V-tech Go! Go! Smart Wheels Race Car User manual

Go! Go! Smart Wheels™Race Car
User’s Manual
BATTERY INSTALLATION
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the bottom of the
unit. Use a coin or a screwdriver to loosen the
screw.
3. Install 2 new “AAA” (AM-4/LR03) batteries
following the diagram inside the battery
box. (The use of new alkaline batteries is
recommended for maximum performance.)
4. Replace the battery cover and tighten the
screw to secure.
WARNING: All packing materials, such as tape, plastic sheets,
packaging locks and tags are not part of this toy, and
should be discarded for your child’s safety.
Attention : Pour la sécurité de votre enfant, débarrassez-vous
de tous les produits d’emballage tels que rubans
adhésifs, feuilles de plastique, attaches et étiquettes.
Ils ne font pas partie du jouet.
NOTE: Please keep user’s manual as it contains important
information.
BATTERY NOTICE
• Use new alkaline batteries for maximum performance.
• Use only batteries of the same or equivalent type as recommended.
• Do not mix different types of batteries: alkaline, standard (carbon-zinc) or
rechargeable (Ni-Cd, Ni-MH), or new and used batteries.
• Do not use damaged batteries.
• Insert batteries with the correct polarity.
• Do not short-circuit the battery terminals.
• Remove exhausted batteries from the toy.
• Remove batteries during long periods of non-use.
• Do not dispose of batteries in fire.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the toy before charging (if removable).
• Rechargeable batteries are only to be charged under adult supervision.
PRODUCT FEATURES
1. ON/OFF SWITCH
To turn the unit ON, slide the ON/OFF
SWITCH to the ON ( ) position. To turn
the unit OFF, slide the ON/OFF SWITCH to
the OFF ( ) position.
2. AUTOMATIC SHUT-OFF
To preserve battery life, the VTech®Go! Go! Smart Wheels™Race Car
will automatically power-down after approximately 60 seconds without input.
The unit can only be turned on again by pressing the light-up driver button or
pushing the race car quickly.
ACTIVITIES
1. Slide the ON/OFF SWITCH to turn the unit
ON. You will hear race car sounds, a song
and a phrase. The light will flash with the
sounds.
2. Press the LIGHT-UP DRIVER BUTTON to
hear race car sounds, songs and phrases.
The light will flash with the sounds.
3. Push the race car to hear fun sounds and
melodies. While the melody is playing, push
the race car again to add in fun sounds on
top of the melody. The light will flash with the
sounds.
4. For added fun, the race car interacts with
other VTech®Go! Go! Smart Wheels™
playsets. Simply roll the race car over one of
the playset’s SmartPoints™ to see the race
car’s light flash and to hear greetings, fun
sounds, short tunes and sing-along songs
(each playset sold separately).
12

CARE & MAINTENANCE
1. Keep the unit clean by wiping it with a slightly damp cloth.
2. Keep the unit out of direct sunlight and away from any direct heat source.
3. Remove the batteries when the unit is not in use for an extended period of time.
4. Do not drop the unit on hard surfaces and do not expose the unit to moisture
or water.
TROUBLESHOOTING
If for some reason the program/activity stops working or malfunctions, please
follow these steps:
1. Please turn the unit OFF.
2. Interrupt the power supply by removing the batteries.
3. Let the unit stand for a few minutes, then replace the batteries.
4. Turn the unit ON. The unit should now be ready to play again.
5. If the product still does not work, replace with a new set of batteries.
If the problem persists, please call our Consumer Services Department at 1-800-
521-2010 in the U.S. or 1-877-352-8697 in Canada, and a service representative
will be happy to help you.
For information on this product’s warranty, please call VTech® 1-800-521-2010 in
the U.S. or 1-877-352-8697 in Canada.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
34
91-002822-000
cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION
IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE
MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME À LA NORME
NMB-003 DU CANADA.
Caution: changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE:
Creating and developing Infant Learning products is accompanied by a
responsibility that we at VTech®take very seriously. We make every effort to
ensure the accuracy of the information, which forms the value of our products.
However, errors sometimes can occur. It is important for you to know that we
stand behind our products and encourage you to call our Consumer Services
Department at 1-800-521-2010 in the U.S. or 1-877-352-8697 in Canada, with
any problems and/or suggestions that you might have.A service representative
will be happy to help you.