performance.)
4. Replace the battery cover and tighten the screw to secure.
BATTERY INSTALLATION - REMOTE CONTROL
1. Locate the battery cover on the back of
the remote control. Use a screwdriver to
loosen the screw.
2. Install 2 new “AAA” (AM-4/LR03)
batteries following the diagram inside
the battery box. (The use of new alkaline
batteries is recommended for maximum
performance.)
3. Replace the battery cover and tighten
the screw to secure.

5
BATTERY NOTICE
• Usenewalkalinebatteriesformaximumperformance.
• Useonlybatteriesofthesameorequivalenttypeasrecommended.
• Donotmixdifferenttypesofbatteries:alkaline,standard(carbon-
zinc) or rechargeable (Ni-Cd, Ni-MH), or new and used batteries.
• Donotusedamagedbatteries.
• Insertbatterieswiththecorrectpolarity.
• Donotshort-circuitthebatteryterminals.
• Removeexhaustedbatteriesfromthetoy.
• Removebatteriesduringlongperiodsofnon-use.
• Donotdisposeofbatteriesinfire.
• Donotchargenon-rechargeablebatteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.
PRODUCT FEATURES
1. OFF/MODE SELECTOR SWITCH – VEHICLE
To turn the unit ON, slide the OFF/
MODE SELECTOR SWITCH to the
REMOTE CONTROL MODE ( )
or STANDARD MODE ( ) position.
To turn the unit OFF, slide the OFF/
MODE SELECTOR SWITCH to the
OFF ( ) position.
BATTERY NOTICE / PRODUCT FEATURES

6
PRODUCT FEATURES
2. CHANNEL SELECTOR SWITCH
To allow the RC SmartPoint®Racer and remote control to function
together, slide the CHANNEL SELECTOR SWITCH ( ) to
the same location on the RC SmartPoint®Racer and remote control.
Note: If two or three RC SmartPoint®Racers are operating in the
same vicinity, place each unit on a different channel ( ).
(A maximum of three RC SmartPoint®Racers can operate in
one location.)
3. FORWARD/BACKWARD BUTTONS
In REMOTE CONTROL MODE, press the FORWARD
BUTTON or BACKWARD BUTTON on the remote to make
the race car go forward or backward. (The effective distance
for the race car to recognize the remote control is 9 ft. to 18 ft.
The distance will be shorter when the batteries are low.)
For your child’s safety, only use the motorized car on Go! Go!
Smart Wheels®playsets. Do not roll the car on your clothing,
body or hair while the motorized car is turned on. If something
gets caught in the car’s wheels while the motor is on, lift
the car up so it is no longer touching your child or slide the
mode selector switch to the off position to turn off the motor.

7
4. AUTOMATIC SHUT-OFF
To preserve battery life, the VTech®Go! Go! Smart Wheels®
RC SmartPoint®Racer will automatically power down after
approximately 60 seconds without input in STANDARD MODE and
120 seconds in REMOTE CONTROL MODE.In STANDARD MODE,
the unit can be turned on again by pressing the LIGHT-UP DRIVER
BUTTON or pushing the vehicle. In REMOTE CONTROL MODE,
press the LIGHT-UP DRIVER BUTTON or turn the unit off and on to
turn the unit on. (The remote control cannot wake up the race car.)
Note: The RC SmartPoint®Racer is in try-me mode in the packaging.
After opening the package, turn the vehicle off and on again to
proceed with normal play.
ACTIVITIES
1. Slide the race car’s OFF/MODE
SELECTOR SWITCH to either
REMOTE CONTROL MODE or
STANDARD MODE to turn the race
car ON.You will hear a song, a phrase
and sounds.The LIGHT-UP DRIVER
BUTTON will flash with the sounds.
2. Press the LIGHT-UP DRIVER
BUTTON to hear race car sounds,
songs and phrases. The LIGHT-UP
DRIVER BUTTON will flash with the
sounds.
ACTIVITIES

8
3. When the race car is in STANDARD
MODE, push the race car to hear
fun sounds and melodies. While a
melody is playing, push the vehicle
again to add in fun sounds on top of
the melody.The LIGHT-UP DRIVER
BUTTON will flash with the sounds.
4. For remote control play, turn the
race car to REMOTE CONTROL
MODE ( ). To drive the race
car with the remote control, ensure
both the race car and remote control
are set to the same channel number
with the CHANNEL SELECTOR
SWITCHES. Once both items
are on the same channel, press the FORWARD BUTTON or
BACKWARD BUTTON on the remote for some racing fun!
NOTE: For optimal performance, only play with your RC
SmartPoint®Racer, in REMOTE CONTROL MODE, indoors and
out of direct sunlight.
NOTE: When the RC SmartPoint®Racer is in REMOTE
CONTROL MODE, do not push the vehicle forward or backward
on surfaces. The RC SmartPoint®Racer should only be pushed
manually, forward and backward, in STANDARD MODE.
5. Operate up to three vehicles at once by putting each RC
SmartPoint®Racer on a different channel number using the
CHANNEL SELECTOR SWITCHES! (Each RC SmartPoint®
Racer sold separately.)
ACTIVITIES

9
6. For added fun, the RC SmartPoint®Racer interacts with the Go!
Go! Smart Wheels®Ultimate RC Speedway™and other Go! Go!
Smart Wheels®and Go! Go! Smart Animals®playsets. Simply
rollornavigatetheracecaroveroneoftheplayset’sSmartPoint®
locations to see the light flash and to hear greetings, fun sounds,
short tunes and sing-along songs (each playset sold separately).
For optimal performance, use the RC SmartPoint®Racer on
the Go! Go! Smart Wheels®Ultimate RC Speedway™(sold
separately) when in REMOTE CONTROL MODE.
ACTIVITIES